Parts List; Return To Cembre For Overhaul - Cembre B-TC04 Operation And Maintenance Manual

ENGLISH
4.3) Oil top up
If necessary, top up the oil as follows:
Remove the battery, place the tool in a vertical posi-
tion, remove the cap (24) located inside the battery
housing, fill the reservoir to the top then replace
the cap.
Always use clean recommended oil, see § 1.
Do not use old or recycled oil.
Do not use hydraulic brake fluid.
4.4) Blade replacement
(Ref. to Figs. 4 and 5)
After extended use, the blades may lose their cutting edge.
Replace the blades as follows:
4.4.1) Lower blade: (Ref. to Fig. 5)
– Remove locking pin (04) and open tool head.
– Operate the tool to advance the lower blade (14) until spring pins (16 and 41) are visible
on the ram (06).
– Remove spring pins (16 and 41) using a drift and remove the lower blade.
– Insert the new blade and secure with spring pins.
Warning: before closing the tool head release the oil pressure and retract the lower
blade, otherwise the head may hit the lower blade edge and damage it.
4.4.2) Upper blade: (Ref. to Fig. 4)
– With the lower blade (14) fully retracted, the tool head closed and the locking pin (04) fully
secured, hold the tool on the blade spacer (08) or (13) in a bench vice (see fig. 4).
– By an 8 mm wrench, unscrew 4-set pins (03),remove the two holding plates (02) and the
upper blade (09) noting the position of the cutting edge bevel.
– Insert the new blade, noting the position of the cutting edge bevel.
– Fit the 2 holding plates (02) and secure with 4-set pins (03).

5. RETURN TO Cembre FOR OVERHAUL

In the case of a breakdown contact our Area Agent who will advise you on the problem
and give you the necessary instructions on how to dispatch the tool to our nearest service
Centre; if possible, attach a copy of the Test Certificate supplied by Cembre together with
the tool or, if no other references are available, indicate the approximate purchase date and
the tool serial number.
24
8

6. PARTS LIST

(Refer to Fig. 6)
Code N° Item DESCRIPTION
6580060 ▲ 02 HOLDING PLATE
6900380 ▲ 03 M 10X35 scrEw
6560740 04 LOcKING PIN
6170080 05 cHAiN
6620140 06 rAM
6760340 07 ø 5x40 sPrING PIN
6220020 ▲ 08 rIGHT BLADE sPAcEr
6420160 ▲ 09 UPPEr BLADE
6000354 10 wrIsTsTrAP
6780020 ▲ 11 BLADE sUPPOrT
6220040 ▲ 13 LEFT BLADE sPAcEr
6420140 14 LOwEr BLADE
6040427 15 sTrAP ANcHOr rING
6760240 16 ø 4x20 sPrING PIN
6000383 17 PrEssUrE rELEAsE BUTTON
6000236 18 OPErATING PUsH-BUTTON
6040427 19 sTrAP ANcHOr rING
– 20 14.4V - 3.0Ah - BATTErY
The guarantee is void if parts used are not Cembre original spares.
When ordering spare parts always specify the following:
- code number of item
- name of item
- type of tool
- tool serial number
______________________
Acoustic noise (Directive 2006/42/EC, annexe 1, point 1.7.4.2 letter u)
– The weighted continuous acoustic pressure level equivalent
A at the work place L is equal to .....................................................................72,4 dB (A)
pA
– The maximum value of the weighted acoustic displacement
pressure C at the work place L is ........................................................... < 130 dB (C)
pCPeak
– The acoustic power level emitted by the machine
L is equal to ....................................................................................................83,1 dB (A)
WA
Risks due to vibration (Directive 2006/42/EC, annexe 1, point 2.2.1.1)
Tests carried out in compliance with the indications contained in UNI ENV 25349 and UNI
EN 28662 part 1 Standards, and under operating conditions much more severe than those
st
normally found, certify that the weighted root mean square in frequency of the accele-
ration the upper limbs are exposed to for each biodynamic reference axis does not
exceed 2.5 m/sec .
2
9
ENGLISH
Qty Code N° Item DESCRIPTION
2 6080100 ▲ 22 BUsH
4 6800040 24 rEsErVOIr cAP
1 6000411 25 sOcKET cAP
1 – 26 sOcKET
1 6720075 29 rEsErVOIr
1 6080100 ▲ 30 BUsH
6740020 31 1/4" BALL
1
1 6520570 32 sPrING
1 6000310 33 MOTOr
1 6232243 34 (TG. 0443) LABEL
1 – 35 TOOL LABEL
1 6232038 37 (TG. 0352) wArNING LABEL
1 6650140 38 D.8,4 wAsHEr
1 6180300 39 M 8 NUT
1 6560400 40 HEAD LOcKING PIN
1 6760011 41 ø 2,5x20 sPrING PIN
1 6040425 42 rING
1 6860110 cOMPLETE HEAD
▲
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2