3. GX-20 : Fig. 3 …………………………………………………………………………………… 38 4. GX-20 : Fig. 4 …………………………………………………………………………………… 39 PARTS LIST FOR GX-20_CODE ……………………………………………………………… 40 5. PACKING ITEM_GX-20 ………………………………………………………………………… 38 . WIRING DIAGRAM ✄ ………………………………………………………………………………………………… 54 - This Document can not be used without Samsung's authorization -...
Page 3
18. Photometric element position adjustment procedure ……………………………………… 147 . SERVICE INFORMATION ✂ 1. Caution ………………………………………………………………………………………… 149 2. Disassembling Process For Camera Body ………………………………………………… 150 3. Assembling Process For Camera Body ……………………………………………………… 178 - This Document can not be used without Samsung's authorization -...
- Modes : Auto, Program, Shutter Priority AE, Aperture Priority AE, Sensitivity Priority AE, Shutter & Aperture Priority, Manual, Bulb, Flash X-sync, User Mode - Compensation : ±3 EV (1/2 EV step), ±2EV (1/3 EV step) - AE Lock : AEL - This Document can not be used without Samsung's authorization -...
Page 5
2.3fps (Standard Continuous : up to 16 shots) Shake Reduction - Type : Image Sensor Shift - Effective Range : Max. 4EV (depends on lens and shooting conditions) Dust Reduction - Yes - This Document can not be used without Samsung's authorization -...
Page 6
•6M : Super Fine (1)91, Super Fine (2)147, Fine 254, Normal 474 •2M : Super Fine (1)239, Super Fine (2)381, Fine 639, Normal 1060 ✁ T hese fi gures are measured under Samsung's standard conditions and may vary depending on shooting conditions and camera settings. Image Play...
Page 7
- 727g (Body only) , 806g (Memory card & Battery included) Operating Temperature - 0 ~ 40°C Operating Humidity - 5 ~ 85% Software - Application : Samsung Master, Samsung RAW Converter 2.0, Adobe Reader - This Document can not be used without Samsung's authorization -...
1024x768 pixels, 16-bit color display compatible monitor (24-bit color display recommended) Power Mac G4 or later Mac OS 10.2 or later Minimum 256MB RAM For Macintosh 250MB of available hard-disk space USB port CD-ROM drive - This Document can not be used without Samsung's authorization -...
Do not attempt to adjust the ✁ aperture lever or the mirror DC input terminal in the camera body. Failure to follow this instruction may cause the product to malfunction. - This Document can not be used without Samsung's authorization -...
Page 10
Picture Wizard OK Button INFO button Direction button Playback button Card access lamp Card cover lock LCD Monitor OIS (Optical Image Stabilization) lever Focus point selection dial Fn Button - This Document can not be used without Samsung's authorization -...
B attery grip supports the green button ( ) function ✁ while you can still adjust the exposure using the battery grip. Vertical position when using the ✂ battery grip - This Document can not be used without Samsung's authorization -...
2. Insert the battery as shown on the picture. Battery lock lever 3. Close the Battery cover and rotate the battery cover lock lever as shown. - This Document can not be used without Samsung's authorization -...
If the memory card cover is left open, the power will ✆ not turn on. Make sure the memory card is correctly positioned ✆ Lock button before inserting it into the camera. - This Document can not be used without Samsung's authorization -...
After attaching, check that the lens is secure. Also check that the red dots of the lens are on top and the attached portion does not move sideways. - This Document can not be used without Samsung's authorization -...
Page 15
Attaching and removing the lens must be done in a clean place. Please avoid contact with liquid water. If the camera°Øs body or the lens gets wet or dirty, camera malfunction may occur. - This Document can not be used without Samsung's authorization -...
Guides appear on the LCD monitor for 3 seconds when powered on or setting dial mode ( ✂ Y ou can set the specifi c time the guides will appear on the LCD monitor for. Select the desired time from [SETUP MENU] > [Guide Display]. - This Document can not be used without Samsung's authorization -...
Page 17
Shooting mode (Mode dial position) Drive mode/Extended Bracket ✔ ✛ Indicators [Metering type], [Focus Point Information], [White balance], and [Sensitivity] only appear ✌ when a setting other than the default setting is selected. - This Document can not be used without Samsung's authorization -...
