Canon dp-v3010 Instruction Manual
Canon dp-v3010 Instruction Manual

Canon dp-v3010 Instruction Manual

Video display
Hide thumbs Also See for dp-v3010:

Advertisement

Quick Links

Video Display

Instruction Manual

• Before use, be sure to read this guide, including the
safety and handling precautions.
• Reading this guide will help you learn to use the video
display properly.
• Store this guide safely so that you can use it in the future.
English

Advertisement

Table of Contents
loading

Summary of Contents for Canon dp-v3010

  • Page 1: Video Display

    Video Display Instruction Manual • Before use, be sure to read this guide, including the safety and handling precautions. • Reading this guide will help you learn to use the video display properly. English • Store this guide safely so that you can use it in the future.
  • Page 2: Table Of Contents

    Table of Contents Introduction ..........................4 About this manual ............................ 4 Trademarks .............................. 4 Safety Precautions ........................5 Handling Precautions ........................6 Features ............................8 Supplied Accessories ......................... 10 Nomenclature ..........................11 Main Unit ..............................11 Display Controller ........................... 13 Installation/Connection ......................
  • Page 3 OSD Menu ..........................35 OSD Menu Index ............................ 35 Adjustment ............................. 40 Channel Settings ............................ 49 Display Settings ............................51 Marker Settings ............................54 Function Settings ........................... 59 System Settings ............................. 64 Signal Information ........................... 68 System Information ..........................68 Main specifications/Performance ....................
  • Page 4: Introduction

    Introduction Thank you for purchasing the Video Display DP-V3010. The On Screen Display (thereafter referred to OSD) default language setting is English. To change the OSD menu language setting, please refer to p. 64. About this manual Some of the illustration used in the manual have been simplified for clarity. Conventions used in this manual : Indicates a reference page. Note: Indicates a note. Reference: Indicates reference information. CAUTION: Indicates an item you must observe. Trademarks • DisplayPort and VESA are registered trademarks or trademarks of Video Electronics Standards Association in the U.S and other countries. • Other product and company names herein are trademarks or registered trademarks of their respective owners. Introduction...
  • Page 5: Safety Precautions

    For the customers in the U.S.A. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment. Use of shielded cable is required to comply with class A limits in Subpart B of Part 15 of FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canon U.S.A Inc. One Canon Park, Melville, NY 11747, U.S.A. Tel No. (631)330-5000 For the customers in Canada CAN ICES-3 (A) / NMB-3 (A) For the customers in Europe Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands Only for European Union and EEA (Norway, Iceland and Liechtenstein) This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU) and national legislation. This product should...
  • Page 6: Handling Precautions

    Handling Precautions Places to avoid using the video display Do not use the video display in the following places or conditions. • Places with excessive dust or humidity • Places that will expose the video display to direct sunlight, smoke (such as from a kerosene heater or other such source) or steam • Near heat sources, humidifiers or flammable gas • Near a window during rain or snow • Near water or other places that could cause moisture to form on the video display Screen Handling • The screen may be damaged if it is exposed directly to strong light source. Please take precautions when placing it near a window. • Do not press firmly on the screen, scratch it or place an object on the screen. It can cause non-uniformity or damage to the panel. • The screen and cabinet may become warm during use. Note this does not constitute a malfunction. About Backlight The backlight has a limited service life so its brightness may degrade and color may change due to aging. About Temporary Screen burn-in If a stationary image is displayed for a prolonged period, screen burn-in may occur where you see remnants of what was displayed. This is a characteristic of LCD and is not a failure. However, this is only temporary and will disappear when playing video.
  • Page 7 Cleaning • Before cleaning, please unplug the power plug from the wall outlet. • The screen has a special surface treatment, avoid touching it directly with your hand. In addition, never affix adhesive objects such as seals. • Never use alcohol or benzene, thinner, acidic cleaning solution, alkaline cleaning solution, abrasive or chemical wipes because these will damage the screen. • If the screen is dirty, wipe gently with soft dry cloth such as cleaning cloth or eye glasses cleaning cloth. Wiping the screen too hard may cause unevenness on the screen or damage the LCD panel. The screen may be scratched if wiped too hard with a cleaning cloth with foreign particles attached. • When the screen is extremely dirty, wipe with soft cloth such as cleaning cloth or eye glasses cleaning cloth moistened with water-diluted neutral detergent. • Use a blower to remove dust from the surface of the screen. • Since the cabinet around the screen has a special surface treatment, wiping off the area may fade its surface color. • Wipe dirt on cabinet with a soft cloth. If the screen is very dirty, use a moistened cloth with water or mild detergent diluted with water. Do not use alcohol, benzene, paint thinner, or pesticides as they may damage the surface finish or erase characters on the cabinet. Disposing • Do not dispose together with normal waste. Do not include the video display in waste that will be taken to landfill. • Observe the rules and regulations of your local authorities when disposing. Handling Precautions...
  • Page 8: Features

    Features DP-V3010 video display is packed with the essence of Canon's image-making know-how such as high-definition IPS LCD panel, display engine and backlight technology. It provides optimal performance and functions in the field of video production such as color grading and VFX (Visual Effects). Faithful Color Reproduction The display features a Canon-designed RGB LED backlight system and IPS LCD panel which reproduce a rich array of colors. Besides the DCI (Digital Cinema Initiatives) color gamut, it is also ideally suited to displaying the color gamuts of a multiple number of other broadcast standards, namely, ITU-R BT.709, ITU-R BT.2020, EBU, SMPTE-C and Adobe RGB. High-Resolution/High Definition 4K content is displayed dot-by-dot with 10.5 megapixels resolution (4096x2560) and 157.5 μm pixel pitch. High Contrast DCI-P3 standard contrast ratio of 2000:1 or greater is achieved by adopting image processing technology implemented through the use of high contrast panel and Canon's proprietary algorithm. Aspect Ratio Suitable for Video Production (16:10) The aspect ratio enables dot-by-dot display of digital cinema (1.896:1) or HDTV broadcast (16:9) contents for color grading work, as well as display standard PC signal (16:10) in full, which is ideal for VFX work. 2K/Full-HD High Definition View Canon's proprietary algorithm reduces jagged lines and produces smooth display when expanding 2K/Full-HD content. Specialized Performance and Functions for Video Production Display • Use with other Canon equipment...
  • Page 9 • Calibration without a PC Calibration can be performed easily without the use of dedicated application. Calibration enables brightness and color to maintain factory default settings. You can also adjust the video display condition to match your requirements, purpose, and the ambient light. • Operability All settings are possible with display controller operation. Minimum necessary operations are also possible from the main unit, providing means of operation depending on the use cases. Other • Functions to check videos Equipped with functions including Peaking, False Color, Wave Form Monitor, Vector Scope, Zoom, Screen Capture and other markers. • Supported interfaces – E quipped with 3G/HD-SDI terminal that is standard in the broadcast industry and DisplayPort terminal used in PC with high resolution. – E quipped with a USB terminal for connecting a controller for color grading (element-Tk by Tangent Wave Ltd), an external sensor for calibration or a USB memory device. • Multiple Format Support Supports 1280x720 / 24.00P, 25.00P, 30.00P, 50.00P, 60.00P to 4096x2160 / 24.00P, 25.00P, 30.00P, 48.00P, 50.00P, 60.00P, 50.00i, 60.00i SDI and 640x480 to 4096x2560 DisplayPort signals to enable viewing of a variety of signal. • Equipment Design Enabling Effective Use of Space The space-saving installation against a wall is possible thanks to the proprietary heat dissipation. Features...
  • Page 10: Supplied Accessories

    Supplied Accessories The following items are supplied with this product. Please check before using. AC Power Cord VT-20 Display Controller CL-01 LAN Cable LN-30 (3 m) Compact Power Adapter Rack Mount Bracket RB-01 Rack Mount Bracket Screw SW-02 CA-PS700 and AC cable (M3 x 6 mm x 4) Hex Key HK-01 Tip Prevention Fitting TP-01 (Allen wrench 3 mm) (M6 x 10 mm x 2) Instruction Manual Disc* DP-V3010 Instruction Manual (this document) * I nstruction Manual Disc This disc contains the Japanese, English, French, German, and Simplified Chinese instruction manuals in PDF format. Adobe Reader 11.0 or above must be installed on your computer to view the instruction manuals in PDF format. Supplied Accessories...
  • Page 11: Nomenclature

