Table of Contents
Advertisement
CHAPTER 2 SPECIFICATIONS
2.1 OUTPUT RATING
MODEL
1.Rated output voltage(1*)
2.Rated output current (*2)
3.Rated output power
2.2 AUXILIARY OUTPUTS
1. 15V output (*14)
2. 5V output (*14)
2.3 INPUT CHARACTERISTICS
1.Input voltage/freg. (*3)
2.Maximum
1-Phase, 200Vac models:
Input current
3-Phase, 200Vac models:
at 100% load
3.Power Factor (Typ)
4.Efficiency (*4)
5.Inrush current (*5)
2.4 CONSTANT VOLTAGE MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*7)
3.Ripple and noise (p-p , 20MHz) (*8)
4.Ripple r.m.s., 5Hz~1MHz
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
8.Remote sense compensation/wire
9.
Up-prog. response time, 0~Vomax.(*9)
10.Down-prog. response time
Full load(*9)
No load(*10)
11.Transient response time
12.Hold-up time (Typ)
2.5 CONSTANT CURRENT MODE
1.Max. Line regulation (*6)
2.Max. Load regulation (*11)
3.Load regulation thermal drift
4.Ripple r.m.s. 5Hz~1MHz (*12)
5.Temperature coefficient
6.Temperature stability
7.Warm-up drift
2.6 ANALOG PROGRAMMING AND MONITORING
1.Vout voltage programming
2.Iout voltage programming (*13)
3.Vout resistor programming
4.Iout resistor programming (*13
)
5.On/off control
6.Output current monitor (*13)
7.Output voltage monitor
8.Power supply OK signal
9.Parallel operation
10.Series operation
11.CV/CC indicator
12.Enable/Disable
13.Local/Remote analog control
14.Local/Remote analog indicator
GEN
8-300
10-240
16-150
8
10
16
V
300
150
A
240
2400
2400
W
2400
---
15V 5%, 0.2A Max Load, Ripple & Noise 100mVp-p. Referenced internally to the negative output potential.
K
---
5V 5%, 0.2AMax Load, Ripple & Noise 100mVp-p. Referenced internally ti IF_COM potential.
K
8
10
16
V
Single Phase, 2 Wire +Ground, 200Vac models: 170~265Vrms, 47~63Hz
---
3 Phase, 3 Wire +Ground, 200Vac models: 170~265Vrms, 47~63Hz
17.3
17.3
17.3
A
10.5
10.5
10.5
---
3-Phase models: 0.94 @ 230Vac, 1-Phase models: 0.99 @ 230Vac, rated output power.
%
84
84
86
---
Less than 50A
V
8
10
16
---
0.01% of rated output voltage +2mV
---
0.015% of rated output voltage +5mV
mV
50
50
50
6
6
mV
6
o
O
50PPM/ C from rated output voltage, following 30 minutes warm-up.
PPM/ C
---
0.01% of rated Vout over 8 hrs interval following 30 minutes warm-up. Constant line, load & temp.
---
Less than 0.05% of rated output voltage +2mV over 30 minutes following power on.
V
2
2
2
mS
15
15
15
10
10
20
mS
500
500
500
Time for output voltage to recover within 0.5% of its rated output for a load change 10~90% of rated output
current. Output set-point: 10~100%, Local sense.
mS
Less than 1mS, for models up to and including 100V. 2mS, for models above 100V.
mS
10mSec Typical. Rated output power.
8
10
16
V
---
0.01% of rated output current + 2mA
---
0.02% of rated output current + 5mA
---
Less than 0.05% of rated output current over 30 minutes following load change.
mA
700
500
400
o
70PPM/ C from rated output current, following 30 minutes warm-up.
O
PPM/ C
---
0.01% of rated Iout over 8hrs interval following 30 minutes warm-up. Constant line, load & temperature.
---
8~16V model: Less than +/-0.2% of rated output current over 30 minutes following power on.
20V~600V model: Less than +/-0.1% of rated output current over 30 minutes following power on.
---
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-0.5% of rated Vout.
---
0~100%, 0~5V or 0~10V, user selectable. Accuracy and linearity: +/-1% of rated Iout.
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1% of rated Vout.
---
0~100%, 0~5/10Kohm full scale, user selectable. Accuracy and linearity: +/-1.5% of rated Iout.
---
By electrical Voltage: 0~0.6V/2~15V or dry contact, user selectable logic.
---
---
0~5V or 0~10V, user selectable. Accuracy: +/-1%.
---
0~5V or 0~10V, user selectable. Accuracy : +/-1%.
---
4~5V-OK, 0V-Fail. 500ohm series resistance.
---
Possible , up to 4 units in master/slave mode with two wires current balance connection.
---
Possible (with external diodes), up to 2 units. 600Vdc max.from chassis ground.
---
Open collector. CC mode: On, CV mode: Off. Maximum voltage : 30V, maximum sink current: 10mA
---
Dry contact. Open: Off, Short: On. Max. voltage at Enable/Disable in: 6V.
---
By electrical signal or Open/Short: 0~0.6V or short: Remote, 2~15V or open: Local.
---
Open collector. Local: Open, Remote: On. Maximum voltage: 30V, maximum sink current: 10mA.
20-120
30-80
40-60
60-40
20
30
40
60
120
80
60
40
2400
2400
2400
2400
20
30
40
60
16.6
16.8
16.6
16.6
10.2
10.1
10.1
10.1
88
86
86
88
30
40
20
60
55
55
60
50
6
6
6
6
2
5
5
5
15
15
20
30
20
20
20
30
500
600
700
1100
30
20
40
60
250
150
90
60
10
10
80-30
100-24
150-16
300-8
80
100
150
300
30
24
16
8
2400
2400
2400
2400
80
100
150
300
16.6
16.6
16.6
16.6
10.1
10.1
10.1
10.1
88
88
88
88
80
100
150
300
60
70
90
150
7
10
45
20
5
5
5
5
40
40
60
80
50
50
80
100
1200
2500
1500
3000
80
100
150
300
40
30
12
10
600-4
600
4
2400
600
16.6
10.1
87
600
240
60
5
100
100
3000
600
5
Advertisement
Table of Contents
