Page 1
GAUI V1.2.3 ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION Recommendation: We highly recommand using the latest version of the Assembly Instruction Manual. To download the latest version, please visit the Offi cial TSH GAUI web site: www.gaui.com.tw 取得最新的手冊: 我們非常建議您取得最新版本的手冊。 請到泰世網站下載最新的手冊,並且取代目前的手冊。...
GAUI Preface TAI SHIH HOBBY CORPORATION 前言 Thank you for purchasing GAUI EP255 High Performance RC Helicopter from Tai Shih Hobby Corporation (TSH). We hope you will enjoy the joy of flight. 感謝您購買泰世科技出品的 GAUI EP255 高性能遙控直升機,我們希望您可以盡情享受 飛行的樂趣。 In order to understand full assembly sequences, this instruction manual shows the assembly information of this model, even though some elements are supplied as pre-assembled.
Page 4
GAUI LIABILITY DISCLAIMER TAI SHIH HOBBY CORPORATION 免責聲明 LIABILITY DISCLAIMER This product is for a radio controlled (RC) helicopter. Improper operation, maintenance or assembly can potentially cause a RC helicopter to pose a danger to persons or objects including but not limited to the possibility of causing serious physical injury and even death.
GAUI Academy of Model Aeronautics (AMA) TAI SHIH HOBBY CORPORATION For United States market, The Academy of Model Aeronautics (AMA) is a national organization representing modelers in the United States. Please refer the National Model Aircraft safety code from Academy of Model Aeronautics.
GAUI Symbols for Assembly Notices TAI SHIH HOBBY CORPORATION 組裝代號說明 Attention: Pay attention, care should be taken Apply general thread lock. Apply special thread lock. during assembly. To tighten screw, apply thread lock. To tight screw and apply thread lock.
Page 8
GAUI Front Fuselage Assembly TAI SHIH HOBBY CORPORATION 上前側板組裝 Make sure to assemble the Upper / Apply thread lock on all a.M2x5 Lower Mount at the correct position screws in this section. as shown in Figure. 螺絲均需上止滑劑 b.M2x3.2 組裝伺服機座鋁柱時請注意方向性 Upper Mount c.M1.4x6...
GAUI TAI SHIH HOBBY CORPORATION Front and Back Fuselage Assembly 前後側板組裝 Apply thread lock on all a.M2x3.2 screws in this section. 螺絲均需上止滑劑 b.M1.4x6 Make adjustment to the servo horns with the servo in neutral position. 請在伺服器中立狀態下, 將伺服機舵片組裝完成。 a.M2x3.2 3.5mm 短球頭...
Page 10
GAUI TAI SHIH HOBBY CORPORATION Bottom Fuselage Assembly 下側板組裝 a.B3x6x2 b.M2x3.2 a.B3x6x2 b.M2x3.2 d.M1.4x7 Apply thread lock on all screws in this section. 螺絲均需上止滑劑 b.M2x3.2 b.M2x3.2 d.M1.4x7 d.M1.4x7 d.M1.4x7 GAUI Upper & Lower Fuselage Assembly TAI SHIH HOBBY CORPORATION 上下側板組裝...
Page 11
GAUI TAI SHIH HOBBY CORPORATION Rotor Head Assembly 主旋翼頭組裝 Apply thread lock on all a.W1.4x2.5x0.4 screws in this section. 螺絲均需上止滑劑 b.B1.5x4x1.2 c.M1.4x3 c.M1.4x3 d.O-ring e.P3.1x4.6x1 b.B1.5x4x1.2 a.W1.4x2.5x0.4 a.W1.4x2.5x0.4 f.P1.2x13.5 b.B1.5x4x1.2 g.M1.4x6 c.M1.4x3 Insert the screw from the side without thread.
Page 12
GAUI TAI SHIH HOBBY CORPORATION Washout Arm Assembly 剪型臂組裝 a.Ø1.4x6 b.P1.4x2x3 c.M1.4x6 d.B1.5x4x1.2 e.W1.4x2x0.4 e.W1.4x2x0.4 c.M1.4x6 Apply thread lock on all screws in this section. 螺絲均需上止滑劑 d.B1.5x4x1.2 c.M1.4x6 d.B1.5x4x1.2 a.Ø1.4x6 b.P1.4x2x3 GAUI Swash Plate Assembly TAI SHIH HOBBY CORPORATION 十字盤組裝...
Page 13
GAUI Tail Rotor Base Assembly TAI SHIH HOBBY CORPORATION 尾殼組裝 Apply thread lock on all a.M1.4x4 screws in this section. 螺絲均需上止滑劑 b.W1.4x2.5x0.4 a.M1.4x4 b.W1.4x2.5x0.4 c.B2x7x3 d.B2x5x2.5 c.B2x7x3 e.W2x3.5x1 f.M2x4.6 d.B2x5x2.5 e.W2x3.5x1 Insert belt into pulley of tail rotor shaft and assemble tail rotor shaft as described by exploded view.
Page 14
GAUI TAI SHIH HOBBY CORPORATION Tail Rotor Clamp Assembly 尾旋翼夾頭組裝 Do not over tighten the a.M1.4x5 M1.4x4 screw 鎖緊e.M1.4x4時不可過份鎖緊。 b.W1.4x2x0.5 c.B2x5x1.5 d.P2x3.5x1 g.M1.4x7 e.M1.4x4 a.M1.4x5 b.W2x3.5x0.5 f.P1.4x1.7x2.15 c.B2x5x1.5 d.P2x3.5x1 g.M1.4x7 c.B2x5x1.5 h.M3x3 h.M3x3 e.M1.4x4 Apply thread lock on all screws in this section.
GAUI TAI SHIH HOBBY CORPORATION Belt Direction Check 皮帶方向確認 Make sure both sides of the belt are parallel in the tail boom, turn the front end of the belt 90 degrees counter - clockwise (front view). 安裝尾管總承時請確認皮帶方向無誤 不可纏繞。 GAUI TAI SHIH HOBBY CORPORATION Main Gear Installation 機身主軸組裝...
GAUI TAI SHIH HOBBY CORPORATION Tail Servo Assembly 尾伺服機組裝 a.Ø1.4x4 b.M1.4x6 a.Ø1.4x4 c.M2x3.2 1. Install tail servo and tail boom support rods. Adjust tail servo rod length. 2. Adjust position of servo base (figure 1-1). 3. Adjust position of servo base...
Page 18
GAUI Check - 2 TAI SHIH HOBBY CORPORATION 機構檢查-2 1.Move the throttle stick upward, check and make sure 3 linkages of swashplate all moved upward, if any one of the CCPM servos does not push up the swash plate. Go to the transmitter setting to set Norm/Reverse to set the correct movement.
Page 19
GAUI Check - 3 TAI SHIH HOBBY CORPORATION 機構檢查-3 1.Set the gyro to heading-hold mode, move the rudder stick rightward and make sure the tail pitch slider move towardward to the tail gear case, if it is not, switch the transmitter function “ Servo Reverse ” of “ Rudder” to the opposite position.