    Nomenclature Main Unit ■ Front F1 to F4 button Executes the defined function. The following functions have been assigned at the factory. These functions can be changed if necessary. F1: Channel UP F2: Channel DOWN F3: Time Code (On/Off) F4: Aspect Marker (On/Off) button (Power button) Turns power On/Off. Power indicator Displays the status of the main unit. The brightness of the power indicator can also be set from "1 (dark) to 5 (brightest)". Even when the power indicator is "Off", it will flash during firmware update, network settings reset, or when an error is detected. Off: main power supply "Off" Green lit: main power supply "On"/Power "On" Green flash: d uring calibration, firmware update, network settings reset in progress, or paring with the display controller Amber lit: standby (Main power supply "On" and power supply "Off") Amber flash: when error is detected ■ Rear Main power supply Turns main power supply On/Off. switch Handle Use for carrying the main unit. – AC power input terminal Connects the supplied AC power supply cord. Nomenclature...
  • Page 12 ■ Interface Left side Right side LAN (10/100 Connects to display BASE) terminal controller. 7A a 3G/HD-SDI input Two input systems The main unit connects terminal 1 corresponding to input 1. 1 to 1 with the display 8A s 3G/HD-SDI Monitor output controller. It can also be output terminal 1 corresponding to 7A a connected via a hub. 9A d 3G/HD-SDI input Two input systems USB port Used to connect an terminal 2 corresponding to input 2. external sensor for calibration ( 31), USB A q A f 3G/HD-SDI Monitor output memory, hub, or controller output terminal 2...
  • Page 13: Display Controller

    Display Controller ■ Front 1 F1-F10 buttons Executes the assigned function. 2 RGB select button (when using CDL) Selects and adjusts RGB during CDL adjustment. 3 SHARPNESS knob (normal use) Adjusts the sharpness of the Provides the same control as the Image. buttons in the OSD menu. POWER knob (when using CDL) Adjusts the gamma of the image. 4 CHROMA knob (normal use) Adjusts the color saturation of the Provides the same control as the image. buttons in the OSD menu. SATURATION knob (when using CDL) 5 BRIGHTNESS knob (normal use) Adjusts the black level of the image. OFFSET knob (when using CDL) 6 CONTRAST knob (normal use) Adjusts the white level of the image. SLOPE knob (when using CDL) 7 CDL select switch Switches between normal and CDL mode. 8 RESET button Returns adjustments 3 to 6 to default value. When adjusting the values using the slider in the OSD menu, press the RESET button above SHARPNESS or CHROMA to return to the default value.
  • Page 14 ■ Rear (lid opened) A f LAN terminal Connects the main unit to the display controller using a LAN cable. A g DC IN terminal Connects to compact power adapter CA-PS700. Nomenclature...
  • Page 15: Installation/Connection

    Installation/Connection CAUTION • When unpacking, carrying, installing, or connecting the main unit, please note that at least two people are required. • Do not touch or damage the screen during installation and connection. How to Carry the Main Unit Please carry the main unit as illustrated in the figure below. CAUTION • Do not pick up the main unit by the handle only. Please take particular care as the main unit may tilt and cause injury or get damaged, when carried. Handle Preventing from Tipping The supplied tip prevention fitting TP-01 can be used to significantly reduce the risk of the main unit tipping or falling. Make sure to complete the power and input device connections beforehand. CAUTION • When securing the main unit to a stand, please ensure the stand is strong enough to support the weight of the main unit. • Do not move the main unit after it is secured. 1. Remove two top screws at the rear of the main unit using the supplied hex key HK-01. Do not lose the removed screw. Do not use these screws for other purposes.
  • Page 16: Connecting The Main Unit To Input Devices

    2. Insert the tip prevention fitting TP-01 into the two top screw holes and secure. Screw holes 3. Pass a safety strap through the ring of the tip prevention fitting TP-01 and secure to the wall or stand. Connecting the Main Unit to Input Devices This main unit has four inputs which correspond to a display area. The display area icons located in the input terminal area shows where the input video is displayed on the screen. Please ensure these are connected correctly as indicated by the icons.
  • Page 17 ■ 4K or QFHD signals input through SDI Displays using 4 inputs. 3G/HD-SDI Dual Link HD-SDI 3G/HD-SDI supports two input systems. Input Link A signal to input 1, Link B signal to input 2. Input 3G/HD-SDI 1 to input 1, Input 3G/HD-SDI 2 to input 2 ("Input Configuration" 49). Area B Area A (3G/HD-SDI 1) (3G/HD-SDI 1) Area A Area B Area B Area A (3G/HD-SDI 2) (3G/HD-SDI 2) Area C Area D (3G/HD-SDI 1) (3G/HD-SDI 1) Area C Area D Area D Area C (3G/HD-SDI 2) (3G/HD-SDI 2) ■ 2K or Full-HD signals input through SDI Displays using 1 input. To center the displayed content, select "Channel Settings"→"Select Input Signal"→"Single Input"...
  • Page 18 ■ 4K or QFHD signals input through DisplayPort Displays using 4 inputs. Area B Area A Area D Area C ■ 2K or Full-HD signals input through DisplayPort Displays using 1 input. To center the displayed content, select "Channel Settings"→"Select Input Signal"→"Single Input" and select the area to display from A to D ( 49). Area A When connecting with the DisplayPort cable, use the cable with the following wiring specifications. DisplayPort male DisplayPort male DisplayPort male DisplayPort male 1 ––––––––––––––––––– 12 11 ––––––––––––––––––– 2 2 ––––––––––––––––––– 11 12 ––––––––––––––––––– 1 3 ––––––––––––––––––– 10 13 ––––––––––––––––––– 13 4 –––––––––––––––––––...
  • Page 19: Connecting The Main Unit To The Display Controller

    Connecting the Main Unit to the Display Controller This section describes how to connect the main unit to the display controller. CAUTION • When using a commercially available LAN cable, please use a shielded type cable no longer than 3 m in order to prevent malfunction due to noise. 1. Open the lid on the back of the display controller. While holding the display controller with one hand, place your finger in the cutout portion of the lid and pull forward. Cutout 2. Connect the supplied LAN cable LN-30 and the compact power adapter CA-PS700. Insert the connector of the LAN cable LN-30 and plug of the compact power adapter CA-PS700 as shown in the figure below. Use the cutout section to pass the cables, as illustrated.
  • Page 20: Installing The Display Controller On The Rack

    Installing the Display Controller on the Rack The display controller can be installed on an EIA standard compliant 19-inch rack. CAUTION • Make sure that the display controller does not fall during installation/removal. 1. Place the display controller on the rack mount bracket RB-01 as shown in the figure and match the screw holes. Make sure the cable does not get caught in the rack mount bracket during installing. Display Controller (Back side) Rack Mount Bracket RB-01 (Back side) Rack Mount Bracket Screw SW-02 Rack Mount Bracket Screw SW-02 2.
  • Page 21: Mounting The Main Unit On A Stand Or Wall

    Mounting the Main Unit on a Stand or Wall This main unit can be fitted to a stand* or to a wall mount bracket*. Screws compatible with this main unit are M6 x 10 mm (VESA Standard 200 x 200 mm). * Commercially available. CAUTION • Make sure to perform this step, with at least two people. • When mounting the main unit on a wall, make sure the wall has sufficient strength. If necessary, apply reinforcement. Also, make sure to check the load capacity of the stand or wall mount bracket. • Make sure that the main unit does not fall during installation/removal. 1. Remove four screws at the rear of the main unit using the supplied hex key HK-01. Do not lose the removed screw. Do not use these screws for other purposes. Screws 2. Mount the main unit on a stand or wall mount bracket. Installation/Connection...
  • Page 22: Turning On The Power

    Turning on the Power This section describes how to turn on the power of the main unit. Turning on the Power of the Main Unit 1. Plug the AC power cord VT-20 to the power supply input terminal at the rear of the main unit. 2. Turn on the main power supply switch ( I ) at the back. The main unit goes into standby and the power indicator flashes amber.
  • Page 23: Pairing

    Pairing To operate the main unit using the display controller, the main unit needs to be registered (paring) to the display controller. Pairing the Main Unit with the Display Controller 1. Connect the main unit to the display controller ( 19). 2. Turn on the power of the main unit ("Turning on the Power of the Main Unit" 22). This automatically completes pairing and the power indicator of the main unit flashes green and the power indicator of the display controller also lights green.
  • Page 24: Re-Pairing

