Gage Bilt GB703SRVT Installation Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Power Tool
  5. GB703SRVT
  6. Installation manual

Gage Bilt GB703SRVT Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
GB703SRVT
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
e-mail: solutions@gagebilt.com/ www.gagebilt.com
MADE IN U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Gage Bilt GB703SRVT

Summary of Contents for Gage Bilt GB703SRVT

  • Page 1 GB703SRVT INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail: solutions@gagebilt.com/ www.gagebilt.com MADE IN U.S.A.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Description Page Warnings ..........................3 Principle of Operation ......................... 4 How to use the GB703SRVT ........................ 5 Description, Maintenance and Hydraulic Thread Preparation ..........6 Filling & Bleeding ........................7 Troubleshooting ........................8 Overhaul............................ 9 Disassembly and Parts List ..................... 10-11 .....................

  • Page 3: Warnings

    73.2 dB (A). In this daily basis for damage or wear. Any repair should condition the max level was 81.5 dB (A). Therefore, be done by qualified personnel trained on Gage Bilt it is required where prolonged use, hearing procedures.

  • Page 4: Principle Of Operation

    PRINCIPLE OF OPERATION When the lever assy is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool assy causing the air to be redirected. The air is directed to the top of the air piston assy, moving it in a downward direction.

  • Page 5: How To Use The Gb703Srvt

    HOW TO USE THE GB703SRVT WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection and hearing protection be worn during operation. WARNING: Do not pull rivet in the air. Personal injury from fastener ejecting may occur.

  • Page 6: Description, Maintenance And Hydraulic Thread Preparation

    (.68kg)! The entire split handle riveter weighs 11 lbs. (4.99 kg). It has a .780” (19.81mm) rivet setting stroke. The GB703SRVT split handle riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing maximum efficiency.

  • Page 7: Filling & Bleeding

    FILLING & BLEEDING PROCEDURE: NOTE: Air Bleeder Assy (704153) and Fill Bottle (745263) are required. NOTE: To replace a small amount of oil follow BLEEDING steps 5-6. WARNING: Do not cycle tool without air bleeder assy (704153), or the screw and stat-o-seal, installed in tool head. Severe personal injury could result. CAUTION: Before filling handle assy (704132), air piston assy (704121) should be all the way down.

  • Page 8: Troubleshooting

    TROUBLE SHOOTING Providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET. a) Tool needs to be bled. (See filling and bleeding instructions.) b) Spring has fatigued, replace. c) Jaws are stripped or packed with chips.

  • Page 9: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear of tool when installing fastener.

  • Page 10: Disassembly And Parts List

    HEAD WARNING: Dispose of Hydraulic Oil in accordance with applicable regulations. Remove nose assembly and adapter from tool before attempting disassembly of head cylinder assy (703134). Remove end cap (703114). Push against threaded end of piston (703607) to slide it out of head cylinder assy (703134). Be careful not to damage threads or cause burrs on polished piston rod surface.
  • Page 11 HANDLE To inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the manifold-handle (744303) first. For complete disassembly, start by removing base cover (704125). Next, holding tool upright, remove four screws (A-928). Lift manifold-handle (744303) from handle assy (704132) and set aside o'ring (S832) and gasket (704129).

  • Page 12: Dexron® Iii Oil Safety Data

    DEXRON® III OIL SAFETY DATA FIRST AID MEASURES Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material from skin, use soap and water.

  • Page 13: Nose Assembly Selection Chart

    9/14...
  • Page 14 9/14...

  • Page 15: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB703SRVT FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

Table of Contents