Rotor Head Assembly - GAUI Hurricane 425 Assembly Instruction Manual

Rotor Head Assembly 1

請注意
IMPORTANT
1.Join the yoke and center hub,install the
head spacer & damper as shown in figure.
(Fig.1)
將T型頭鎖至鋁軸上並將橡膠環套在圓盤
後利用小起子塞入T型頭兩側。(圖一)
2.Install the parts in that order.(Notice:S -
smaller hole ,L - Larger hole) (Fig.2)
利用橫軸為治具，先套入軸承及止推軸承
(注意:S-小孔，L-大孔)再壓入夾頭內。
(圖二)
3.Assemble grips and yoke tighten the
two screws of spindle shaft (Fig.3)
完成兩個主旋翼夾頭後再以橫軸對鎖。
(圖三)
4.Assemble both of the mixing levers and
join them to the grips. (Fig.4)
組合搖臂並鎖至夾頭上。(圖四)
Main Rotor Yoke Set
#A
#204528
旋翼頭
CNC Main Rotor Yoke
#204676
CNC旋翼頭
CNC Main Rotor Yoke Set
#204628
CNC旋翼頭組
Head Spacer & Damper Set
#B
#204530
橫軸橡皮墊
Ball Bearings Pack(5x11x4)x4
#C
#204563
軸承(5x11x4)x4
Thrust Bearings Pack(5x10x4)x2
#D
#204567
止推軸承(5x10x4)x2
Main Grip Sett
#E
#204529
主旋翼夾頭
CNC Main Grip Set
#204629
CNC主旋翼夾頭
Spindle Spacer & Screw Set
#F
#204615
橫軸螺絲及墊片
Ball Bearings Pack(3x6x2.5)x4
#G
#204560
軸承(3x6x2.5)x4
Mixing Lever Set
#H
#204532
旋翼搖臂
CNC Mixing Lever Set
#204632
CNC旋翼搖臂
Socket head machine
M3X7
1
screws
公制六角螺絲
Washer
W5X9X0.25
2
華司
Self taping screws
2X8
3
粗牙螺絲
請注意
IMPORTANT
Install the seesaw onto the center hub.(Fig.1)
將平衡桿座鎖至鋁軸上。(圖一)
Install the flybar arms onto the flybar.(Fig.2)
將L臂固定在平衡桿上。(圖二)
Make sure the Distance"A" & "B" should be
equal.(Fig.3)
注意平衡桿兩端距離需一致。(圖三)
Seesaw
#A
#204041
平衡桿座
CNC Seesaw Set
#204641
CNC平衡桿座
Flybar Arms Set
#B
#204533
L臂
CNC Stablizer Control Set
#204679
CNC平衡翼控制組
Flybar
#C
#204042
平衡桿
Washer
W3.1X4.6X0.6
1
華司
Bearing
B3X6X2.5
2
軸承
Self taping screws
2X8
3
粗牙螺絲
Machine Screw
M3X6
4
公制螺絲
Socket set screws
M4X4
5
止付螺絲
旋翼頭組立1
CAUTION: Replace the main blades immediately after crash, inspect and replace the
Main Mast / Spindle Shaft / Main Rotor Yoke & Hub if the impact of the crash
damage sthe parts and results in vibration.
警 示:
直昇機遭受撞擊或墜落後應立即更換主旋翼,並應檢查或更換主軸,橫軸及旋翼頭以消除
震動。
#A
Lower pressure on dampers
Middle pressure on dampers
Higher pressure on dampers
#G
5
(Fig.4)
(圖四)
Machine Screw
M3X10
4
公制螺絲
Washer
W3.1X4.6X0.6
5
華司
1
2
#A
2
3
(Fig.1)
(圖一)
P.7
#B
1
2
#C
#F
(Fig.1)
(圖一)
3
#H
4 #B
A = B
A
#C
(Fig.3)
(圖三)
#E
#D
(Fig.2)
(圖二)
#F
(Fig.3)
(圖三)
1
5
(Fig.2)
(圖二)
B
4