    Re-pairing To pair a display and the display controller again for example when a paired display controller is reconnected. 1. Connect the main unit to the display controller ( 19). 2. Enable communication between the main unit and the display controller. Reset the network settings of the main unit. To reset the pairing information, press and hold the main unit's F3 and F4 buttons simultaneously for about 3 seconds until the power indicator flashes green. "Configure an IP Address" is set to "Automatic". Reset the network settings of the display controller. To reset the pairing information, press and hold the display controller's buttons, and SET buttons simultaneously for about 3 seconds until the power indicator flashes green. "Configure an IP Address" is set to "Automatic". "Display List" is also reset.
  • Page 25: Operating The Display Controller

    Operating the Display Controller The display controller allows you to easily adjust the input signal settings and image quality. In addition, you can assign the frequently used functions to dedicated buttons. Adjusting the Image Quality 1. Adjust the image quality by rotating each knob. Use the slider that appears at the bottom of the screen as guide. • SHARPNESS Adjusts the sharpness of the image. • CHROMA Adjusts the color saturation of the image. • BRIGHTNESS Adjusts the black level of the image. • CONTRAST Adjusts the white level of the image. Adjusting the Image Quality on CDL 1. Switch the CDL select switch to CDL. 2.
  • Page 26: Temporarily Saving Parameters (Anchor Point Setting)

    Temporarily Saving Parameters (Anchor Point Setting) Temporarily saves parameters while adjusting SHARPNESS, CHROMA, BRIGHTNESS, and CONTRAST allows you to 45 for setting anchor points during CDL adjustment. bring those parameters back. See for setting anchor points during CDL adjustment. 1. Press the MENU button to open the OSD menu. 2. Select "Adjustment" with the buttons and press the SET button. The selection frame moves to sub menu. 3. Select "Anchor Adjustment" with the buttons and press the SET button. When the confirmation screen appears, select "OK". The parameter is saved and sets anchor point.
  • Page 27: Using The Channel (Ch) Button

    Using the Channel (CH) Button You can assign channels (various settings related to input signal) to the CH buttons on the display controller and switch channels instantly. 1. Press the MENU button to open the OSD menu. 2. Select "System Settings"→"Function/Channel Button"→"Controller Channel" and press the SET button. A new window opens and displays button names CH1 to CH4. 3. Select a button name with the buttons and press the SET button. The selection frame moves to next OSD menu level.
  • Page 28: Using The Osd Menu

    Using the OSD Menu You can access the OSD menu from the display controller. Basic Operation Top Screen 1. Press the MENU button to open the OSD menu. Sub Menu Setting Options Main Menu 第 1 階層 第 2 階層 第 3 階層 2. Select an item with the buttons and press the SET button.
  • Page 29: Adjusting Image Quality While Viewing The Entire Image

    Adjusting Image Quality While Viewing the Entire Image You can adjust the OSD menu to display as a slider at the bottom of the screen. This allows for the image quality to be adjusted whilst it is displayed on the screen. 1. Press the SET button when the selection frame is on setting options. A slider appears at the bottom of the screen. 2. Use the slider as guide and adjust with buttons. 3. Press the SET button when finished. The screen returns to the original OSD menu.
  • Page 30 ■ Adjusting "x, y" under "Color Temperature" You can adjust "x, y" in "Color Temperature" on the color map. Default value Last used value Current value Current value 1. Adjust "x" with the button and "y" with button. The adjusted value is indicated by the " " mark on the color map. You can adjust "x" using the POWER knob on the display controller and "y" using the SATURATION knob. 2. When adjustments are completed, press the SET button. The screen returns to the original OSD menu. Using the OSD Menu...
  • Page 31: Calibration Without A Pc

    Calibration without a PC ( When "User 1-7" under "Picture Mode" is selected, you can perform calibration using an external sensor, without using the computer. The supported external sensors are Konika Minolta Display Color Analyzers CA-310 and CA-210. Be sure to also read the instruction manual of the CA-310 and CA-210. 1. Connect the display color analyzer to the USB port of the main unit. 2. Open the OSD menu and select "Adjustment"→"Detail Settings"→"Calibration". Set each target value. 3. Select "Start" with the SET button. Please follow the information indicated on the screen.
  • Page 32: Export/Import

    4. Select the file type of the LUT. Select the file type of the LUT by using "Gamma" or "Color Gamut". 5. In "Select LUT", select the destination to save the file. Select User LUT 1-8. 6. Select the standard color gamut. Select the color gamut used when creating the LUT (when "Color Gamut" under "LUT Type" is selected). 7. Select "Execute". When the confirmation screen appears, select "OK". Import starts. Note • The LUT file is proprietary to Canon Video Display. Refer to the Canon website for the file format and how to create. • Up to 1000 LUT import files are recognized. • You can delete the imported LUT. You can specify the name of LUT ( 45). Using the OSD Menu...
  • Page 33 ■ Export/Import Main Menu Settings ( 1. Press the MENU button to open the OSD menu. 2. Select "System Settings"→"Export/Import". 3. Select "Export" or "Import". Exporting 1 Select "Target" from "USB" or "User 1-3". Export "USB" to the USB memory and "User 1-3" to the built-in memory of the main unit. 2 Select "Filename". Factory default is "dinfo.dat". You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols. 3 Select "Execute". When the confirmation screen appears, select "OK". Export starts. Importing 1 Select "Target" from "USB" or "User 1-3". Specify the destination to save the file to be imported. 2 Select "Filename".
  • Page 34: Set Date/Time

    Set Date/Time ( This section describes how to set the Date/Time. The Date/Time of this video display will be reset if the main power is turned off for about 20 days. 1. Press the MENU button to open the OSD menu. 2. Select "System Settings"→"Date/Time". A screen to input the Date/Time appears. 3. Press the buttons to move the selection frame. Use the buttons to change the numeric value. Repeat until you complete setting the year, month, date, hour, and minute. 4. Press the SET button when you are finished. The selection frame moves to "OK".
  • Page 35: Osd Menu

    OSD Menu OSD Menu Index Adjustment ( Picture Mode Contrast Brightness Chroma Sharpness Backlight Control Color Temperature Color Gamut Gamma HDR Range ODT Surround Color Range CDL Preset Power Saturation Offset Slope CDL Bypass Detail Settings CDL Export CDL Import CDL Preset Name Anchor CDL Reset CDL Detail Settings LUT Import LUT Name LUT Delete YCbCr Color Matrix 2020 Gamut Mapping Calibration Copy Picture Mode Picture Mode Name Anchor Adjustment Reset OSD Menu...
  • Page 36 Channel Settings ( Select Channel Input Configuration Select Input Signal Format Internal Sync Channel Name Picture Mode Color Range Display Settings ( Screen Scaling Zoom Scaling Method Frame Hold Background Color I/PsF I/P Conversion Film Cadence Marker Settings ( Marker Preset Aspect Marker Enable Mask Aspect Ratio Line Line Width Line Color Line Brightness H Position V Position Safety Zone Marker 1, 2 Enable Aspect Ratio Area Size Rate (%) Width (dot) Height (dot) Shape Line Width OSD Menu...
  • Page 37 Line Color Line Brightness H Position V Position Area Marker Enable H Position V Position Width (dot) Height (dot) Mask Line Line Width Line Color Line Brightness Center Marker Enable Size Line Width Line Color Line Brightness Grid Marker Enable Distance Line Width Line Color Line Brightness Function Settings ( Peaking Enable (Peaking 1/Peaking 2/Off) Monochrome Frequency Range Color False Color Screen Capture Capture Frame Hold Capture Source Playback File Finish Playback File OSD Menu...
  • Page 38 Time Code Enable Type Size Position Wave Form Monitor Enable Select Signal Display Type Select Line Position Guide Standard Level High Standard Level Low Color Vector Scope Enable Target Position Test Pattern Various Function Monochrome, Blue Only, Red Off, Green Off, Blue Off, H Delay, V Delay, Banner, Function Guide, OSD Position, OSD Size, Black Level Control, Backlight Scan System Settings ( Network Language Function/Channel Button Display Function Controller Function Controller Channel Display Name Date/Time Power Indicator Brightness Compatible Settings Firmware Update Protect Settings Password Protect Target Protect Controller Settings Knob Lock Display List OSD Menu...
  • Page 39 Export/Import Export Import Power on Setting Reset All Settings Signal Information ( Channel Input Configuration Select Input Signal Format Resolution Picture Rate, I/P/PsF SDI Payload ID Video Standard Sampling Structure Bit Depth Picture Rate Scanning Method Link Number Horizontal Frequency Vertical Frequency Pixel Encoding Color Depth Matrix RGB Range System Information ( Display Model Name Display Serial No. Display Firmware Ver. Display Usage Time Display IP Address Display Subnet Mask Display MAC Address Display Controller Model Name Display Controller Serial No. Display Controller Firmware Ver. Display Controller IP Address Display Controller Subnet Mask Display Controller MAC Address OSD Menu...
  • Page 40: Adjustment