Page 18
Press the INFO button in capture mode to display the capture function settings on the LCD monitor. ❉ ✁ ✂ ✄ ☎ ✆ ✁ ✝ ✞ ✟ ✠ ✡ ☛ ☞ ✄ ✂ ☎ ✡ ✟ - This Document can not be used without Samsung's authorization -...
Page 19
11. Colour Tone 26. Lens focal length 12. Saturation 27. Aperture Value 13. Contrast 28. Flash Exposure Value 14. Sharpness 29. Shutter Speed 15. Date and time 30. Exposure Compensation Value - This Document can not be used without Samsung's authorization -...
Page 20
❉ ✁ ✂ ✄ ☎ ✆ ✁ ✝ ✞ ✟ ✠ ✡ ☛ ☞ ✄ ✂ ☎ ✡ ✟ ✌ Y ou can change the information initially displayed by pressing the playback button ( - This Document can not be used without Samsung's authorization -...
Page 21
12. Focus point information 24. Shutter Speed 13. Exposure Compensation Value Indicators 5 (Flash mode) and 15 (Flash compensation Value) only appear when the image was ✁ taken with flash. - This Document can not be used without Samsung's authorization -...
Page 22
Capture quality (Image fi le type) ✄ P layback DPOF settings Indicator for Brightness Histogram and RGB Histogram Histogram (R) Histogram (G) Histogram (B) ✄ ✄ Y Histogram R GB Histogram Histogram (Brightness) - This Document can not be used without Samsung's authorization -...
Page 23
If the lighting conditions are too bright to check the subject by using the LCD, Dark Bright checking the histogram will enable more precise exposure control for the shots. Distribution of brightness - This Document can not be used without Samsung's authorization -...
✶ ✶ ✼ ✶ ✻ ✷ ✸ ✁ ✺ ✻ ✽ ✶ ✸ ✶ ✁ ✶ ✺ ✼ ✂ ✶ ✵ ✶ ✶ ✶ ✷ - This Document can not be used without Samsung's authorization -...
Page 25
In the M mode, the exposure value can be different. In the Sensitivity priority mode / Shutter & Aperture Priority mode, ISO sensitivity will display. 15. OIS (Optical Image Stabilization) indicator 16. AF Frame 17. Focus point - This Document can not be used without Samsung's authorization -...
T he following information appears in the LCD panel on top of the camera. ✶ ✁ ✶ ✂ ✶ ✄ ✶ ✶ ✶ ☎ ✶ ✄ ✽ ✾ ✻ ✼ ✂ ✁ ✹ - This Document can not be used without Samsung's authorization -...
Page 27
7. Displays the ISO sensitivity 8. RAW/RAW+ button in use 9. Battery status 10. Exposure Bar 11. Exposure compensation 12. Flash Exposure Compensation indicator 13. Auto Bracket 14. Shutter speed - This Document can not be used without Samsung's authorization -...
. SPECIFICATION 11. CONNECTION DIAGRAM SD/SDHC/MMC Card Card Reader TV Monitor IBM / MAC Lap top - This Document can not be used without Samsung's authorization -...
You can also edit and save the still images. This software is only compatible with Windows. ✁ U sing Samsung RAW Converter 2.0, you can convert a RAW (*.dng) le into a JPEG or TIFF fi le format. ✂ Y ou should allow 5~10 seconds for running the automatic setup program according to the capability of your computer.
PC and can be edited by an image editing program. 1. Install the Digimax Master by following the instructions shown on your PC monitor. Click Click - This Document can not be used without Samsung's authorization -...
Page 31
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 32
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 33
If you have installed the camera driver, the [Found New Hardware Wizard] may not open. ✁ If the download window of Digimax Master opens after starting Samsung Master, the camera driver ✁ was setup successfully.
The camera may malfunction when it is connected to the PC at the same time as Case 5 another USB cable. In this case, disconnect the other USB cable, and connect only one USB cable to the PC. - This Document can not be used without Samsung's authorization -...
Page 35
When the camera is connected to the USB port located on the front of the ✂ Case 9 computer, the computer may not recognise the camera. Connect the camera to the USB port located on the back of the computer. - This Document can not be used without Samsung's authorization -...
