Download Print this page

Tape Dubbing; Sleep Timer Operation - Sanyo DC-D27 Instruction Manual

Hide thumbs

Advertisement

RECORDING
FROM THE TUNER OR VIDEO INPUT
1.
Tune in the radio station to be recorded, or play a video cassette or
video disc.
2.
Load a blank cassette into deck B.
3.
Press the REC PAUSE button. Deck B enters the record pause mode.
4.
Press the D button. Recording starts.
5.
Press the REC PAUSE button to temporarily stop recording. Press the
D button again to continue.
6.
Press the
button to stop recording.
When beat interference
ia heard
A high-pitched
noise called "beat" is sometimes
heard during the record-
Load the cassette to be played back into deck A and a blank cassette into
deck B.
High-speed
dubbing
For simple, automatic dubbing in one-half the time, compared to normal-
speed dubbing.
1.
2.
3.
4.
ing of radio broadcasts.
If this occurs,
1.
Select "TUNER".
2.
Press the MEMORY button.
3.
While "PROG." is blinking, press the
>/
M SKI PK3EARCH button
to select "be-l" or %c-2". Select the setting that gives the best results.
TAPE DUBBING
(Deck A to Deck B)
Use the same length cassettes
in both decks for the high-speed
dubbing operation.
Press the DUBBING HIGH button. "TAPE
is selected automatically
and "dub appears on the display.
The system performs the steps below and automatically
starts deck
A playback and deck B recording.
1)
Deck A: Tape rewinds.
2)
Deck B: Tape rewinds.
3)
Deck B: Erases the first few seconds of the tape.
The REC PAUSE, DECK B and DECK A indicators
light, "dub
and
" F" appear on the display as dubbing begins.
When side A of deck A has been dubbed, both decks stop automati-
cally.
Turn over both cassettes and reinseri them.
Press the DUBBING HIGH button to dub side B of deck A.
Press the
button to stop dubbing at any time.
Before pressing the DUBBING
HIGH button, check that both decks
are in the stop mode.
-
The tape will not stop during high-speed
dubbing if the REC PAUSE
button is pressed.
During high-speed dubbing, normal monitoring
is not possible.
A high-pitched
sound maybe recorded if high-speed dubbing is used
near a TV. If this happens, switch off the TV or place the system at a
distance from the TV.
High-speed dubbing must start from the beginning of the tape. To start
dubbing from a position in the middle of the tape, use manual dubbing.
Manual (normal-speed)
dubbing
For dubbing while listening to the playback from deck A.
1.
Select "TAPE".
2.
Deck B: Locate the tape position where recording will begin.
3.
Deck A: In the forward direction, locate the selection of the tape to be
dubbed.
4.
Press the REC PAUSE
button. The REC PAUSE
and DECK B
indicators light. " F"
blinks on the display.
5.
Press the D button. The DECK A indicator and "
" light. Manual
dubbing starts.
Deck A playback will start in the forward direction.
6.
Press the
button to stop dubbing.
Automatic stop during tape dubbing
If deck A or deck B stops automatically,
the other deck will also stop.
During tape dubbing,
the DOLBY NR button has no effect on the
copied tape. If the tape to be copied is encoded with Dolby NR, the
copy will be Dolby NR encoded automatically.
SLEEP TIMER OPERATION
This timer automatically
switches off the power after a preset time has
To check the remaining
sleep time
elapsed. The volume will gradually be reduced (fade-out) during the 1-
Press the SLEEP button. The remaining time is displayed. After several
minute period before the unit turns off. There are 12 time periods available:
seconds, the original display returns.
120, 110, 100, 90, 80, 70, 60, 50,40, 30, 20, and 10 minutes.
To release the sleep timer while in operation
Press the SLEEP button on the remote control to select the desired sleep
Press the SLEEP button repeatedly until "SLEEP
disappears.
The timer
time. "SLEEP
and the selected time blink on the display. After several
is also released if the power is switched off.
seconds, the original display returns. "SLEEP
remains lit.
-11-

Advertisement

loading

  Also See for Sanyo DC-D27

  Related Manuals for Sanyo DC-D27