    Adjustment This menu is used to adjust the image quality and perform calibration without a PC. Item Setting Options (underline indicates factory default) Picture Mode Select a preset mode. See 47 for each setting. SMPTE-C, EBU, ITU-R BT.709, ITU-R BT.2020, Adobe RGB, DCI-P3: Mode set to the brightness, color temperature, gamma, and color gamut of the three primary colors chromaticity points of each standard. User 1-7: Custom modes. Set each item of "Adjustment". You can change the mode name within 16 one-byte characters including alphabetical characters, numbers, and symbols. Canon Log: Canon Log is ideal when viewing image captured with CINEMA EOS SYSTEM camera/ video camera. Performs linear conversion and displays Canon Log video without having to import Viewing LUT. ACESproxy: This mode is used to display ACESproxy (ACES 0.7/1.0) videos with the optimum gamma and color gamut. The version of ACESproxy can be selected from "Compatible Settings" under "System Settings". Contrast Adjusts the white level of the image. (Increments of 1) 0 to 2000 Brightness Adjusts the black level of the image. (Increments of 1) -500 to 500 Chroma Adjusts the color saturation of the image (color depth). (Increments of 1) 0 to 2000 Sharpness Adjusts the sharpness of the image. (Increments of 1) 0 to 100 Backlight Control Switches the backlight control method.
  • Page 41 Cinema Gamut to 709, Cinema Gamut to 2020, Cinema Gamut to DCI, DCI-P3+ to 709, DCI-P3+ to DCI, DCI-P3 to 709, ITU-R BT.2020 to 709: Modes where the color gamut is converted to monitor Cinema Gamut, DCI-P3+, ITU-R BT.2020, and DCI-P3 videos recorded by the Digital cinema camera of the CINEMA EOS SYSTEM ACESproxy: Displays the color gamut of ACESproxy when "Canon Log" is selected. User LUT 1-8: Selects an external LUT. Note • To check a video recorded using a CINEMA EOS SYSTEM digital cinema camera, refer to the "Parameter of Cinema EOS System and DP-V3010 ( 48). • When "ITU-R BT.2020", "Cinema Gamut to 709", "Cinema Gamut to 2020", "Cinema Gamut to DCI", "DCI-P3+ to 709", "DCI-P3+ to DCI", "DCI-P3 to 709", or "ITU-R BT.2020 to 709" is selected, the DP-V3010 displays images after converting the color gamut as shown below. Data outside of the color gamut after conversion is also displayed at the optimum level. Input video color gamut Color gamut after conversion on the DP-V3010 ITU-R BT.2020...
  • Page 42 Item Setting Options (underline indicates factory default) Gamma Sets the Gamma. 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, Canon Log, Canon Log 2: Select the preset gamma. Canon Log (HDR), Canon Log 2 (HDR), SMPTE ST 2084: Select the gamma for HDR display. User LUT 1-8: Selects an external LUT. The relationship between "Color Gamut" and "Gamma" that can be selected is shown below. When "Color Gamut" is changed, gamma is changed to the underlined value (default value) only when current gamma value is not selectable. Picture Mode Color Gamut Selectable Gamma SMPTE-C Cannot be selected 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, Canon Log,...
  • Page 43 Item Setting Options (underline indicates factory default) HDR Range Setting is enabled when "Canon Log (HDR)", "Canon Log 2 (HDR)", or "SMPTE ST 2084" is selected for "Gamma". Canon Log (HDR): Sets the dynamic range to be displayed from 0 to 800% that "Canon Log" has. (in 100 increments) 100 to 800% Canon Log 2 (HDR): Sets the dynamic range to be displayed from 0 to 1600% that "Canon Log 2" has. (in 100 increments) 100 to 1600% SMPTE ST 2084: Sets the dynamic range to be displayed from 0.005 to 10,000 nit that "SMPTE ST 2084" has. (in 100 increments) 100 to 4000 nit (2000)  Setting procedures The procedures below use Canon Log (HDR) as an example. When the maximum value (800%) is specified, the 800% dynamic range of Canon Log is assigned to the dynamic range of the video display. Although the brightness in appearance lowers, you can...
  • Page 44 Black level: 64 (10-bit)/256 (12-bit) White level: 1023 (10-bit)/4095 (12-bit) Note • When "1.0" is selected for "ACES", under "Compatible Settings", it can be used except when "ACESproxy" is selected for "Picture Mode" or "ACESproxy" is selected for "Color Gamut". • Operations when "Automatic" is selected are described below. When DisplayPort is selected, "Full (0-255)" or "Limited 1 (16-235)" is set automatically depending on DisplayPort signal information. When SDI is selected, the setting is configured according to the settings for Picture Mode, Color Gamut, and Gamma. Picture Mode Color Gamut Gamma Color Range to be Set DCI-P3 – – Full (0-255) Canon Log, User 1-7 DCI-P3, Cinema Gamut to DCI, – DCI-P3+ to DCI Other than the above Other than the Canon Log, Limited 2 (16-255) above Canon Log 2 Other than the Limited 1 (16-235) above Canon Log (HDR), Full (0-255) – – Canon Log 2 (HDR), SMPTE ST 2084...
  • Page 45 Item Setting Options (underline indicates factory default) Configures settings for CDL. CDL files created on Canon Video Display can also be used because the file type is the same. CDL Preset Sets CDL preset. Imported LUT can also be set as preset. CDL 1-15, User LUT Note • When "User LUT" is selected, all "CDL" items, "Chroma", and "Blue Only" cannot be changed. • When a CDL value has been adjusted, "*" is displayed with the title of CDL Preset. • CDL values do not return to the factory default even after the power is turned On/Off or the channel is changed. Power Adjusts the gamma of the image. (in 0.01 increments) 0.50 to 4.00 (1.00) Saturation Adjusts the color saturation of the image. (in 0.001 increments) 0.000 to 2.000 (1.000) Offset Adjusts the black level of the image. (in 0.001 increments) -1.000 to 1.000 (0.000) Slope Adjusts the white level of the image. (in 0.001 increments)
  • Page 46 Matrix Automatic: Matrix coefficient is set in conformance with the ITU-R BT.2020 standard when the "Picture Mode" or "Color Gamut" setting is "ITU-R BT.2020" and in conformance with the ITU-R BT.709 standard otherwise. ITU-R BT.709: Matrix coefficient is set in conformance with the ITU-R BT.709 standard. ITU-R BT.2020: Matrix coefficient is set in conformance with the ITU-R BT.2020 standard. 2020 Gamut Set this item when "ITU-R BT.2020" is selected for "Picture Mode" or when "User 1-7" or "Canon Mapping Log" is selected for "Picture Mode" and also "ITU-R BT.2020" is selected for "Color Gamut". Gamut Mapping: Mapping is performed on colors outside the native color gamut by Canon's unique method. Clipping: Colors outside the native color gamut are clipped by a general method. Calibration Performs calibration based on set target values when "User 1-7" is selected for "Picture Mode". Luminance: Sets the target luminance. 48 to 200 cd/m Color Temperature: Sets the target color temperature. D93, D65, D61, D60, D56, D50, DCI-P3: Select from preset color temperatures. Custom (xy): You can adjust CIE x, y in increments of 0.001. x: 0.260 to 0.360 (0.314)/y: 0.260 to 0.360 (0.351) Color Gamut: Sets the color gamut.
  • Page 47 CDL Preset CDL 1 CDL 2 CDL 3 CDL 4 CDL 5 YCbCr Color Matrix Automatic Automatic Automatic Automatic Automatic 2020 Gamut Mapping Gamut Mapping Gamut Mapping Gamut Mapping Gamut Mapping Gamut Mapping User Item DCI-P3 Canon Log ACESproxy Contrast 1000 Brightness Chroma 1000 1000 1000 1000 Sharpness Local Dimming Middle Middle Middle Middle Color Preset...
  • Page 48 Parameter of Cinema EOS System and DP-V3010 Cinema EOS System DP-V3010 Color Color Gamma Color Gamut Gamma Color Range Space Temperature BT.709 Canon Log ITU-R BT.709 Canon Log Automatic BT.2020 ITU-R BT.2020 Cinema Cinema Gamut to 709 Gamut Cinema Gamut to DCI-P3 DCI-P3 DCI-P3+ DCI-P3+ to 709 DCI-P3+ to DCI-P3 DCI-P3 BT.2020 Canon Log 2 ITU-R BT.2020 Canon Log 2 Cinema Cinema Gamut to 709 Gamut Cinema Gamut to DCI-P3 DCI-P3...
  • Page 49: Channel Settings

