Table of Contents
Advertisement
RECORDING
Recording
copyright
material
without
permission
of the copyright
owners is usually an infringement.
If you wish to re-record copyright
material, permission from the copyright owner is necessary. SANYO
does not approve of, and cannot be held responsible for, any unlawful
use of this machine.
Recording compact discs (Synchronous
recording)
1.
2.
3.
4.
5.
6.
Load a blank cassette.
Select "CD function.
Load the disc to be recorded.
For programmed
recording, programme the material in advance
(as described under "PROGRAMMED
PLAY").
Select the track number to be recorded if required.
For programmed
recording, this step is unnecessary.
Press the REC button, The PLAY button is engaged simultaneously
and CD recording starts.
Press the STOP/EJECT
button to stop recording. Also the CD player
stops automatically.
When the end of the tape is reached, the CD player and deck stop
automatically.
Recording from the tuner or other sources
1.
Load a blank cassette.
2.
Tune in the radio station to be recorded or play other source.
3.
Press the REC button to start recording.
4.
Press the STOP/EJECT
button to stop recording.
—-
--, ..... ——
When beat interference
is heard
A high-pitched noise called "beat" is sometimes heard during the recording
of radio broadcasts.
If this occurs,
1.
Press the MEMORY button.
2.
While "PROG." is blinking, press the + TUNING button to select "BC-
1" or "BC-2,
Select the setting that gives the best results.
Safeguards
against accidental
erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive
tape and the tape can be used for
recording again.
Side A
TIMER OPERATION
—
Using the timer
(Main unit only)
Set the on and off times, and function to be used, Operation will start with
the selected function at the on time, The sound will be gradually increased
from a no-sound level to the current volume setting (fade-in). The power
will be switched off at the off time.
The timer will function every day unless it is released,
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before setting
the timer.
Prepare the sources to be used.
If the function selected is tuner, tune into the desired band and
station.
-
Adjust the volume level as desired.
Operation
1.
Press the CLOCKTIMER
button for at least 2 seconds.
The previous timer on time setting appears.
2.
Press the MEMORY button within 10 seconds.
\l/
1:1hd
I.-f.:ll:
.1 /1111
l,f_
_l
e
3.
Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under "ADJUSTING
THE CLOCK).
The timer off time setting appears,
4.
Set the timer off time as described in step 3.
The previous function setting appears.
,. . . -..
,"
.
. .
.
.
5.
Press the FUNCTION button to select the function for timer operation.
6.
Press the MEMORY button.
The original display returns, then the timer operation standby mode is
activated. '@" remains lit.
7.
Press the LYON button to switch off the power,
-
To switch off the power during a timer controlled operation, press the
~/ON button, The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCWTIMER
button twice. '~
disappears.
To set the timer again with the same settings
1.
Press the CLOCIVTIMER
button repeatedly to display '$?)".
2.
Press the WON button to switch off the power,
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer
(Remote
control
only)
The sleep timer automatically
switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
l-minute
period before the unit turns off. There are 12 time periods
available:
120, 110, 100, 90, 60, 70, 60, 50, 40, 30, 20 and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time,
"SLEEP
blinks and the selected time appears on the display. After a few
seconds, the original display returns. "SLEEP
remains blinking.
To check the remaining
sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until "SLEEP
disappears. The timer
is also released if the power is switched off.
-t?.
Advertisement
Table of Contents