Page 36
. EXPLODED VIEW AND PART LIST 1. GX-20 : Fig. 1 - This Document can not be used without Samsung's authorization -...
Page 37
. EXPLODED VIEW AND PART LIST 2. GX-20 : Fig. 2 - This Document can not be used without Samsung's authorization -...
AD81-05847A Mount ring GX-10-A104 A107 AD81-05848A Mount lock button GX-10-A107 A115 AD81-05849A AM Selecting slide plate assy. GX-10-0-A115 A117 AD81-05850A RAW button base GX-10-A117 A141 AD81-03454A Solder stand GX-1S-A141 - This Document can not be used without Samsung's authorization -...
Page 41
GX-10-A213 A214 AD81-05880A SD card seal GX-1S-A214 A217 AD81-05881A SD card cover spring GX-10-A217 A218 AD61-03316A Lining board C A220 AD63-02313A I-LCD cushion A A221 AD63-02313A I-LCD cushion B - This Document can not be used without Samsung's authorization -...
Page 42
SR guide plate GX-10-A272 A273 AD81-05913A Guide plate GX-10-A273 A281 AD63-01753A Connector cover A281-1 AD63-02338A Double-sided Tape 1.2x8.5 A281-2 AD63-02337A Double-sided Tape 1.2x28 A282 AD81-05915A Card cover shaft GX-10-A282 1C3,1D7 - This Document can not be used without Samsung's authorization -...
Page 43
A337 AD81-05939A Photometry switch lever GX-10-A337 A338 AD81-05940A Lever click spring GX-10-A338 A339 AD81-05941A Lever brush GX-10-A339 A340 AD81-05942A O-ring 18x1 GX-10-A340 A341 AD81-05943A Round shape double-sided tape GX-10-A341 - This Document can not be used without Samsung's authorization -...
Page 44
AD63-03345A Battery cover A413 AD81-05973A Battery cover spring GX-10-A413 A415 AD66-00615A Battery cover lock claw 2G6,2G7 A417 AD81-05975A Battery cover click spring GX-10-A417 A418 AD61-03792A Battery cover handle plate - This Document can not be used without Samsung's authorization -...
Page 45
GX-10-M15 AD81-06005A SI holder GX-10-M51 AD81-06006A SI Mirror sheet assy. GX-10-0-M52 AD81-02673A SI cover GX-1S-M53 AD81-01157A SI prism molt GX-1S-M54 AD81-06007A SI spring GX-10-M55 M301 AD81-06008A Eyepiece frame GX-10-M301 - This Document can not be used without Samsung's authorization -...
Page 46
Flash frame shaft B GX-10-Q8 AD81-06037A Pop-up spring GX-10-Q9 AD81-06038A Flash frame shaft GX-10-Q10 AD81-06039A F Case waterproof sheet A GX-10-Q11 AD81-06040A F Case waterproof sheet B GX-10-Q12 AD81-06041A Flash window GX-10-Q20 - This Document can not be used without Samsung's authorization -...
Page 47
T940 AD92-00641A AF/MF select circuit block T970 AD92-00639A SD card circuit block AD81-06064A SD card cover GX-10-U1 AD81-01103A Cover retainer screw F GX-1S-A69 AD81-06066A TB wheel retainer screw GX-10-U4 - This Document can not be used without Samsung's authorization -...
Page 48
PET sheet 4x4 GX-10-U13 AD81-06076A Insulating tape 12x20 GX-10-U14 AD63-03318A F tape 6x10 AD63-03319A PVF tape 3.8x10 (0.08) 4D6,4EI AD63-03320A PVF tape 8x12 AD81-08760A Release SW 3722-002788 USB terminal - This Document can not be used without Samsung's authorization -...
Page 49
Double stick tape 6x8 1G4,1H3 DT22 AD63-03328A Double stick tape 9x50 DT24 AD63-03327A Double stick tape 11x42 DT25 AD63-03326A Double stick tape 17x45.3 DT25 AD63-03326A Double stick tape 17x45.3 - This Document can not be used without Samsung's authorization -...