    Channel Settings This menu is used for input related settings. Select the "Select Channel" item and choose a channel number from CH1 to CH30. Finally define the parameter of each of the "Channel Settings". Item Setting Options (underline indicates factory default) Select Channel Displays the channel number. In addition, you can assign each content of "Channel Settings" to each channel ( 50). CH1 to CH30 Note • It may take 10 seconds when switching channels. Input Configuration Select the input. Factory default depends on the channel ( 50). 3G/HD-SDI 1, 3G/HD-SDI 2, Dual Link HD-SDI, DisplayPort, — (Not set) Select Input Signal Sets the signal display method ( 16). Automatic: "4K Input" and "Single Input" are automatically determined. 4K Input: Displays the signal transmitted over four inputs. Single Input: Displays the signal of a single input onto the center of the screen. Select from A to D. Format Sets the color format and gradation.
  • Page 50 Black level: 64 (10-bit)/256 (12-bit) White level: 1023 (10-bit)/4095 (12-bit) Note • When "1.0" is selected for "ACES", under "Compatible Settings", it can be used except when "ACESproxy" is selected for "Picture Mode" or "ACESproxy" is selected for "Color Gamut". • Operations when "Automatic" is selected are described below. When DisplayPort is selected, "Full (0-255)" or "Limited 1 (16-235)" is set automatically depending on DisplayPort signal information. When SDI is selected, the setting is configured according to the settings for Picture Mode, Color Gamut, and Gamma. Picture Mode Color Gamut Gamma Color Range to be Set DCI-P3 – – Full (0-255) Canon Log, User 1-7 DCI-P3, Cinema Gamut to DCI, – DCI-P3+ to DCI Other than the above Other than the Canon Log, Limited 2 (16-255) above Canon Log 2 Other than the Limited 1 (16-235) above Canon Log (HDR), Full (0-255) – – Canon Log 2 (HDR), SMPTE ST 2084 The factory default settings for each channel is shown in the following table.
  • Page 51: Display Settings

    Display Settings This menu is used to configure the display method. Item Setting Options (underline indicates factory default) Screen Scaling Defines how the video is scaled and displayed on the screen. Native Input Resolution: Displays the input signal without scaling. 1920x1080 (original) 200%: Doubles the vertical and horizontal dimensions. 1920x1080→3840x2160 Automatic: Enlarges to full screen. 1920x1080→4096x2304 Note • Even if "Automatic" is selected, the magnification is up to 200% in the following cases: When "Peaking 1" or "Peaking 2" is selected When "False Color" is "On" • In the case of SDI signal, when "H Delay"/"V Delay" is "On", "Screen Scaling" is fixed to "Native Input Resolution". Zoom When the resolution is 4096x2560, 4096x2160 or 3840x2160, the enlarged image is displayed at the center of the screen or at the position selected screen of a 4-screen layout. Center, Top Left, Top Right, Bottom Left, Bottom Right, Off Left Top Right Top Center...
  • Page 52 Item Setting Options (underline indicates factory default) Scaling Method Sets the interpolation method when "Screen Scaling" is set to "200%" or "Automatic". Shape Trace: Canon original processing that produces smooth slopes with reduced jagged lines. Bicubic: General interpolation process that uses neighboring pixel information to create interpolated pixels. Nearest Neighbor: Process that uses nearest neighbor pixel information to create (copy) new pixels. This is useful as it enlarges the original pixels, thus making any jagged lines visible. Note • In the case of SDI signal, setting is disabled when "H Delay" or "V Delay" is "On". Frame Hold Pauses the video. On, Off Note • Setting is disabled when "Peaking 1" or "Peaking 2" is selected. • Setting is disabled when "False Color" is set to "On". Background Color Sets the color of the black band to check the boundary of the black band and video image. White, Gray, Off Note • Setting is disabled when "Peaking 1" or "Peaking 2" is selected. I/PsF Defines how the interlace signal or PsF signal is displayed. Automatic: Automatically determined based on payload and displayed. If there is no payload, the signal is displayed as an interlace signal.
  • Page 53 Item Setting Options (underline indicates factory default) Film Cadence Sets the film cadence mode. 2-2: Displays progressive image after conversion for 2-2 pulldown processed interlaced signal input. 2-3: Displays progressive image after conversion for 2-3 pulldown processed interlaced signal input. 2-3-3-2: Displays progressive image after conversion for 2-3-3-2 pulldown processed interlaced signal input. Off: Does not perform film cadence mode progressive conversion. Note • This can be set only when "I/P Conversion" is set to "Image Priority". OSD Menu...
  • Page 54: Marker Settings

    Marker Settings This menu is used to configure various markers. Item Setting Options (underline indicates factory default) Marker Preset Customizes markers which are assigned to markers 1 to 5. Marker 1 to 5, Off Aspect Marker An aspect marker displays a range in accordance with the specified aspect ratio. Note • In the case of SDI signal, setting is disabled when "H Delay" or "V Delay" is "On". • Aspect marker is not displayed in the following cases: When there is no signal, unsupported signal, or a channel with "Input Configuration" not set is selected When an enlarged image is displayed During the execution of "Playback File" under "Screen Capture" When "H Delay" or "V Delay" is "On" When a "Test Pattern" is displayed When "Peaking 1" or "Peaking 2" is selected Enable Switches the aspect marker On, Off. On, Off Mask Switches the mask color. Mask is the blanking area outside the range of the marker. Black: Half (50% gray): Off: Turns mask off. Note • Because the Wave Form Monitor, Vector Scope and Time Code appear under the Mask, a part of them is hidden by the Mask.
  • Page 55 Item Setting Options (underline indicates factory default) Line Width Sets the thickness of the aspect marker line. Thick, Normal, Thin Line Color Sets the color of the aspect marker line. White, Red, Green, Blue, Yellow, Cyan, Magenta Line Sets the brightness of the aspect marker line. Brightness High, Low H Position Changes horizontal position without changing the aspect. -65 to 65 (0) V Position Changes vertical position without changing the aspect. -35 to 35 (0) Safety Zone Marker 1, 2 There are two types of safety zone marker: 1 and 2, which share the same settings. A safety zone marker is used to set the safe zone of the image (actual displayed area) to check the image. Note • In the case of SDI signal, setting is disabled when "H Delay" or "V Delay" is "On". • Safety zone marker is not displayed in the following cases: When there is no signal, unsupported signal, or a channel with "Input Configuration" not set is selected...
  • Page 56 Item Setting Options (underline indicates factory default) Height (dot) Becomes active when you select "Variable (dot)" under the menu "Area Size". Move the slider to set the area height in 2 dot increment. 240 to 2560 (1728) Shape Sets the area shape of the safety zone marker. Box: Brackets: Enclosure: Line Width Sets the width of the safety zone marker line. Thick, Normal, Thin Line Color Sets the color of the safety zone marker line. White, Red, Green, Blue, Yellow, Cyan, Magenta Line Sets the brightness of the safety zone marker line. Brightness High, Low H Position Adjusts the marker horizontal position with the set aspect and size. -65 to 65 (0) V Position Adjusts the marker vertical position with the set aspect and size.
  • Page 57 Item Setting Options (underline indicates factory default) Area Marker "Area Marker" is used to check a specific area using a rectangular box. Note • In the case of SDI signal, setting is disabled when "H Delay" or "V Delay" is "On". • "Area Marker" is not displayed in the following cases: When there is no signal, unsupported signal, or a channel with "Input Configuration" not set is selected When an enlarged image is displayed During the execution of "Playback File" under "Screen Capture" When "H Delay"/"V Delay" is "On" When a "Test Pattern" is displayed When "Peaking 1" or "Peaking 2" is selected Enable Switches the area marker On, Off. On, Off H Position Sets the start position (x-coordinate) to draw the rectangle (in increments of 2). 0 to 4086 (240) V Position Sets the start position (y-coordinate) to draw the rectangle (in increments of 2). 0 to 2550 (120) Width (dot) Sets the width of the rectangle (in increments of 2). 10 to 4096 (240) Height (dot) Sets the height of the rectangle (in increments of 2).
  • Page 58 Item Setting Options (underline indicates factory default) Center Marker The center marker shows the center of the image. Note • "Center Marker" cannot be displayed when a zoomed image is displayed. • "Center Marker" cannot be displayed when "Peaking 1" or "Peaking 2" is selected. Enable Switches the center marker On, Off. On, Off Size Sets the size of the center marker. Large, Small Line Width Sets the width of the center marker line. Thick, Normal, Thin Line Color Sets the color of the center marker line. White, Red, Green, Blue, Yellow, Cyan, Magenta Line Sets the brightness of the center marker line. Brightness High, Low Grid Marker Grid markers are markers used to check the horizontal and vertical position.
  • Page 59: Function Settings

