Table of Contents
Advertisement
6
automatically adjusts for summer/winter time changes. It is
+ or - and > to accept change.
activated automatically on 1st installation. There should be no
22:30
need to change these settings, however, should you wish to, it
To select option 06 press > until option 06 display is shown
10.0
can be done in Option 05.
(fig 11)
(Option 05)
How to adjust date and time.
Enter user options, select option 05 (fig 6)
User Guide
To change the year press > once (fig 7)
To change the month press > again (fig 8)
To change the day press > again (fig 9)
How to replace the batteries see fig 3.
To change the time press > again (fig 10)
Once you have selected your required display, to adjust press
Remove the battery cover using a coin. Replace the spent
6
(Fig 6)
+ or - and > to accept change.
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
22:30
correct orientation. Replace the battery cover pressing fully home.
To select option 06 press > until option 06 display is shown
10.0
(fig 11)
Fig 5
(Fig 8)
(Fig 3)
(Fig 7)
(Fig 6)
indicator will
(Fig 10)
Fig 6
(Fig 9)
6
(Fig 8)
22:30
(Fig 7)
16.0
1
2
Basic Settings
6:30
8:30
12:00
20.0
16.0
16.0
The Digistat +2RF thermostat is a programmable thermostat
*The above settings can be understood using the chart below
24-Hour (the same program for every day of the week) and
(Fig 11)
allows you to set 6 time and temperature events per day.
(Fig 10)
Fig 7
25ºC
Digistat +2RF
(Fig 9)
20ºC
Pre-set Program
6
Drayton
(Option 06)
Your Digistat +2RF comes with the following default settings
(Fig 3)
22:30
15ºC
How to change temperature offset.
pre-programmed for your convenience:
16.0
The temperature displayed on the thermostat may not match
10ºC
that of other temperature measuring devices in the controlled
Pre-set Program 1. (9 til 5)
press
to confirm and
(Fig 3)
space, because of its location. The displayed temperature may
use the + or – button to
Event
5ºC
be offset to bring it in line with other devices. To adjust the
adjust required temperature
Time
1
2
3
temperature, enter the user options, select option 06. The
(temperature shown flashing)
Temperature
temperature may be offset by +/- 5 degrees by pressing the
06:30 08:30 12:00 14:00 16:30 22:30
Fig 8
(Fig 11)
+ and – keys. Press > to accept the desired change.
*The above settings can be understood using the chart below
Time Period
(Option 07)
25ºC
How to restore the built in time temperature programs.
Option 06 - How to change temperature
Enter user options, select option 07 and use + and – keys to
(Option 06)
20ºC
offset
select desired option. Off = current programs retained. On =
How to change temperature offset.
been set press
to
restore factory program settings. Press > to select the desired
The temperature displayed on the thermostat may not match
15ºC
confirm and move to the next
The temperature displayed on the thermostat may not
change. The Option 07 display automatically reverts back to
that of other temperature measuring devices in the controlled
time and temperature periods
OFF. Please note enabling this function will lose any user
match that of other temperature measuring devices in
1
2
space, because of its location. The displayed temperature may
10ºC
to be adjusted confirming
changes to the preset programs.
the controlled space, because of its location. The
be offset to bring it in line with other devices. To adjust the
6:30
8:30
12:00
changes by pressing
temperature, enter the user options, select option 06. The
displayed temperature may be offset to bring it in line
20.0
16.0
16.0
5ºC
button. (max 6 periods).
temperature may be offset by +/- 5 degrees by pressing the
with other devices. To adjust the temperature, enter the
(Option 08)
1
2
*The above settings can be understood using the chart below
+ and – keys. Press > to accept the desired change.
user options, select option 06. The temperature may be
How to disable the OFF function.
6:30
8:30
12:00
To disable the OFF function, enter user options, select option
offset by +/- 5 degrees by pressing the + and – keys.
20.0
16.0
16.0
25ºC
(Option 07)
08 and use + or – keys to select Off. Press > to accept change.
Press
or
*The above settings can be understood using the chart below
It is now not possible to switch the Digistat+2RF OFF using the
How to restore the built in time temperature programs.
until you return to auto
+ and- keys as previously described. To enable the OFF
20ºC
Enter user options, select option 07 and use + and – keys to
mode with the bottom arrow
function return to option 08 and select ON. Press > to accept
select desired option. Off = current programs retained. On =
25ºC
pointing to auto (as shown).
change.