. EXPLODED VIEW AND PART LIST 5. PACKING ITEM_GX-20 - This Document can not be used without Samsung's authorization -...
Page 51
U_MANUAL_GX-20_ENG Exclusive AD68-01905A U_MANUAL_GX-20_GER Exclusive AD68-01906A U_MANUAL_GX-20_FRA Exclusive AD68-01907A U_MANUAL_GX-20_SPA Exclusive AD68-01908A U_MANUAL_GX-20_ITA Exclusive AD68-01909A U_MANUAL_GX-20_DUT Exclusive AD68-01910A U_MANUAL_GX-20_RUS Exclusive AD68-01911A U_MANUAL_GX-20_CHI_S Exclusive AD68-01912A U_MANUAL_GX-20_SWE Exclusive AD68-01913A U_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 52
Q_MANUAL_GX-20_ENG Exclusive AD68-02662A Q_MANUAL_GX-20_GER Exclusive AD68-02663A Q_MANUAL_GX-20_FRA Exclusive AD68-02664A Q_MANUAL_GX-20_SPA Exclusive AD68-02665A Q_MANUAL_GX-20_ITA Exclusive AD68-02666A Q_MANUAL_GX-20_DUT Exclusive AD68-02667A Q_MANUAL_GX-20_RUS Exclusive AD68-02668A Q_MANUAL_GX-20_CHI_S Exclusive AD68-02669A Q_MANUAL_GX-20_SWE Exclusive AD68-02670A Q_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 53
Common 6801-001675 WARRANTY CARD_TSOE(CHINA)_PRODUCT Common 6801-001663 AS_CENTER_MANUAL_TSEO_S Common 6801-001664 LOCAL_WARRANTY_CARD_INDIA Common 6801-001665 LOCAL_WARRANTY CARD_ITALIA Common 6801-001681 WARRANTY CARD_CANADA Common AD68-02558A PRC_CARD_RUSSIA Common AD81-00883A LI-ION BATTERY_SLB-1674 Exclusive AD81-06277A CHARGER_SBC-L6 Exclusive - This Document can not be used without Samsung's authorization -...
. WIRING DIAGRAM - This Document can not be used without Samsung's authorization -...
Page 55
S300-T770 GREEN Q100-Q200 BROWN S300-T770 BROWN Q100-Q200 BLACK T770-T100 BLACK Q100-Q200 T770-T100 WHITE Q104-Q110 BLUE T770-T100 Q200-T770 YELLOW T770-T100 BLACK Q200-T770 VIOLET T770-T100 BLUE Q200-T100 GREEN Q200-T100 PINK Q200-T100 - This Document can not be used without Samsung's authorization -...
. FIRMWARE 1. Firmware Basic Version Check 1. Turn on the camera. 2. Turn on the camera while pressing the menu button. 3. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Right click the mouse on the "download the program file" button and then select "Save as (A)... ". ✁ 3. Insert a memory card and leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 58
. FIRMWARE 4. Turn on the camera. 5. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Check that the name of the firmware file is "FWGX20B.BIN". 2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card for firmware into the camera. - This Document can not be used without Samsung's authorization -...
Page 60
M ENU b utto . 6. If the following indication appears ✁ ✂ on the LCD monitor, select Y ES using the direction keys and press the OK button. - This Document can not be used without Samsung's authorization -...
Page 61
. FIRMWARE The firmware upgrade starts. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. - This Document can not be used without Samsung's authorization -...
Page 62
When the firmware upgrade is completed, the camera is set back to the original factory settings (language, date, time). Readjustments for each item are not needed, as the firmware upgrade is not relevant to the data related to adjustments. - This Document can not be used without Samsung's authorization -...
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (firmware for replacing the main board) into the camera. - This Document can not be used without Samsung's authorization -...
Page 64
. FIRMWARE 4. leave the cover open. 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
Page 65
The firmware upgrade starts for replacing the main board. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. Removing the current firmware…. - This Document can not be used without Samsung's authorization -...
Page 66
Writing new firmware…. 8. When the upgrade is completed, the camera's power is turned off automatically. After the firmware upgrade for replacing the main board, run the EEPROM PATCH. - This Document can not be used without Samsung's authorization -...