    Function Settings This menu is used to display, define and apply various functions. Item Setting Options (underline indicates factory default) Peaking Customizes peakings which are assigned to Peaking 1 or Peaking 2. The outline is displayed in a color, used to check the focus. Note • "Peaking" cannot be displayed during the execution of "Playback File" under "Screen Capture". • In the case of SDI signal, setting is disabled when "H Delay" or "V Delay" is "On". Enable Switches the peaking display mode and also sets peaking to Off. Peaking 1, Peaking 2, Off Configures detailed settings for "Peaking 1" or "Peaking 2". Monochrome: Displays video in monochrome. On, Off Frequency: Sets the central frequency of contour enhancement signals. Peaking 1 (Low, Middle, High), Peaking 2 (Low, Middle, High) Range: Sets the width of the range to be colored.
  • Page 60 Item Setting Options (underline indicates factory default) Playback File Plays back captured images. Select File: Selects a file. Execute: Plays back the image. Note • When playing back captured images on other DP-V3010 or PC, color may not be played back precisely. Finish Finishes playback. Playback File Time Code Display the time code superimposed on the SDI signal. Note • "Time Code" is not displayed in the following cases: When an enlarged image is displayed When "Frame Hold" is set to "On" When "Peaking 1" or "Peaking 2" is selected During the execution of "Playback File" under "Screen Capture" When a "Test Pattern" is displayed Enable Switches the time code display On, Off. On, Off Type Selects the type. VITC, LTC Size Selects the size. Large, Small Position Selects the display position.
  • Page 61 Item Setting Options (underline indicates factory default) Wave Form Monitor Wave Form Monitor is displayed for SDI signals. On the wave form monitor, the horizontal axis shows the horizontal resolution of the video and the vertical line shows the signal level. 100% Signal level Horizontal resolution of video Note • "Wave Form Monitor" is not displayed in the following cases: When "Frame Hold" or "False Color" is "On", When "Peaking 1" or "Peaking 2" is selected During the execution of "Playback File" under "Screen Capture" When a "Test Pattern" is displayed When "H Delay"/"V Delay" is "On" • When "Wave Form Monitor" is "On", "Vector Scope" is "Off". Enable Switches the wave form monitor On, Off. On, Off Select Signal Sets the wave form to be displayed. Y, Cb, Cr, R, G, B Display Type Sets the display type. When "Line" is selected, data for one line is displayed. All, Line Selects the line to be displayed when "Line" is selected. Select Line: 1 to 2160 Position Selects the display position.
  • Page 62 Item Setting Options (underline indicates factory default) Vector Scope Vector Scope is displayed for SDI signals. Vector scope displays the intensity of color signals and hue with the horizontal axis showing the color difference signal Cb and the vertical line showing Cr. (Cb, Cr) = (255, 255) Magenta Yellow Blue Green Cyan (Cb, Cr) = (0, 0) Note • "Vector Scope" is not displayed in the following cases: When "Frame Hold" or "False Color" is "On", When "Peaking 1" or "Peaking 2" is selected During the execution of "Playback File" under "Screen Capture" When a "Test Pattern" is displayed When "H Delay"/"V Delay" is "On" • When "Vector Scope" is "On", "Wave Form Monitor" is "Off". Enable Switches the vector scope On, Off. On, Off Target Sets the target. 75%, 100% Position Selects the display position. Bottom Left, Bottom Right Test Pattern Sets the test pattern built into the main unit.
  • Page 63 Item Setting Options (underline indicates factory default) Various Function Displays the function list to execute functions. Monochrome (On, Off), Blue Only (On, Off), Red Off (On, Off), Green Off (On, Off), Blue Off (On, Off), H Delay (On, Off), V Delay (On, Off), Banner (On, Off)* Function Guide (On, Off)* , OSD Position (Mode 1 (4096x2560), Mode 2 (3840x2160))* OSD Size (Large, Small)* , Black Level Control (On, Off)*...
  • Page 64: System Settings

    System Settings This menu is used to set the settings related to the main unit and display controller system. Item Setting Options (underline indicates factory default) Network Sets the main unit and display controller network settings. Note • Setting is disabled when "Power on Setting" is set to "User 1-3". Configure an IP Automatic: Configures an IP address automatically with DHCP/Automatic IP. Manual: Configure an IP address and subnet mask manually. Address Display 192.168.0.1 Display 192.168.0.10 Controller Subnet Mask 255.255.255.0 Language Sets the language of the OSD menu and messages. English, Function/Channel Button Sets the function or channel to assign to the F buttons or CH button. Display Function Sets the function to assign to the F buttons of the main unit. Select an F button and assign a function from the list ( 67). The factory defaults for the main unit F buttons is as follow: F1 : Channel UP F2 : Channel DOWN F3 : Time Code F4 : Aspect Marker Note • When changing channels with "Channel UP/DOWN", the channels with "Input Configuration"...
  • Page 65 Item Setting Options (underline indicates factory default) Display Name Sets the name of the main unit. You can input up to 16 alphanumeric characters. Date/Time Sets the year/month/date/hour/minute. Power Indicator Brightness Adjusts the brightness of the power indicator on the main unit. 5 is the brightest. Off, 1 to 5 (2) Compatible Settings Sets the version of ACESproxy. 0.7, 1.0 ACES Firmware Update This function is used to update the video display firmware. Refer to the Canon website for detailed information. Protect Settings Locks the settings so they cannot be changed. When you press the MENU button, "Signal/System Information" appears, but other operations are grayed out because they are locked. • Unlocking Protect Settings Move the selection frame to "Protect Settings" and press the SET button for approximately 3 seconds. When a password has been set, enter the password and select "OK". Password Set a password to protect settings. Use a four-digit number (0000 to 9999). Protect Target You can remove Picture Mode and Select Channel from the items to be protected. Picture Mode: Select "On" to protect or "Off" to exclude settings for "Picture Mode". On, Off Select Channel: Select "On" to protect or "Off" to exclude settings for "Select Channel".
  • Page 66 Item Setting Options (underline indicates factory default) Export/Import Sets the export/import main menu settings. Note • The following settings cannot be exported or imported. Adjustment Target values of Calibration (including calibration results) Display Settings Zoom, Frame Hold Function Settings Test Pattern, Various Function (Monochrome, Blue Only, Red Off, Green Off, Blue Off, H Delay, V Delay) System Settings Date/Time, Export/Import, Power on Setting • Data exported from this product may not be imported to products of which firmware version is earlier than the version of this product. To import data, update the firmware to the latest version. Export Target: Select the export destination. USB: Export to a USB memory User 1-3: Export to the built-in memory of the main unit Filename: Factory default is "dinfo.dat". You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols. Execute: Performs export. Import Target: Specify the destination to save the file to be imported. USB, User 1-3 Filename: Displays files with the extension ".dat" so you can select from among them. Settings (All, Adjustment, Channel Settings, Display Settings, Marker Settings, Function Settings, System Settings): Select the settings to import.
  • Page 67 Options Item Options Adjustment Picture Mode CDL Preset SMPTE-C CDL Bypass CDL Export/Import ITU-R BT.709 CDL Save to Memory ITU-R BT.2020 CDL Load from Memory Adobe RGB Channel Settings Channel UP DCI-P3 Channel DOWN User 1-7 Select Input Signal Canon Log Display Settings Screen Scaling ACESproxy Zoom Backlight Control Scaling Method Gamma Frame Hold Background Color HDR Range Marker Settings Marker Preset Gain Aspect Marker Bias Safety Zone Marker 1 Safety Zone Marker 2 Color Gamut SMPTE-C...
  • Page 68: Signal Information

