Maintenance; Operating Instructions - JB Systems LED-UV212 black light Operation Manual

ENGLISH
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display inversion) or
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to show the number of working hours in the display.
 Press the MENU button for about 2 seconds to return to running mode.
Software version:
Used to show the software version of the unit.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to show the software version of the unit.
 Press the MENU button for about 2 seconds to return to running mode.

OPERATING INSTRUCTIONS

A. Standalone 1unit:
 Just connect the projector to the mains and put on some music. The unit starts working automatically
to the rhythm of the music.
 Refer to chapter HOW TO SETUP to learn how to switch between static and sound mode.
Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
 Connect 2 to maximum 16 units together. Refer to the chapter "electrical installation" to learn how to
do this.
 Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music. Refer to chapter HOW TO SETUP for more information.
Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
BUTTON
STANDBY To blackout all the fixtures
1.Synchronous strobe
FUNCTION
2.Two light strobe
Strobe
MODE
(LED OFF)
D. Controlled by universal DMX-controller:
 Connect all units together. Refer to the chapter "Electrical installation for two or more units in DMX-
mode" to learn how to do this (don't forget to address all units properly!)
 Connect all units to the mains and turn on the DMX controller.
Since each unit has its own DMX-address, you can control them individually. Remember that each unit
uses 1 or 2 DMX-channels as shown in the DMX chart below:
JB SYSTEMS
®
OPERATION MANUAL
(normal display).
ACTIONS
Adjust dimmer level
from 000 to 255
Color select
(LED ON)
7/45 LED-UV212
ENGLISH

MAINTENANCE

 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
JB SYSTEMS
®
OPERATION MANUAL
8/45 LED-UV212