15ºC
As you can see, at 06:30 , the heating will come on to raise the
restore factory program settings. Press > to select the desired
twice until the
temperature to 20ºC. At 08:30, the temperature set point is
change. The Option 07 display automatically reverts back to
20ºC
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
10ºC
OFF. Please note enabling this function will lose any user
day, until 16:30 when the temperature increases to 21ºC. The
changes to the preset programs.
15ºC
temperature then drops down to a night-setback temperature of
5ºC
Congratulations!
1
7ºC until 06:30 when the cycle repeats for the next day.
2
3
18
10ºC
(Option 08)
The unit is now set correctly to follow your required timings.
06:30 08:30 12:00 14:00 16:30 22:30
How to disable the OFF function.
5ºC
Time Period
To disable the OFF function, enter user options, select option
1
2
3
08 and use + or – keys to select Off. Press > to accept change.
It is now not possible to switch the Digistat+2RF OFF using the
To adjust these times and temperatures
06:30 08:30 12:00 14:00 16:30 22:30
+ and- keys as previously described. To enable the OFF
Time Period
function return to option 08 and select ON. Press > to accept
change.
1. With the product operating as
normal in the Auto mode
adjust set temperature. Set
press
twice until the
temperature shown flashing
display is flashing as shown.
(Fig 2)
The default is OFF mode allowing you to adjust the Digistat +2RF.
feature is enabled by the installer.
To Lock the Digistat +2RF settings enter the User Options Menu
Option 09 and select On and press > to accept.
When the delay period is operating indicated by the flame symbol
Once the User Options Menu is exited all buttons will be locked.
flashing (Fig12), pressing any button returns the Digistat +2RF to
To switch off the Protection Lock enter the User Menu and change
auto mode allowing normal button operation until the next time/
How to replace the batteries see fig 3.
to OFF. Press > to accept.
temperature event, when it will resume the delay start mode or
Once the User Menu is exited all buttons will be free to adjust.
follows the Holiday, Manual, Override or Off modes as selected.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
Changes to the installer options and pre-set programmes must be
correct orientation. Replace the battery cover pressing fully home.
made with the flame symbol not flashing.
Special Note:
The following only applies when the Intelligent delayed start
feature is enabled by the installer.
When the delay period is operating indicated by the flame symbol
flashing (Fig12), pressing any button returns the Digistat +2RF to
auto mode allowing normal button operation until the next time/
temperature event, when it will resume the delay start mode or
follows the Holiday, Manual, Override or Off modes as selected.
Changes to the installer options and pre-set programmes must be
made with the flame symbol not flashing.
What is Intelligent delayed start?
Intelligent Delayed Start (Energy saving feature)
The Intelligent Delayed Start is an energy saving feature which
automatically reduces the warm up time for the heating system. As
the weather becomes milder, Intelligent Start will delay the heating
start times so that the fuel is not wasted bringing the room up to
temperature earlier than necessary.
Basic Settings
(Fig 3)
The Digistat +2RF thermostat is a programmable thermostat
What is Intelligent delayed start?
24-Hour (the same program for every day of the week) and
3
4
5
6
allows you to set 6 time and temperature events per day.
14:00
16:30
22:30
Intelligent Delayed Start (Energy saving feature)
16.0
21.0
7.0
Digistat +2RF
The Intelligent Delayed Start is an energy saving feature which
Pre-set Program
automatically reduces the warm up time for the heating system. As
the weather becomes milder, Intelligent Start will delay the heating
Your Digistat +2RF comes with the following default settings
pre-programmed for your convenience:
start times so that the fuel is not wasted bringing the room up to
temperature earlier than necessary.
Pre-set Program 1. (9 til 5)
Event
Time
6:30
Temperature
20.0
*The above settings can be understood using the chart below
1
2
3
4
6:30
8:30
12:00
14:00
4
5
6
25ºC
20.0
16.0
16.0
16.0
20ºC
(* small 1 in lower half of screen
shows which time period is being set
15ºC
e.g. 1=1st period, 2 = 2nd period etc)
10ºC
5ºC
1
3
4
5
6
06:30 08:30 12:00 14:00 16:30 22:30
14:00
16:30
22:30
16.0
21.0
7.0
1
2
3
4
5
3
4
5
6
14:00
16:30
22:30
06:30 08:30 12:00 14:00 16:30 22:30
16.0
21.0
7.0
Time Period
As you can see, at 06:30 , the heating will come on to raise the
to accept the desired change.
temperature to 20ºC. At 08:30, the temperature set point is
dropped from 20ºC down to16ºC, it stays at 16ºC throughout the
day, until 16:30 when the temperature increases to 21ºC. The
temperature then drops down to a night-setback temperature of
7ºC until 06:30 when the cycle repeats for the next day.
