Setting Lists In The Input Configuration Menu - Sony Trinitron BVM-20G1U Operation Manual

Setting Lists in the INPUT CONFIGURATION Menu

This section explains the setting lists displayed in the
menu.
How to read the setting lists
• For purposes of explanation, each setting list is
preceded by a menu number. These numbers are not
displayed on the screen.
For more information about the menu number, see "About
menu numbers" on page 19.
• The arrow mark (÷) refers you to another setting list
that appears after you make the setting, or to an
operation that is carried out as a result of the setting.
When there is no arrow mark, the menu does not have
any sub-list.
[C1] INPUT CONFIGURATION menu (1/2)
Set input signal data for each channel.
xxCH: Current channel is indicated. To change the
channel, enter a channel number with the numeric
keypad. The settings below will be stored as
information about the signal to be connected to this
channel.
FORMAT: Select the input signal type. ÷[C11]
SLOT NO: Enter the slot number.
INPUT NO: Enter the input connector number.
YC SEP: Select Y/C separation filter. ÷[C12]
SYNC MODE: Select the sync signal.
INT: Use an internal sync signal.
EXT: Use an external sync signal.
SCREEN MODE: Select the scan size. ÷[C13]
SAFE AREA: Choose whether or not to display the
safe area (OFF or ON).
SAFE AREA SCALE: Select the modes for safe area.
÷[C14]
APERTURE: Choose whether to use aperture
adjustment or not (OFF or ON).
APERTURE VALUE: Enter the aperture adjustment
value (0 to 200).
[C1] INPUT CONFIGURATION menu (2/2)
Set input signal data for each channel.
xxCH: Current channel is indicated. To change the
channel, enter a channel number with the numeric
keypad. The settings below will be stored as
information about the signal to be connected to this
channel.
FILTER: Switch the filter operation (OFF or ON)
when the monochrome display is selected.
CHANNEL NAME: Give the channel a name.
÷ [C15]
COLOR TEMP: Set the color temperature. Select
STD, COL1 or COL2.
STD: Use common data (factory setting: D65).
COL1: Use common data (factory setting: D93).
COL2: Use common data (factory setting: D56/
1)
D65 ).
H PHASE: Set the horizontal picture position (–128 to
+127).
SAD H POSITION: Adjust the horizontal display
position of the safety area (–128 to +127).
COPY: Select a method for copying data from
elsewhere. ÷[C16]
Note
For H PHASE and SAD H POSITION data, if values
above or below the allowable range are entered, the
monitor will not operate correctly.
[C11] FORMAT menu (xxCH)
Select the signal format.
COMPOSITE: Composite signal ÷ [C111]
YC: Y/C signal ÷ [C112]
COMPONENT: Component or RGB signal
÷ [C113]
SDI: Serial digital signal ÷ [C114]
Note
If there is no input connector or decoder corresponding
to a format, that format will not be selectable (the
cursor will skip over that item).
[C12] YC SEP menu
Select a Y/C separation filter.
TRAP/BPF: Select TRAP/BPF filter.
2 LINES COMB: Select 2 LINES COMB filter.
3 LINES COMB: Select 3 LINES COMB filter.
[C13] SCREEN MODE menu (xxCH)
Select the scan size.
4:3-NORM: Overscanned 4:3 aspect ratio. (when not
using 16:9 mask)
4:3-UNDR: Underscanned 4:3 aspect ratio. (when not
using 16:9 mask)
16:9-NORM: Overscanned 16:9 aspect ratio.
16:9-UNDR: Underscanned 16:9 aspect ratio.
[C14] SAFE AREA SCALE
Select the setting for each items of SAFE AREA
setting list.
80: Displays a 80% safe area in 4:3 screen.
90: Displays a 90% safe area in 4:3 screen.
100: Displays an 100% safe area in 4:3 screen.
16:9-80: Displays a 80% of 16:9 aspect ratio safe area
in 4:3 screen.
......................................................................................
1) D56: BVM-20G1U/14G1U/14G5U
D65: BVM-20G1E/20G1A/14G1E/14G1A/14G5E/
14G5A
33