Page 1
Assembly and Operating Manual 3D SU‐26 Specification: *Length: 27‐2/5"(695mm) *Wing Span: 29‐3/5"(750mm) *Flying Weight: 16‐9/10 oz (480g)
Page 2
The receiving system is powered by the speed Integral wing panels with L.H / R.H. ailerons and SKYANGEL 3D Aerobaticrange and thank you for controller’s integral BEC system. servos placing your trust in us.
Page 3
Assembly and Operating Manual 3D SU-26 Fig. 1 -Tighten the control rod in vertical tail with screw. Fig. 2 - Photo shows the finished view Fig. 3 -Tighten the control rod in horizon tail with screw. Fig. 4 - Photo shows the finished view...
Page 4
Assembly and Operating Manual 3D SU-26 Fig. 5 -Tighten the control rod in wing set with screw. Fig. 6 -Photo shows the finished view Fig. 7 -Reverse the procedure to the left wing. The photo shows the finished view. Fig. 8...
Page 5
Assembly and Operating Manual 3D SU-26 Figs. 9 -Apply glue to the position which will assemble horizon tail. Figs. 10 -Photo shows the finished view Figs. 11 -Assemble the taildraggers to the hole in the fuselage Figs. 12 -Assemble the taildraggers to the steering part...
Page 6
Assembly and Operating Manual 3D SU-26 Figs. 13 -Apply glue to vertical tail . Figs. 14 -Glue the steering part to vertical tail. (Glue not included) Figs. 15 -Assemble the vertical tail to fuselage. Figs. 16 - Photo shows the taildraggers assembled on the...
Page 7
Assembly and Operating Manual 3D SU-26 Figs. 17 -Connect the vertical tail pushrod collet to control rod arm. Figs. 18 - Photo shows the finished view. Figs. 19 -Connect the horizon tail pushrod collet to control rod arm. Figs. 20...
Page 8
Assembly and Operating Manual 3D SU-26 Figs. 21 -Connect the wing panel push rod to the servo arm at first hole. Figs. 22 -Connect the wing panel push rod to control rod arm. Figs. 23 -Photo shows the finished view.
Page 9
Assembly and Operating Manual 3D SU-26 Figs. 25 -Assemble the wing panel to fuselage Figs.26 -Tight the fixup presser with screw. Figs. 27 -Photo shows the finished view . Figs. 28 - Assemble the landing gear to the fuselage.
Assembly and Operating Manual 3D SU-26 Figs. 29 -Photo shows the finished view. Figs. 30 -Assemble the propeller base to the motor shaft. Figs. 31 - Assemble the propeller to the motor shaft. Figs. 32 -Tight the propeller with screw.
Assembly and Operating Manual 3D SU-26 Figs. 33 -Assemble the plastic spinner to the motor shaft. Figs. 34 -Tight the plastic spinner with screw. Figs. 35 -Photo shows the finished view. Figs. 36 -Connect to the receiver and place the receiver in the...
Page 12
Assembly and Operating Manual 3D SU-26 Figs. 37 -Assemble the battery cover to the fuselage. Figs. 38 -Photo shows the finished view. Fig. 39 Balancing - Place the canopy on the fuselage. - Place the battery in the model of balancing; do not connect it.
Assembly and Operating Manual 3D SU-26 Figs. 40 -Charge the flight battery; connect the Equalizer lead using and adapter lead matching your charger (adapter lead not included).. Figs. 41 -Switch the transmitter on, and move the throttle stick to the “Motor OFF” position. (Diagram MODE 1...
Page 14
Assembly and Operating Manual 3D SU-26 Figs. 42-43 - Check the channel assignment of the control surfaces, and swap over the connectors at the - Check the neutral position of the control surfaces. Make adjustments to the clevises if necessary.
Assembly and Operating Manual 3D SU-26 - Switch the transmitter on, and connect the Test-flying, flying notes - With the motor running at full-throttle, give the flight pack aeroplane a firm launch directly into any breeze, Read the sections in the Safety - Check the direction of rotation of the motor: with the fuselage and wings level.
Need help?
Do you have a question about the 3D SU-26 and is the answer not in the manual?
Questions and answers