4
5
6
To adjust these times and temperatures
4
5
6
1. With the product operating as
normal in the Auto mode
press
twice until the
display is flashing as shown.
The time will be flashing, use
the + or - buttons to adjust
the 1st time as required
use the + or – button to
adjust required temperature
(temperature shown flashing)
3. Once the temperature has
been set press
to
confirm and move to the next
Option 07 - How to restore the built in time
time and temperature periods
2. Once the time has been set
to be adjusted confirming
press
temperature programs
changes by pressing
use the + or – button to
button. (max 6 periods).
adjust required temperature
Enter user options, select option 07 and use + and –
(temperature shown flashing)
keys to select desired option. Off = current programs
retained. On = restore factory program settings.
Press
4. To exit press
or
display automatically reverts back to OFF. Please note
until you return to auto
mode with the bottom arrow
enabling this function will lose any user changes to the
(Fig 12)
pointing to auto (as shown).
preset programs.
(Fig 8)
3. Once the temperature has
been set press
2. Once the time has been set
confirm and move to the next
Option 08 - How to disable the OFF function
press
to confirm and
time and temperature periods
use the + or – button to
Congratulations!
to be adjusted confirming
adjust required temperature
To disable the OFF function, enter user options, select
2. Once the time has been set
changes by pressing
(temperature shown flashing)
The unit is now set correctly to follow your required timings.
option 08 and use + or – keys to select Off. Press
press
to confirm and
button. (max 6 periods).
to accept change. It is now not possible to switch the
use the + or – button to
Digistat+2RF OFF using the + and- keys as previously
adjust required temperature
(Fig 3)
To change temperature for a short period (Override):
(temperature shown flashing)
described. To enable the OFF function return to option
(Fig 10)
08 and select ON. Press
4. To exit press
until you return to auto
(Fig 12)
mode with the bottom arrow
3. Once the temperature has
(Fig 8)
1. Press + or - buttons to
Option 09 - How to lock the key pad - Access
pointing to auto (as shown).
been set press
to
adjust set temperature. Set
confirm and move to the next
Protection Lock
temperature shown flashing
time and temperature periods
3. Once the temperature has
to be adjusted confirming
been set press
The access protection lock allows you to lock the
to
changes by pressing
confirm and move to the next
Digistat +2RF so that it cannot have any adjustments.
button. (max 6 periods).
time and temperature periods
The default is OFF mode allowing you to adjust the
2. After 5 seconds will start
to be adjusted confirming
The unit is now set correctly to follow your required timings.
Digistat +2RF. To Lock the Digistat +2RF settings enter
controlling at selected set
changes by pressing
the User Options Menu Option 09 and select On and
point but displays actual room
button. (max 6 periods).
(Fig 10)
press
4. To exit press
or
temperature. 2 chrevons
To change temperature for a short period (Override):
until you return to auto
is exited all buttons will be locked. To switch off the
indicates override mode.
1
2
3
4
mode with the bottom arrow
Protection Lock enter the User Menu and change to OFF.
pointing to auto (as shown).
8:30
12:00
14:00
Press
4. To exit press
or
16.0
16.0
16.0
until you return to auto
buttons will be free to adjust.
1. Press + or - buttons to
mode with the bottom arrow
3. To exit override press
adjust set temperature. Set
pointing to auto (as shown).
5
6
once or wait until next change
temperature shown flashing
16:30
22:30
in the pre-set program.
Congratulations!
SPECIAL NOTE:
21.0
7.0
The following only applies when the Intelligent
The unit is now set correctly to follow your required timings.
delayed start feature is enabled by the installer.
Congratulations!
2. After 5 seconds will start
controlling at selected set
To change temperature for a short period (Override):
The unit is now set correctly to follow your required timings.
point but displays actual room
When the delay period is operating indicated by the
temperature. 2 chrevons
To set a constant room temperature (Manual mode):
flame symbol flashing (Fig 9), pressing any button
indicates override mode.
returns the Digistat +2RF to auto mode allowing normal
To change temperature for a short period (Override):
button operation until the next time/ temperature event,
1. Press + or - buttons to
2
3
4
5
when it will resume the delay start mode or follows the
adjust set temperature. Set
1. Press
once, the display
temperature shown flashing
Holiday, Manual, Override or Off modes as selected.
shows temperature flashing
3. To exit override press
Time Period
1. Press + or - buttons to
(example 20
C)
0
Changes to the installer options and pre-set programmes
once or wait until next change
adjust set temperature. Set
6
in the pre-set program.
must be made with the flame symbol not flashing.
