Table of Contents
Advertisement
Installation Guide
2. Once the time has been set
Installer Options
press
to confirm and
use the + or – button to
adjust required temperature
If you wish to change any of the Installer Options as
2. Once the time has been set
(temperature shown flashing)
2. Once the time has been set
shown in the table below, enter the Installer Option
press
press
to confirm and
to confirm and
Menu from Auto mode by pressing:
use the + or – button to
use the + or – button to
simultaneously for 5 seconds.
adjust required temperature
adjust required temperature
(temperature shown flashing)
(temperature shown flashing)
3. Once the temperature has
been set press
confirm and move to the next
time and temperature periods
3. Once the temperature has
to be adjusted confirming
3. Once the temperature has
been set press
been set press
changes by pressing
to
confirm and move to the next
button. (max 6 periods).
confirm and move to the next
time and temperature periods
time and temperature periods
to be adjusted confirming
to be adjusted confirming
changes by pressing
changes by pressing
How to replace the batteries see fig 3.
Pressing
4. To exit press
button. (max 6 periods).
button. (max 6 periods).
Menu and return to Auto mode.
until you return to auto
Remove the battery cover using a coin. Replace the spent
mode with the bottom arrow
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
Once the Installer Options screen has been selected,
pointing to auto (as shown).
correct orientation. Replace the battery cover pressing fully home.
3
4
5
6
the
4. To exit press
and
4. To exit press
or
12:00
14:00
16:30
22:30
until you return to auto
until you return to auto
through the Menu (shown below). The + and - allow you
16.0
16.0
21.0
7.0
mode with the bottom arrow
mode with the bottom arrow
to change values.
pointing to auto (as shown).
pointing to auto (as shown).
Once a value has been changed pressing
exiting the Menu will save the new setting. (The below
The unit is now set correctly to follow your required timings.
display shows Option 02 OFF).
Congratulations!
Congratulations!
To change temperature for a short period (Override):
The unit is now set correctly to follow your required timings.
The unit is now set correctly to follow your required timings.
To change temperature for a short period (Override):
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
6
4
5
6
temperature shown flashing
1. Press + or - buttons to
1. Press + or - buttons to
adjust set temperature. Set
adjust set temperature. Set
temperature shown flashing
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
3
4
5
6
indicates override mode.
2. After 5 seconds will start
2. After 5 seconds will start
Basic Settings
14:00
16:30
22:30
controlling at selected set
controlling at selected set
16.0
21.0
7.0
point but displays actual room
point but displays actual room
The Digistat +2RF thermostat is a programmable thermostat
temperature. 2 chrevons
temperature. 2 chrevons
24-Hour (the same program for every day of the week) and
indicates override mode.
indicates override mode.
allows you to set 6 time and temperature events per day.
3. To exit override press
once or wait until next change
in the pre-set program.
Digistat +2RF
Pre-set Program
3. To exit override press
3. To exit override press
Your Digistat +2RF comes with the following default settings
once or wait until next change
once or wait until next change
pre-programmed for your convenience:
in the pre-set program.
in the pre-set program.
Pre-set Program 1. (9 til 5)
To set a constant room temperature (Manual mode):
Event
4
5
6
Time
Temperature
To set a constant room temperature (Manual mode):
1. Press
once, the display
To set a constant room temperature (Manual mode):
shows temperature flashing
8
(example 20
C)
0
25ºC
1. Press
once, the display
1. Press
once, the display
20ºC
shows temperature flashing
shows temperature flashing
(example 20
(example 20
C)
C)
0
0
2. Press + or - buttons to
15ºC
adjust the temperature as
required. The temperature
10ºC
will stop flashing after 5
seconds and start controlling
2. Press + or - buttons to
2. Press + or - buttons to
5ºC
at this temperature
adjust the temperature as
adjust the temperature as
required. The temperature
required. The temperature
will stop flashing after 5
will stop flashing after 5
(temperature shown flashing)
3. Once the temperature has
been set press
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
4. To exit press
until you return to auto
(* small 1 in lower half of screen
mode with the bottom arrow
shows which time period is being set
2. Once the time has been set
e.g. 1=1st period, 2 = 2nd period etc)
pointing to auto (as shown).
