Related Manuals for Horizon Hobby Blade 450 X
Summary of Contents for Horizon Hobby Blade 450 X
- Page 1 ® ® ® Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni...
- Page 2 This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.
-
Page 3: Table Of Contents
Blade Helicopter Belt Tension ................9 Charging Warnings....................4 Post-Flight Inspections and Maintenance ............. 9 Battery Charging ....................4 AR7200BX Default Blade 450 X Setup ..............10 Low Voltage Cutoff (LVC) ..................5 AR7200BX Parameter Menu Tips ............... 10 Installing the Transmitter Batteries ..............5 AR7200BX Fine-tuning and Adjustment .............. -
Page 4: First Flight Preparation
First Flight Preparation Flying Checklist ❏ Always turn the transmitter on fi rst • Remove and inspect contents ❏ Plug the fl ight battery into the lead from the ESC • Begin charging the fl ight battery ❏ Allow the ESC to initialize and arm properly •... -
Page 5: Low Voltage Cutoff (Lvc)
Low Voltage Cutoff (LVC) The ESC will continuously lower power to the motor until complete shutdown Repeatedly fl ying the helicopter until LVC activates will damage the helicopter when the battery reaches 9V under load. This helps prevent over-discharge of the battery. -
Page 6: Transmitter Setup
Mechanical Conversion Mechanical conversion is required to change between Modes 1 and 2. The the throttle gimbal. Tighten the opposite throttle strap to engage the desired mechanical conversion consists of the following steps: throttle ratchet. Removing the Rear Case: Adjusting the Elevator Centering Screw: 1. -
Page 7: Transmitter And Receiver Binding
Transmitter and Receiver Binding The transmitter comes prebound to the model. If you need to rebind, follow the directions below. Binding Procedure 1. Insert the bind plug in the BND/DAT port on the receiver. 2. Connect the fl ight battery to the ESC. The H menu LED should be fl ashing, indicating the AR7200BX is in bind mode. 3. -
Page 8: Pre-Flight Checklist
❏ Check all wires to ensure that they are not cut, pinched, or chaffed and are ❏ Check to make sure AR7200BX is properly secured properly secured Flying the Blade 450 X • Always keep aircraft in sight and under control • Always let parts cool after use before touching •... -
Page 9: Gyro Gain Adjustment
First fl ights should be performed in normal mode and low cyclic and rudder dual to fl y your aircraft. rates until you are familiar with the fl ying manner of the Blade 450 X. Discover the rates that fi t your fl ying style. -
Page 10: Ar7200Bx Default Blade 450 X Setup
To perform a Blade 450 X AR7200BX factory reset, enter any Setup menu and press the setup button for 10 seconds. After performing the factory reset, you will need to re-center the swashplate servos by using setup menu G. -
Page 11: Ar7200Bx Fine-Tuning And Adjustment
AR7200BX Fine-tuning and Adjustment Observed Behavior Suggested Adjustment Cyclic response too slow or too fast Adjust the control behavior parameter in the AR7200BX to fi t your fl ying style. Control inputs feel delayed Increase Dial 2 on the AR7200BX The helicopter seems to overshoot control input and then return Decrease Dial 2 on the AR7200BX The helicopter tail stops too abruptly Decrease Dial 3 on the AR7200BX... -
Page 12: Limited Warranty
Product in, please use the Horizon Online Service Request submission of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized process found on our website or call Horizon to obtain a Return Merchandise service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Authorization (RMA) number. -
Page 13: Fcc Information
Product(s): Blade 450 X RTF electrical and electronic equipment. The separate collection and Item Number(s): BLH1900, BLH1900M1... -
Page 14: Exploded Views
Exploded View / Explosionszeichnung / Vue éclatée / Vista esplosa... -
Page 16: Parts List
Albero principale senza fl ybar(2): B450 X 17 BLH1908 Yellow Canopy 450X RTF Blade 450X RTF: Kabinenhaube gelb Blade 450 X RTF - Bulle jaune Capottina gialla 450X RTF Bearing 3x6x2.5mm (2): B450 Lager 3 x 6 x 2,5 mm (2): B450 3D/X, Roulement 3x6x2.5mm (2) : B450 3D/X,... - Page 17 Part # English Deutsch Français Italiano Aluminum Motor Mount Set: B450 Aluminium-Motorbefestigungs-Set: Set de fi xations moteur en aluminium : Set montante del motore in allumino: B450 37 BLH1643 3D/X, B400 B450 3D/X, B400 B450 3D/X, B400 3D/X, B400 Sangles crochet et boucle pour ruban Hook &...
-
Page 18: Optional Parts
Optional Parts / Optionale Bauteile / Pièces optionnelles / Pezzi opzionali Part # English Deutsch Français Italiano Blade 450/300x/300CFX: B450/300X/300CFX - Pignon hélicoïdal 11T Pignone elicoidale 11T BLH1903 Helical Pinion 11T B450/300X/CFX Ritzel 11 Z schrägverz. B450/300X/CFX Blade 450/300x/300CFX: Pignone elicoidale 12T BLH1904 Helical Pinion 12T B450/300X/CFX B450/300X/300CFX - Pignon hélicoïdal 12T... - Page 19 Part # English Deutsch Français Italiano Tail Rotor Blade Set, Orange: B450 3D/X, Heckrotorblatt-Set, orange: B450 3D/X, Set de pales d'anticouple, Orange : B450 Set pale del rotore di coda, arancio- BLH1671OR B400 B400 3D/X, B400 ne: B450 3D/X, B400 Tail Rotor Blade Set, Yellow: B450 3D/X, Heckrotorblatt-Set, gelb: B450 3D/X, Set de pales d'anticouple, Jaune : B450 3D/X, Set pale del rotore di coda, giallo:...
- Page 20 ©2014 Horizon Hobby, LLC. Blade, DSM, DSM2, DSMX, Celectra, ModelMatch, AirWare and EC3 are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. BeastX is a registered trademark of Markus Schaack and is used with permission.
Need help?
Do you have a question about the Blade 450 X and is the answer not in the manual?
Questions and answers