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
2. Press + or - buttons to
point but displays actual room
adjust the temperature as
temperature. 2 chrevons
required. The temperature
2. After 5 seconds will start
indicates override mode.
will stop flashing after 5
controlling at selected set
seconds and start controlling
To set a constant room temperature (Manual mode):
point but displays actual room
at this temperature
temperature. 2 chrevons
indicates override mode.
3. To exit override press
1. Press
once or wait until next change
3. To exit manual mode press
shows temperature flashing
in the pre-set program.
(example 20
once, to return to auto.
3. To exit override press
once or wait until next change
in the pre-set program.
2. Press + or - buttons to
adjust the temperature as
To set a constant room temperature (Manual mode):
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
The access protection lock allows you to lock the Digistat +2RF so
that it cannot have any adjustments.
The following only applies when the Intelligent delayed start
The default is OFF mode allowing you to adjust the Digistat +2RF.
feature is enabled by the installer.
To Lock the Digistat +2RF settings enter the User Options Menu
Option 09 and select On and press > to accept.
When the delay period is operating indicated by the flame symbol
(* small 1 in lower half of screen
Once the User Options Menu is exited all buttons will be locked.
shows which time period is being set
flashing (Fig12), pressing any button returns the Digistat +2RF to
To switch off the Protection Lock enter the User Menu and change
e.g. 1=1st period, 2 = 2nd period etc)
auto mode allowing normal button operation until the next time/
DIGISTAT+2RF Room Thermostat
to OFF. Press > to accept.
2. Once the time has been set
temperature event, when it will resume the delay start mode or
Once the User Menu is exited all buttons will be free to adjust.
press
follows the Holiday, Manual, Override or Off modes as selected.
use the + or – button to
adjust required temperature
Changes to the installer options and pre-set programmes must be
(temperature shown flashing)
Special Note:
made with the flame symbol not flashing.
to confirm and
The following only applies when the Intelligent delayed start
feature is enabled by the installer.
When the delay period is operating indicated by the flame symbol
3. Once the temperature has
to select the desired change. The Option 07
flashing (Fig12), pressing any button returns the Digistat +2RF to
been set press
auto mode allowing normal button operation until the next time/
shows which time period is being set
confirm and move to the next
e.g. 1=1st period, 2 = 2nd period etc)
temperature event, when it will resume the delay start mode or
time and temperature periods
follows the Holiday, Manual, Override or Off modes as selected.
to be adjusted confirming
changes by pressing
Changes to the installer options and pre-set programmes must be
to
button. (max 6 periods).
made with the flame symbol not flashing.
What is Intelligent delayed start?
Intelligent Delayed Start (Energy saving feature)
4. To exit press
The Intelligent Delayed Start is an energy saving feature which
until you return to auto
automatically reduces the warm up time for the heating system. As
mode with the bottom arrow
(* small 1 in lower half of screen
the weather becomes milder, Intelligent Start will delay the heating
pointing to auto (as shown).
shows which time period is being set
start times so that the fuel is not wasted bringing the room up to
to accept change.
e.g. 1=1st period, 2 = 2nd period etc)
or
temperature earlier than necessary.
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
The unit is now set correctly to follow your required timin
What is Intelligent delayed start?
Intelligent Delayed Start (Energy saving feature)
Congratulations!
To change temperature for a short period (Overr
The Intelligent Delayed Start is an energy saving feature which
automatically reduces the warm up time for the heating system. As
the weather becomes milder, Intelligent Start will delay the heating
to accept. Once the User Options Menu
start times so that the fuel is not wasted bringing the room up to
1. Press + or - buttons to
temperature earlier than necessary.
adjust set temperature. Set
5
6
temperature shown flashing
16:30
22:30
to accept. Once the User Menu is exited all
21.0
7.0
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
6
in the pre-set program.
To set a constant room temperature (Manual mod
1. Press
shows temperature flashing
(example 20
once, the display
Installation & User Guide
2. Press + or - buttons to
C)
0
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
to confirm and
(* small 1 in lower half of s
shows which time period is be
e.g. 1=1st period, 2 = 2nd per
(* small 1 in lower half of screen
to
(Fig 12)
or
(Fig 12)
Congratulations!
once, the display
C)
0
once, to return to auto.
Hide quick links:
Advertisement
Table of Contents