press
to confirm and
use the + or – button to
(* small 1 in lower half of screen
(* small 1 in lower half of screen
adjust required temperature
to
shows which time period is being set
shows which time period is being set
(temperature shown flashing)
e.g. 1=1st period, 2 = 2nd period etc)
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
to
To change temperature for a short period (Override):
3. Once the temperature has
been set press
and + again for 5 seconds will exit the
or
confirm and move to the next
time and temperature periods
1. Press + or - buttons to
to be adjusted confirming
adjust set temperature. Set
changes by pressing
or
buttons allow you to scroll
temperature shown flashing
button. (max 6 periods).
Congratulations!
4. To exit press
or
2. After 5 seconds will start
until you return to auto
controlling at selected set
mode with the bottom arrow
point but displays actual room
pointing to auto (as shown).
temperature. 2 chrevons
indicates override mode.
Congratulations!
3. To exit override press
The unit is now set correctly to follow your required timings.
once or wait until next change
in the pre-set program.
To change temperature for a short period (Override):
(Fig 3)
1. Press + or - buttons to
To set a constant room temperature (Manual mode):
adjust set temperature. Set
temperature shown flashing
1. Press
once, the display
shows temperature flashing
2. After 5 seconds will start
(example 20
C)
0
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
3. To exit override press
at this temperature
1
2
3
once or wait until next change
6:30
8:30
12:00
14:00
in the pre-set program.
20.0
16.0
16.0
16.0
*The above settings can be understood using the chart below
3. To exit manual mode press
once, to return to auto.
To set a constant room temperature (Manual mode):
1. Press
once, the display
shows temperature flashing
(example 20
C)
0
1
2
3
4
5
06:30 08:30 12:00 14:00 16:30 22:30
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
to
Installer
Options
02
and +
or
04
05
06
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
10
to
11
2. Once the time has been set
12
13
before
Option 02 - Freeze Protection
3. Once the temperature has
Freeze protection will switch on the heating if the room
temperature falls to 5°C and will then control the
temperature at 7°C even if the Digistat is in OFF mode.
The Freeze Protection default is ON.
To switch off the Freeze Protection mode enter the
Installer Options Menu (Refer to Installer Options 02)
and change to OFF. Press
4. To exit press
Option 04 & 05 - Low and High Limit
set points.
The user temperature set points defaults are High 32°C
and Low 5°C, to change these limits enter the Installer
Options Menu (Refer to Installer Options 04 & 05).
The unit is now set correctly to follow your required timings.
Option 06 - Intelligent Delayed Start
(Energy saving feature).
To change temperature for a short period (Override):
The Intelligent Delayed Start is an energy saving feature
which automatically reduces the warm up time for the
heating system.
1. Press + or - buttons to
4
5
6
16:30
22:30
21.0
7.0
2. After 5 seconds will start
3. To exit override press
6
Function
Select
Option
Freeze
On
protection
Low Set
5
Point °C
High Set
Low
Point °C
Limit
Delayed
On
Start
(Energy
saving
feature)
Valve
On
protection
Valve
1
protection
press
to confirm and
time (Mins)
use the + or – button to
adjust required temperature
Application
0
(temperature shown flashing)
type
System
0
Capability
been set press
to
confirm and move to the next
time and temperature periods
to be adjusted confirming
changes by pressing
button. (max 6 periods).
to accept.
or
until you return to auto
mode with the bottom arrow
pointing to auto (as shown).
Congratulations!
adjust set temperature. Set
temperature shown flashing
Installation & User Guide
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
once or wait until next change
in the pre-set program.
DIGISTAT+2RF
Default
Off
On
High
5
Limit
32
32
Off
Off
Off
Off
5
3
1
0
1
0
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Hide quick links:
Advertisement
Table of Contents
