Related Manuals for Horizon Hobby Manta Blade
Summary of Contents for Horizon Hobby Manta Blade
- Page 1 ® Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.
-
Page 3: Table Of Contents
® Table of Contents First Flight Preparation ..................4 Post-Flight Inspection and Maintenance .............9 Flying Checklist ....................4 Changing Video Transmitter Frequency .............10 Assembly ......................4 AS3X Troubleshooting Guide ................10 Transmitter Setup ....................7 Troubleshooting Guide ..................10 Flight Battery Installation and ESC Arming ............7 Parts List......................11 Transmitter and Receiver Binding ...............7 Optional Parts List ....................11... -
Page 4: First Flight Preparation
First Flight Preparation Flying Checklist ❏ Always turn the transmitter on fi rst • Remove and inspect contents ❏ Plug the fl ight battery into the lead from the ESC • Begin charging the fl ight battery ❏ Allow the ESC to initialize and arm properly •... - Page 5 Install the Wings 1. Apply glue to the mating surfaces of the wing panel and center section. DO NOT apply glue to the end of the elevon or to the center section where the elevon meets it. 2. Carefully slide the wing panel fully onto the main spar until the wing panel and center section line up.
- Page 6 Install the Video Antenna Support 1. Ensure the video transmitter antenna connection is tight. If the antenna has loosened during shipping, remove the video transmitter cover and tighten the antenna. 2. Carefully fl ex the antenna cable until it is upright, perpendicular to the upper surface of the wing.
-
Page 7: Transmitter Setup
Transmitter Setup DX6, DX7 (Gen 2), DX8 (Gen 2), DX9, DX18, DX20 Program Your Transmitter SETUP LIST FUNCTION LIST 1. Set the model type to “Airplane.” 2. Assign channel 5 (Gear) to a 3-position switch. In the table at left, Model Type Servo Setup switch B is used. -
Page 8: Control Surface Centering
Control Surface Centering NOTICE: Remove the propeller and propeller adapter from the motor shaft during control surface adjustments. Any movement of the throttle (even accidental) will cause the propeller to spin. With the receiver powered on, center the controls and trims. When the controls are neutral, the elevons should have a slight upward defl... -
Page 9: Install The Propeller
Install the Propeller If you are using a 4S battery, a 5.5’ x 4.5’ propeller is recommended. If you are using a 3S battery, a 6’ x 4’ propeller is recommended. Install the propeller adapter, propeller, washer and nut on the motor shaft as shown. -
Page 10: Flying The Manta
Flying the Manta Consult local laws and ordinances before choosing a fl ying location. Range Check your Radio System Landing Before you fl y, range check the radio system. Refer to your specifi c transmitter For your fi rst fl ights with the recommended battery pack, set your transmitter instruction manual for range test information. -
Page 11: Changing Video Transmitter Frequency
Changing Video Transmitter Frequency NOTICE: Do not remove the clear plastic shrink wrap from around the video transmitter. Removal may result in damage to the components attached to the board. The supplied video transmitter is capable of transmitting on various frequencies within the 5.8GHz band. -
Page 12: Optional Parts List
Problem Possible Cause Solution Move powered transmitter a few feet from aircraft, disconnect and reconnect fl ight Transmitter too near aircraft during binding process battery to aircraft Aircraft or transmitter is too close to large metal object, Move aircraft and transmitter to another location and attempt binding again Aircraft will not Bind wireless source or another transmitter to transmitter... -
Page 13: Limited Warranty
Product in, please use the Horizon Online Service Request submission of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized process found on our website or call Horizon to obtain a Return Merchandise service center, (v) Product not purchased from an authorized Horizon dealer, (vi) Authorization (RMA) number. -
Page 14: Fcc Information
Compliance Information for the European Union EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance A copy of the EU Declaration of Conformity is available online at: with the essential requirements and other relevant provisions of the http://www.horizonhobby.com/content/support-render-compliance. - Page 15 ©2016 Horizon Hobby, LLC. Blade, DSM, DSM2, DSMX, AS3X, ModelMatch, Bind-N-Fly, the BNF logo, Thrust, Focal and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. All other trademarks, service marks and logos are property of their respective owners.
Need help?
Do you have a question about the Manta Blade and is the answer not in the manual?
Questions and answers