Stopping Or Restarting Your Dryer; Lock Controls; Drying And Cycle Tips - Kenmore 110.C8756 Series Use & Care Manual

I Adjust Dryness Level and/or Options.
NOTE: Dryness Level selections can be made only while
using Auto Cycles. Selecting More, Normal or Less
automatically adjusts the sensed time needed.
Auto Dry cycles take the guesswork out of drying time
and enhance fabric care. The amount of time that is
displayed is the estimated time remaining in the cycle.
To use a Timed Cycle
I Select a Timed Cycle.
I
Press MORE TIME or LESS TIME until the desired drying
time is displayed. Tap MORE TIME or LESS TIME, and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME, and the time will change by
5-minute intervals.
NOTE: The Timed Cycle Adjust features can be used only
with Timed Cycles.
I Press TEMPERATURE until the desired temperature
illuminates.
To make changes to Time and/or Options during a Timed
Cycle:
I Press STOP once.
I
Adjust the Time and/or Options.
5. (OPTIONAL STEP) If desired, select WRINKLE GUARD
more details, see "WRINKLE GUARD
6. (OPTIONAL STEP) The Cycle Signal is preset to on. If desired,
you may turn the Cycle Signal off.
7. Press and hold START for approximately 1 second until dryer
starts. Be sure the door is closed.
I
If you do not press Start within 5 minutes of selecting a
cycle, the dryer automatically shuts off.
® . For
® 90."

Stopping or Restarting Your Dryer

To pause/stop the dryer at any time
Open the door or press STOP once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
To end/cancel your dryer at any time
Press STOP twice or open the door.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.

Lock Controls

This feature allows you to lock your settings to prevent
unintended use of the dryer. You can also use the control lock
feature to prevent unintended cycle or option changes during
dryer operation.
To enable the control lock feature:
Press and hold the CYCLE SIGNAL button for 3 seconds. The
CONTROLS LOCKED icon lights up, and a single beep tone is
heard. To unlock, press and hold the CYCLE SIGNAL button for
3 seconds. The indicator light turns off.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your
load. If an Auto Cycle is running, the display shows the estimated
cycle time, which is determined by your dryer automatically
sensing the dryness level of your load. If a Timed Cycle is
running, the display shows the exact number of minutes
remaining in the cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
I Follow care label directions when they are available.
I
If desired, add a fabric softener sheet. Follow package
instructions.
I To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits, and synthetic fabrics.
I
Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
I
Dry most loads using the preset cycle settings.
I Refer to the Auto Cycles or Timed Cycles Preset Settings
chart (in the "Cycles" section) for a guide to drying various
loads.
I Drying temperature and Dryness Level are preset when
you choose an Auto Cycle. You can select a different
dryness level, depending on your load, by pressing
Dryness Level and choosing More or Less.
NOTE: You cannot use the Timed Cycle Adjust and you
cannot modify temperature with the Auto Dry cycles.
I
If you wish to adjust the cycle length of a Timed Cycle,
press More Time or Less Time. Adjust the temperature of
a Timed Cycle by pressing TEMPERATURE until the
desired temperature is selected.
NOTE: You cannot use the Dryness Level with Timed
Cycles.
15