Timer Operation; Using The On/Off Timer - Sanyo DC D30 Instruction Manual

RECORDING FROM THE TUNER, PHONO OR VIDEO INPUT
1. Tune in the radio station to be recorded, or play a record, video
4. Press the REC/PAUSE switch to temporarily stop recording. Press the
cassette or video disc.
switch again to continue.
2. Press the REC/PAUSE switch (" 11 " appears for 1 second). The REC/
5. Press the STOP switch to stop recording.
PAUSE indicator lights and the b or Q PLAY indicator blinks.
When using the remote control, press the /II switch.
When beat interference is heard
3, Press the REC/PAUSE switch again or press the b or < PLAY
A high-pitched noise called "beat" is sometimes heard during the record-
switch whose indicator is blinking. (" " appears for 1 second).
ing of radio broadcasts.
The recording starts. The b or Q PLAY indicator remains lit.
In cases Iikethis, set the BEAT CANCEL switch at the rear of the unit to the
- To record in the opposite direction to that indicated by the blinking
position (1 or 2) which will reduce the level of the beat noise.
indicator, press once the switch whose indicator is not blinking,
check that the other indicator is now blinking, and press the same
switch again.
TIMER OPERATION
ON/OFF timer:
This enables radio programmed to be recorded unattended. CD play
or tape playback can be started and stopped at the selected times.
WAKE UP timer:
This wakes you up to the sound of a CD, tape or radio.
SLEEP timer:
This allows you to fall asleep to the sound of a CD, tape or radio.
' Note:
Make absolutely sure that the clock shows the correct time before setting
the timer.
The TIMER, WAKE UP and SLEEP switches do not function while the
clock display is blinking.
USING THE ON/OFF TIMER
Set the ON and OFF times, then select the source to be used (for tuner,
select the band and a preset station). Operation will start with the selected
source at the ON time and the power will be switched off at the OFF time.
The timer settings are stored in the memory and retained even when the
timer operation has been completed.
Each time the ON/OFF timer is to be used, set the unit to the timer
operation standby mode.
1.
-2.
3.
4.
Press the TIMER switch.
~
The previous timer ON time setting appears.
Press the MEMORY switch within 5 seconds.
~
Set the timer ON time by pressing the V or A TUNING switch,
then press the MEMORY switch (as described under "ADJUSTING
THE CLOCK') .
I
1
0:2{!.
I
TM'.
The previous timer OFF time setting appears.
Set the timer OFF time as described in step 3.
~
o
1
5. Select the source bv pressing the V or
A
TUNING switch.
For radio reception (or for unattended recording)
The station used during timer operation must be preset.
a. Perform step 5 above until "TU" blinks. (Select "TU REC" for
unattended recording.)
I (
L
b. Press the MEMORY switch.
~
The band, preset number and frequency of the previous timer
operation are displayed.
c. Select the band using the BAND switch, then indicate the desired
preset number using the V or
A
TUNING switch.
6. Press the MEMORY switch.
The original display returns, then the timer operation standby mode is
activated. "TIMER" (or "TIMER REC") remains lit.
7, Prepare the sources to be used.
Note:
- For tape playback: Select P or Q If tapes have been loaded
into both decks, select deck A or deck B.
- Recording will start only from the forward side.
8. Press the POWER switch to switch off the power.
If the power is not switched off, the timer will not be activated at the set
time and the timer mode will be released.
To switch off the power during a timer controlled operation, press the
POWER switch. The ON/OFF timer will then be released.
To check the timer settings
Press the TIMER switch repeatedly. The timer settings are displayed in the
following order:
- ON time
- OFF time
- Source (If the tuner is being used as the source, the band, preset
number and frequency are displayed.)
- Original display returns.
To change the settings, press the TIMER switch to select the setting to be
changed, then press the MEMORY switch so that the display blinks.
Change the setting as explained above.
The previous source setting blinks.
-14-