Toro Mower Safety - Toro 74534TE GrandStand Operator's Manual

Safe Handling of Fuels
•
To avoid personal injury or property damage, use
extreme care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
•
Extinguish all cigarettes, cigars, pipes, and other sources
of ignition.
•
Use only an approved fuel container.
•
Do not remove the fuel cap or add fuel with the engine
running.
•
Allow the engine to cool before fueling.
•
Do not fuel the machine indoors.
•
Do not store the machine or fuel container where there
is an open flame, spark, or pilot light, such as on a water
heater or on other appliances.
•
Do not fill containers inside a vehicle, on a truck, or on a
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
•
Remove equipment from the truck or trailer and fuel it
on the ground. If this is not possible, then add fuel with
such equipment as a portable container rather than from
a fuel-dispenser nozzle.
•
Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
•
Do not use a nozzle lock-open device.
•
If you spill fuel on clothing, change your clothing
immediately.
•
Do not overfill the fuel tank. Replace the fuel cap and
tighten securely.
Maintenance and Storage
•
Disengage drives, set the parking brake, stop the engine,
and remove the key or disconnect spark-plug wire. Wait
for all movement to stop before adjusting, cleaning, or
repairing.
•
Park the machine on a level surface.
•
Clean grass and debris from the cutting unit, drives,
mufflers, and engine to help prevent fires.
•
Clean up oil or fuel spills.
•
Let the engine cool before storing the machine.
•
Do not store fuel near flames or drain fuel indoors.
•
Do not allow untrained personnel to service the machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery or remove the spark-plug wire
before making any repairs. Disconnect the negative
terminal first and the positive terminal last. Connect the
positive terminal first and negative last.
•
Use care when checking the blades. Wrap the blade(s)
or wear thickly padded gloves, and use caution when
servicing them. Only replace blades; do not straighten
or weld them.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
Hauling
•
Use care when loading or unloading the machine into a
trailer or a truck.
•
Use full-width ramps for loading machine into a trailer
or a truck.
•
Tie the machine down securely using straps, chains, cable,
or ropes. Both front and rear straps should be directed
down and outward from the machine.

Toro Mower Safety

The following list contains safety information specific to Toro
products and other safety information you must know.
This product is capable of amputating hands and feet, and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
This product is designed for cutting and recycling grass, or,
when equipped with a grass bagger, for catching cut grass.
Any use for purposes other than these could prove dangerous
to the user and bystanders.
General Operation
•
Be sure that the area is clear of bystanders before mowing.
Stop the machine if anyone enters the area.
•
Do not touch equipment or attachment parts which may
be hot from operation. Allow all of the parts to cool
before attempting to maintain, adjust, or service the
machine.
•
Use only Toro-approved attachments. Warranty may be
voided if used with any unapproved attachments.
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires, etc.) before operating under
any objects, and do not contact them.
•
Slow down before making turns and use extra caution.
•
Use caution when riding the platform over curbs, rocks,
roots, or other obstructions.
•
Look behind and down before backing up to ensure a
clear path. Use extra care when operating in reverse.
•
Do not jerk the controls; use a steady motion.
•
When loading or unloading the machine, use one
full-width ramp that is wide enough to extend beyond
the width of the machine.
•
Do not carry passengers.
•
Do not carry equipment on the machine.
5