    Matrix sRGB Bit Depth 10-bit RGB Range Full Picture Rate 24.00 Scanning Method Progressive/Progressive (Transport/Picture) Link Number Single/Link_1 * When a content is grayed out, an asterisk "*" may be displayed indicating low "Picture Rate" accuracy such as "24.00P *". System Information Shows the video display status and network information. Item Display Example Display DP-V3010 Serial No. 000000000000 Firmware Ver. 1.20 Usage Time* IP Address 192.168.0.1 Subnet Mask 255.255.255.0 MAC Address FF:FF:FF:FF:FF:FF Display Controller CL-01 Serial No. 00000000 Firmware Ver. 4.0.0 IP Address 192.168.0.10...
  • Page 69: Main Specifications/Performance

    Main specifications/Performance Main Unit Panel Panel Type IPS LCD panel Screen Size 30 inch (76.1 cm) Aspect Ratio 16:10 Resolution 4096x2560 (10.5 megapixels) Active Display Area Approximately 645.1 x 403.2 mm Pixel Pitch 157.5 μm Panel Driver 1024 gradations, 10-bit for each RGB color Image quality Brightness (Standard) 48 cd/m (DCI-P3), 100 cd/m View Angle (Up, Down, Left, Right) 89° (contrast ratio 10 : 1 or higher) Surface Treatment Low-Reflection Glare General Backlight Type RGB LED, direct down type Power Rated Voltage: 100 – 240 V AC Rated Frequency: 50/60 Hz Power consumption At maximum load (including change in brightness through aging): Approximately 370 W At factory shipment: Approximately 130 W Environmental Operating Temperature and humidity: 5 – 35 °C (41 – 95 °F), 20 – 80 %RH (no condensation) Conditions recommended: 15 – 30 °C (59 – 86 °F) Pressure: 700 – 1060 hPa...
  • Page 70: Display Controller

    Interface Control USB A receptacle port Universal Serial bus specification revision 2.0 compliant LS (Low Speed)/FS (Full Speed)/HS (High Speed) mode compatible Enhanced host controller interface specification revision 1.0 compliant 1 RJ-45 terminal IEEE802.3 10BASE-TX / IEEE802.3u 100BASE-TX compliant Display Controller General Power Rated Voltage: 100 – 240 V AC Rated Frequency: 50/60 Hz Power consumption At maximum load: Approximately 2 W At factory shipment: Approximately 2 W Environmental Operating Temperature and humidity: 5 – 35 °C (41 – 95 °F), 20 – 80 %RH (no condensation) Conditions Storage/Transporting Temperature and humidity: - 20 – 40 ˚C (-4 – 104 °F), 10 – 85 %RH (no condensation) 41 – 60 ˚C (105 – 140 °F), 10 – 40 %RH (no condensation) Dimensions (width x height x depth) Approximately 419 x 56 x 88 mm (16.5 x 2.2 x 3.5 in.) Weight Approximately 460 g (16.2 oz) Mounting Hole Pitch EIA2U standard 76.2 x 465.9 mm (3.0 x 18.3 in.) Interface Control 1 RJ-45 terminal Weight and dimensions are approximate. Error and omissions excepted. The information in this manual is verified as of September 2015.
  • Page 71: Dimensions

    Dimensions ■ Main Unit 189 (7.4) 708 (27.9) 30 (1.2) 30 (1.2) 80 (3.1) (18.3) (13.3) 350 (13.8) 4-M6 200 (7.9) (18.7) (7.9) * Without protruding parts (3.0) Unit: mm (inch) ■ Display Controller 56 (2.2) 419 (16.5) (1.5) (3.5) Unit: mm (inch) ■ Other accessories (Rack Mount Bracket RB-01) 483 (19.0) 465.9 (18.3) 10.3 (0.4)
  • Page 72: Appendix

    Appendix Supported Signal Format ■ SDI Transmission method Signal format Color format Color depth Standards HD-SDI x 1 1280x720P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 296 1280x720P 50.00 Hz 1280x720P 29.97/30.00 Hz 1280x720P 25.00 Hz 1280x720P 23.98/24.00 Hz 1920x1080i 59.94/60.00 Hz SMPTE 292-1 SMPTE 274M 1920x1080i 50.00 Hz 1920x1080P 29.97/30.00 Hz 1920x1080PsF 29.97/30.00 Hz 1920x1080P 25.00 Hz 1920x1080PsF 25.00 Hz 1920x1080P 23.98/24.00 Hz 1920x1080PsF 23.98/24.00 Hz 2048x1080i 59.94/60.00 Hz 2048x1080i 50.00 Hz 2048x1080P 29.97/30.00 Hz SMPTE 292-1 SMPTE 428-9 2048x1080PsF 29.97/30.00 Hz SMPTE 428-19 2048x1080P 25.00 Hz...
  • Page 73 Transmission method Signal format Color format Color depth Standards HD-SDI Dual x 1 1920x1080P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 372 SMPTE 274M 1920x1080i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 50.00 Hz 4:2:2 YCbCr 10-bit 1920x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 25.00 Hz...
  • Page 74 Transmission method Signal format Color format Color depth Standards HD-SDI Dual x 1 2048x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 372 SMPTE 428-9 SMPTE 428-19 4:4:4 X'Y'Z' 12-bit SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 372 SMPTE 2048-2 4:2:2 YCbCr 12-bit 2048x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 372 SMPTE 2048-2 4:2:2 YCbCr 12-bit 2048x1080P 25.00 Hz 4:4:4 RGB 12-bit/10-bit...
  • Page 75 Transmission method Signal format Color format Color depth Standards 3G-SDI Level A x 1 1920x1080P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 274M 1920x1080i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 4:4:4 YCbCr SMPTE 274M 4:2:2 YCbCr 12-bit 1920x1080P 50.00 Hz 4:2:2 YCbCr 10-bit 1920x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080PsF 29.97/30.00 Hz 4:4:4 RGB 10-bit 12-bit 4:4:4 YCbCr...
  • Page 76 Transmission method Signal format Color format Color depth Standards 3G-SDI Level A x 1 2048x1080P 50.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 2048-2 2048x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:4:4 X'Y'Z' 12-bit 4:2:2 YCbCr 2048x1080P 47.95/48.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 2048-2 2048x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 4:4:4 X'Y'Z' 12-bit SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 2048-2 4:2:2 YCbCr 12-bit 2048x1080PsF 29.97/30.00 Hz...
  • Page 77 Transmission method Signal format Color format Color depth Standards 3G-SDI Level B x 1 1920x1080P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 1920x1080i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 274M 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 50.00 Hz 4:2:2 YCbCr 10-bit 1920x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit...
  • Page 78 Transmission method Signal format Color format Color depth Standards 3G-SDI Level B x 1 2048x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 2048x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit...
  • Page 79 Transmission method Signal format Color format Color depth Standards 3G-SDI Level B x 1 2048x1080PsF 23.98/24.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 HD-SDI x 4 3840x2160i 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 274M 3840x2160i 50.00 Hz 3840x2160P 29.97/30.00 Hz 3840x2160PsF 29.97/30.00 Hz 3840x2160P 25.00 Hz 3840x2160PsF 25.00 Hz 3840x2160P 23.98/24.00 Hz 3840x2160PsF 23.98/24.00 Hz 4096x2160i 59.94/60.00 Hz 4096x2160i 50.00 Hz 4096x2160P 29.97/30.00 Hz...
  • Page 80 Transmission method Signal format Color format Color depth Standards HD-SDI Dual x 4 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 372 SMPTE 274M 3840x2160i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 50.00 Hz 4:2:2 YCbCr 12-bit 3840x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 25.00 Hz...
  • Page 81 Transmission method Signal format Color format Color depth Standards HD-SDI Dual x 4 4096x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 372 SMPTE 2048-2 4:2:2 YCbCr 12-bit 4096x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 372 SMPTE 2048-2 4:2:2 YCbCr 12-bit 4096x2160P 25.00 Hz 4:4:4 RGB 12-bit/10-bit...
  • Page 82 Transmission method Signal format Color format Color depth Standards 3G-SDI Level A x 4 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 274M 3840x2160i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 50.00 Hz 4:2:2 YCbCr 12-bit 3840x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 29.97/30.00 Hz 4:4:4 RGB 10-bit 12-bit 4:4:4 YCbCr 12-bit 4:4:4 YCbCr...
  • Page 83 Transmission method Signal format Color format Color depth Standards 3G-SDI Level A x 4 4096x2160P 50.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 2048-2 4096x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:4:4 X'Y'Z' 12-bit 4:2:2 YCbCr 4096x2160P 47.95/48.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 2048-2 4096x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 2048-2 4:2:2 YCbCr 12-bit 4096x2160PsF 29.97/30.00 Hz...
  • Page 84 Transmission method Signal format Color format Color depth Standards 3G-SDI Level B x 4 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 3840x2160i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 274M 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 50.00 Hz 4:2:2 YCbCr 10-bit 3840x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit...
  • Page 85 Transmission method Signal format Color format Color depth Standards 3G-SDI Level B x 4 4096x2160P 47.95/48.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 372 SMPTE 2048-2 4096x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 4096x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2...
  • Page 86 ■ DisplayPort Horizontal frequency Signal format Standards PixelClock [MHz] Vertical frequency [Hz] [kHz] 640x480 VESA DMT 25.175 31.469 59.940 800x600 VESA DMT 40.000 37.879 60.317 1024x768 VESA DMT 65.000 48.363 60.004 1920x1080 VESA DMT 148.500 67.500 60.000 2048x1080 CVTRB VESA CVT 147.000 66.576 59.924 2048x1280 CVTRB VESA CVT 174.250 78.918 59.922...
  • Page 87: Image/Frame Display

