Page 1
GAUI Recommendation: We highly suggest using the latest version of the Assembly Instruction Manual. To download the latest version, please visit the Official TSH GAUI web site: www.gaui.com.tw 取得最新的手冊: 我們非常建議您取得最新版本的手冊。 gaui@gaui.com.tw 請到泰世網站下載最新的手冊,並且取代目前的手冊。...
Preface General Maintenance 前言 保養建議 Notices on replacing parts Academy of Model Aeronautics (AMA) 一般拆卸說明 Exploded Views Packing List. Tools and Equipment for Assembly 內容物清單,自備工具 機體分解圖&零件表 General Parts List Assembly Notice, gear ratio, fuselage assembly. 組裝說明,齒輪比,機體組裝 一般零件表 Pre-flight Check 飛行前檢查 Preface Throttle Curve and Pitch Curve P.1 ~ P.2...
GAUI Preface TAI SHIH HOBBY CORPORATION 前言 Thank you for purchasing GAUI X5 High Performance RC Helicopter from Tai Shih Hobby Corporation (TSH). We hope you will enjoy the joy of flight. 感謝您購買泰世科技出品的 GAUI X5高性能遙控直升機,我們希望您可以盡情享受飛行 的樂趣。 In order to understand full assembly sequences, this instruction manual show the assembly information of this model, even though some elements are supplied as pre-assembled.
Page 4
GAUI LIABILITY DISCLAIMER TAI SHIH HOBBY CORPORATION 免責聲明 LIABILITY DISCLAIMER This product is for a radio controlled (RC) helicopter. Improper operation, maintenance or assembly can potentially cause a RC helicopter to pose a danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death.
GAUI Academy of Model Aeronautics (AMA) TAI SHIH HOBBY CORPORATION For United States market, The Academy of Model Aeronautics (AMA) is a national organization representing modelers in the United States. Please refer the National Model Aircraft safety code from Academy of Model Aeronautics.
GAUI TAI SHIH HOBBY CORPORATION Symbols for Assembly Notices 組裝代號說明 Attention: Pay attention, care should be taken Apply general thread lock. Apply special thread lock. during assembly. To tight screw and apply thread lock. To tight screw and apply thread lock.
GAUI Fuselage Assembly TAI SHIH HOBBY CORPORATION 機身組立 a.M3x6 c.M3x6 c.M3x6 b.M3x4 b.M3x4 b.M3x4 c.M3x6 c.M3x6 d.M3x18 e.M3x12 e.M3x12 e.M3x12 1. Complete installation in #B first. Then proceed to install d.M3x18 metal parts to side frame in Upper Servo Mount.
GAUI TAI SHIH HOBBY CORPORATION Fuselage Plates Assembly 機身強化板組立 Before installing, check that the a.M3x6 holes in this aluminum part are pass through hole. b.M3x6 請注意安裝時需確認 #B 為螺絲孔。 c.M3x14 b.M3x6 d.P3x6x4 b.M3x6 a.M3x6 All Screws on side plates should be applied with thread lock.
GAUI TAI SHIH HOBBY CORPORATION Servos Assembly 伺服器安裝 a.M2.6x10 1. Refer (1) to install AIL, PIT a.M2.6x10 servos into fuselage. 2. Refer (2) to install ELE servo to fuselage. 3. Refer (3) to install RUD servo to fuselage. 4. Refer (4) install electronic components to fuselage.
GAUI TAI SHIH HOBBY CORPORATION Motor Assembly - 1 馬達組立 - 1 a.M3x6 b.M3x10 c.M3x3 c.M3x3 c.M3x3 1. Install motor to motor plate with screws M3x6, M3x10 (not locking at this moment), insert 16T motor gear, check position of gear and motor shaft, lock M3x3 screws.
GAUI TAI SHIH HOBBY CORPORATION Assembling Mixing Arms 剪型臂組裝 a.M3x32 d.M3x6 b.W3.1x4.6x0.6 c.N3x5.5L c.N3x5.5L d.M3x6 b.W3.1x4.6x0.6 d.M3x6 #D #E a.M3x32 X5-FES rotor head set should be installed on FES main rotor axis 請注意X5-FES旋翼頭需配合專用FES主軸。 #208850 #208502 #208868 Refer P.19 to assemble Main Blade Grips.
GAUI Checking Servo Travel Direction 伺服機做動方向 TAI SHIH HOBBY CORPORATION 1. Turn on the throttle hold on transmitter. 2. Moving throttle stick upward, all CCPM servos should move upward. 開啟發射機並確認油門為鎖定狀態。 將發射機油門(上)推時CCPM3顆伺服機需同時向上做動並將十字盤上推。 Mode 1 Mode 2 3. Moving throttle stick down, all CCPM servos should move downward.
GAUI Preflight Check TAI SHIH HOBBY CORPORATION 飛行前檢查 1.各部位螺絲是否有確實鎖緊。(1-1.1-2.1-3) 1. Check all screws are tighten firmly. (1-1,1-2,1-3) 2. Check gear mesh between motor gear and main gear are 2.馬達齒是否與主齒盤正確契合 P.9。(1-2) corresponding to each other. P9 (1-2) 3.傳動齒輪間隙是否正確 P.12。(1-2) 3. Check gear mesh between transmission gears. P12 (1-2) 4.電子系統是否確實固定無鬆動。(1-2)
GAUI After Flight Checking TAI SHIH HOBBY CORPORATION 飛行後檢查 1. Check all screws, make sure they are all tightened (not loose). Refer to P.16. ○ 各部位螺絲是否有確實鎖緊無鬆脫(請參考P.16)。 2. Check gear mesh between motor gear and main gear. Inspect any abnormal wear.
GAUI TAI SHIH HOBBY CORPORATION Unpacking and Replacing Main Axis 主軸拆卸說明 1. Unpack #208876 and remove swashplate guide. 2. Remove CCPM control linkages 3. Unpack main gear screw #208864 4. Unpack #208865 screw 5. Remove main rotor head vertically 6. Unpack main rotor head screw #208850 1.卸下#208876並取出滑軌。...
GAUI Disassembling Main Rotors TAI SHIH HOBBY CORPORATION 主旋翼夾頭拆卸說明 Smaller inner race 內徑較小 內徑較大 Bigger inner race #208872 (M3x10) #208341 ① #208874 ② #208751 (M4x10) ② (B6x13x5) #208781 ③ (W6x10x1.5) #208755 ② #208752 (T6x12x4.5) (B6x13x3.5) ① #208874 (M4x10) ② #208781 (W4.1x10x1.4)
GAUI TAI SHIH HOBBY CORPORATION General Parts List 一般零件表 Option / 備品零件 208201 Touch Fastener (Set of 4) 魔鬼氈(白)4個 208202 Cable Tie with Touch Fastener 1x20cm (Set of 6) 魔術束帶 1x20cm(6件組) 208203 Cable Tie with Touch Fastener 20x285cm (Set of 4) 魔術束帶20mmx285mm(4件組)
Page 31
Please refer to official website or contact us for the latest news of GAUI products, the contents or equipments of the products actual packaged product may change and different from this manual. 本說書內的材質、規格,零件包裝之內容物僅供參考組裝用。 泰世科技將不對此印刷物之任何異動更新負責,請以泰世科技公告為主。 謝謝您的愛護與支持。...