Overhead Rigging - JB Systems LASER BURST II Operation Manual

ENGLISH
 This product is a so-called show laser, emitting radiation with a wavelength spectrum between 400 and
700 nm and producing lighting effects for shows.
 Due to the construction of this laser, the beam is moved so fast, that it can only hit the eye very short. This
is why the use of this laser for a Laser-Light-Show can be regarded as save.
 Never direct the laser beam to people or animals and never leave this device running unattended.
 This laser may only be used for shows. The operation of a class 3B show laser is only allowed if the
operation is controlled by a skilled and well-trained operator.
 Depending on the classification, operating a laser product can produce laser radiation that may cause
permanent eye damage and/or skin damage. The legal instructions for using a laser product vary from
country to country. The user must always inform himself on the legal instructions valid in his country and
apply them to his situation.
Please note that JB SYSTEMS cannot be made liable for damages caused by incorrect installations and
unskilled operation!
DESCRIPTION:
1. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
2. ON/OFF KEY ACTUATED SWITCH: used to switch the unit on/off. Use the keys to make sure only a
skilled operator is able to switch the laser on.
3. INTERNAL MICROPHONE: The built-in microphone is used to synchronize the laser show to the beat of
the music.
4. DMX INPUT: 3pin male XLR-connector used to connect universal DMX-cables. This input receives
instructions from a DMX-controller.
5. DMX OUTPUT: 3pin female XLR-connector used to connect the LASER BURST with the next unit in the
DMX chain.
6. DISPLAY: shows the selected DMX address when the unit is in DMX-mode. Apart from DMX-mode you
can also select 4 other working modes, see further to learn more about these modes.
7. CONTROL PANEL: Used to select the different functions of the laser, see further to learn how to
operate the unit.
8. REMOTE CONTROLLER INPUT: Input for the CA-8 remote hand controller, see further for more
information on this issue.
9. SAFETY EYE: used to attach a safety cable when the unit is rigged (see paragraph "overhead rigging"
10. MUSIC INPUT SENSITIVITY: This potentiometer is used to adjust the music input sensitivity. Turn the
potentiometer until the laser works in sync with the music.
JB SYSTEMS
®
USER MANUAL
3/47 LASER BURST II
ENGLISH
11. COOLING FAN: used to cool the components inside the
enclosure. Make sure to never cover this fan outlet!
12. INTERLOCK input: used to connect the optional emergency stop
switch (see picture). When you push this switch the laser beam will
disappear immediately.
IMPORTANT! For your own safety we strongly recommend to
connect this optional switch!
13. POWER LED: indicates that the unit is switched on.
14. SOUND LED: flashes to the sound of the music detected by the internal microphone.
15. HANGING BRACKET: with 2 knobs on both sides to fasten the unit and a mounting hole to fix a
mounting hook.
16. LASER OUTPUT: Here the laser beam leaves the enclosure, make sure to NEVER look inside the unit
through this opening while the laser effect is switched on!
17. WARNING LABEL: "Caution – Class 3B laser. Laser Radiation when open. Avoid exposure to beam."
18. WARNING LABEL: "Laser Aperture"
19. LASER WARNING SIGN: warns against a potentially dangerous laser when not used by skilled
operators.
20. WARNING LABEL: "Laser Radiation. Avoid exposure to beam. Class 3B laser product"

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
JB SYSTEMS
®
USER MANUAL
4/47 LASER BURST II