    Image/Frame Display ■ SDI Input (Signal system) Output (Display frame rate) 1280x720 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 50.00 50.00 59.94/60.00 59.94/60.00 1920x1080 50.00 50.00 59.94/60.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 50.00 50.00 59.94/60.00 59.94/60.00...
  • Page 88 Input (Signal system) Output (Display frame rate) 4096x2160 50.00 50.00 59.94/60.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 47.95/48.00 47.95/48.00 50.00 50.00 59.94/60.00 59.94/60.00 * : Displaying same frame ■ DisplayPort Input (Signal system) Output (Display frame rate) 640x480 59.940 59.940...
  • Page 89: Error Messages

    Error Messages Message Description and Action Calibration Failed to initialize the external sensor. See CA-310 and CA-210 instruction manual. Calibration error. • Check the installation and connection of the external sensor and retry ( 31). • Perform matrix calibration of CA-310 and CA-210 32). Calibration is completed. Set the "Luminance" in calibration again ( 46). (Brightness setting is lower than target brightness.) Failed to detect the external sensor. Correctly connect the external sensor to the USB Please check the connection with the sensor. port of this main unit. Network Communication error. IP address may be in conflict or there may be a network communication error. Check the network environment. Invalid IP Address. Enter the correct IP address. Invalid Subnet Mask. Enter the correct subnet mask. Various settings, The USB memory is full. Use another USB memory or delete the content of CDL export the memory. Failed to write file. The USB memory may be defective or protected.
  • Page 90 Message Description and Action Hardware error Backlight error. Turn off the main power once and then back on. If the message persists, contact Canon Customer Fan error. Center. Panel error. I/F error. System error. Input signal No Signal Displayed when there is no video signal input. Unsupported Unsupported video signal is input. Check the supported signal format ( 72). "Input Configuration" is different from Payload. Check the "Input Configuration" ( 49) and "Signal Information" ( 68) settings. Reset any incorrect "Input Configuration" settings. Operation Invalid operation. Operation is disabled. Check the setting items. "Protect Settings" is on. To use the OSD menu, move the selection frame to "Protect Settings" and press the SET button for approximately 3 seconds. "CDL Bypass" is on. When "CDL Bypass" is turned "On", you cannot adjust the "Power", "Saturation", "Offset", or "Slope". Invalid Password. Enter the correct password. "Knob Lock" is on. If the knobs are not functioning, please set "Knob Lock" to "Off".
  • Page 91: Troubleshooting

    • Turn on the main power. (Power indicator does not turn on.) • Check that the AC power cord is connected correctly. • Brightness of the power indicator may be turned "Off". Turn it on and check once more. The screen is dark. When the power indicator does not turn on: • Turn on the main power. • Check that the AC power cord is connected correctly. When the power indicator is lit orange: • Press the button. When the power indicator is flashing orange: • Flashing once every 3 seconds : Contact Canon Customer Center. • Flashing twice every 3 seconds : T urn on the power with the button. If the power still does not turn on, contact Canon Customer Center. Main unit cannot be controlled with the • Check that the main unit and the display controller are connected display controller. correctly. • Pairing may not be performed correctly. Try re-pairing. • Check "Display List". When your display is not found in the list, the 64, 65 display controller does not recognize it. Check also network settings and your network state.
  • Page 92 Symptom Cause and Action "Aspect Marker", "Safety Zone Marker" or • A channel with no signal, unsupported signal, or with "Input "Area Marker" does not appear. Configuration" not set may be selected. Check the signal. • "H Delay" or "V Delay" is turned "On". Set to "Off". 59, 63, • Not displayed when "Peaking 1" or "Peaking 2" is selected. Set it to "Off". You forgot the password for "Protect • Press the F1 button and the button on the main unit while the video Settings". display is in standby. The configuration will be reset to the state where no password is set. The video display does not start up in the • Check the "Power on Setting" on the OSD menu. Set "Last memory" condition that the power was turned off to start up the video display in the condition that the power is turned off last time.
  • Page 93: Software Used In This Product

    Software Used in This Product Software installed with this product includes software modules from Canon or third parties. Software Developed by Canon and Free Software Software developed or created by Canon and accompanying document is protected by copyright law, terms of an international convention and any other governing laws. This product uses software modules under copyright by third parties and distributed as free software. Some of these software modules are subject to the GNU General Public License v2 (GPL), GNU Lesser General Public License v2.1 (LGPL) or any other license. Acquiring Source Code for Free Software Some free software requires the acquirement of the source code of modules in order to distribute the executable form of those software modules. For information on how to acquire the source code for free software such as these and confirming terms of the GPL, LGPL and other license agreements, please check with the distributor from whom the product was purchased. The following free software modules are installed to this product: • linux kernel • busybox • glibc • JFFS2 • SquashFS • FUSE • libfuse • libupnp • avahi-autoipd • libxml • zlib • libpng...
  • Page 94 ■libxml License Copyright (C) 1998-2003 Daniel Veillard. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE DANIEL VEILLARD BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Except as contained in this notice, the name of Daniel Veillard shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization from him. Software Used in This Product...
  • Page 95: Index

    Blue Only ..............63 Blue (Test Pattern) ............. 62 Brightness ............25, 40 False Color ..............59 Film Cadence ............53 Firmware Ver. ............. 68 Calibration ............31, 46 Format ............... 49 Canon Log, Canon Log 2 .......... 42 Frame Hold ............52, 59 CDL Bypass .............. 45 Function Guide ............63 CDL Export/Import ..........33, 45 Function Settings ............59 Center Marker ............58 Channel Name ............. 34, 49 Channel Settings ............
  • Page 96 H Delay ..............63 Password ..............65 HD-SDI ..............12, 17 Peaking ..............59 Hide OSD ..............67 Picture Mode ............. 40 PLUGE (Test Pattern) ..........62 Power ..............25, 45 Image Priority ............52 Power Indicator Brightness ........65 Input Configuration ............ 49 Power on Setting ............66 Internal Sync ............. 49 Protect Settings ............65 I/P Conversion .
  • Page 97 User 1-7 ..............40 User LUT ............. 41, 42 Various Function (Function Settings) ......63 V Delay ..............63 Vector Scope ............. 62 VITC ................60 Wave Form Monitor ........... 61 White (Test Pattern) ........... 62 YCbCr Color Matrix ........... 46 Zoom ................ 51 Index...
  • Page 98 Canon brand items is given by the manufacturer or producer thereof. If the Equipment contains a hard disk drive, Canon USA recommends that data stored on that drive be duplicated or backed up to prevent its loss in the event of failure or other malfunction of such drive.
  • Page 99 DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON USA AND CAUSING THE ALLEGED DAMAGE.
  • Page 100 Canon Canada, including any implied warranty or condition regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such non-Canon brand items is given by the manufacturer or producer thereof. If the Equipment contains a hard disk drive, Canon Canada recommends that data stored on that drive be duplicated or backed up to prevent its loss in the event of failure or other malfunction of such drive.
  • Page 101 THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF THE EQUIPMENT SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE.
  • Page 102 CANON MEXICANA, S DE RL DE CV http://www.canon.com.mx Canon Korea Consumer Imaging Inc. 52 (55) 5249-4900 http://www.canon-ci.co.kr 5F, Canon Bldg, 607, Teheran-ro, Gangnam-gu, Seoul, Korea +82(0)2-1588-8133 Visit your local Canon website to download the latest version of this instruction manual. MIE-0001-002 © CANON INC. 2015...

Table of Contents