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (two files for EEPROM PATCH) into the camera. 4. leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 68
. FIRMWARE 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
After the firmware upgrade for replacing the main board and the execution of the EEPROM PATCH are completed, make sure to carry out adjustments. See “Adjustments” for detailed adjustments. - This Document can not be used without Samsung's authorization -...
. ADJUSTMENT 1. Preparation for Adjustments ✁ Preparation Equipment ✂ A djustments program software (written in CD-R) for 77012 (GX-20) ✂ P ersonal Computer (below PC for adjustment) OS : Windows XP SP2 CPU : above 1GHz RAM : above 512MB HD Bin Memory : above 500MB ✂...
Page 71
. ADJUSTMENT 2. Setting the computer and writing an SD card Insert the 77012 (GX-20) CD-R for adjustment into the CD-Rom drive of the computer. ✁ (77010£ P ENTAX K20D) ✂ Copy the 7 7010 folder from the CD-R onto the C drive. (Adjustment software main body) ✄...
Page 72
W hen the V B Run Time Set-up p rogram is not installed, double click on the “setup.exe” file in ✞ ✟ the° v b6run_cs_x.x.x° f older and execute the installation. - This Document can not be used without Samsung's authorization -...
LV checker (for checking LV values) ✂ 1. Computer Set-up 2 . Setting the computer in the P reparation section has to be completed. ☎ ✆ ☎ ✆ (Use the digital adjustment software.) - This Document can not be used without Samsung's authorization -...
Page 74
T urn on the camera and check that the camera is recognized by the PC. ✞ ☎ ✆ S et the light box to L V12 ✟ P osition the lens on the top center of the light box. - This Document can not be used without Samsung's authorization -...
Page 75
The digital adjustment screen appears. Click on the icon for calibration at the top left of the screen. ✞ The calibration screen appears. Click on the “Enter” key (or “START” button). ✟ (Release 15 times about for 35 secs.) - This Document can not be used without Samsung's authorization -...
Page 76
E nd the adjustments software by clicking on the [X] button (or [END] button ). ✄ ☎ ✆ S ee the E rror code table i n the manual for NG adjustment. - This Document can not be used without Samsung's authorization -...
Shutter speed adjustment according to the histogram ✂ K 20D_PDCAdj ✄ Initial settings Function test (Initialized at the factory) *SR check can be skipped if SR adjustment is completed. ✂ I nitialize Set ✄ - This Document can not be used without Samsung's authorization -...
S et the AF change lever to ( top position). ✝ C amera setting: mode dial “M”, OPS switch “ON” ✞ ✟ M ount the OPS unit adjustment plate ( ) on the body. - This Document can not be used without Samsung's authorization -...
Page 79
Double click on the K 20D SR Operation.exe file in the adjustment software folder and execute it. ✂ ✆ ✝ The adjustment screen appears. ✞ Click on the [Start] button. ✟ - This Document can not be used without Samsung's authorization -...
Page 80
✄ ☎ I f the T100 is replaced enter the CCD ID no. twice. ✆ Click on INPUT. ✝ C lick on the “Cancel” button when stopping the adjustment. - This Document can not be used without Samsung's authorization -...
Page 81
Check the “Unconnect” display, and end the adjustment by clicking on the [X] button. ✄ I f the adjustment is displayed as NG, the green turns into red. ✁ - This Document can not be used without Samsung's authorization -...
V isual C++Runtime2005 m ust be installed on the PC already. ✆ ✄ ☎ T he 77010 S R_GainForCS f older must be copied onto the hard disk. - This Document can not be used without Samsung's authorization -...
Page 83
Set the lighting to LV 10 to 12 without the surface of the chart spotted. ✄ Set the zoom ring of the D-XENON 50-200mm lens to 200mm and its distance ring to 2m. ☎ (Fix the four sections with tape to prevent vibration.) - This Document can not be used without Samsung's authorization -...
Page 84
✠ C heck C heck again that the distance is 2.0mm. Turn on the controller and turn the dial up to 1,000 rpm. Turn off the controller after checking. - This Document can not be used without Samsung's authorization -...
Page 85
Connect the camera to the PC using the USB cable, and turn it on. ✁ 3. Adjustment Double click on the “SR_GainForCS.exe” file in the 77010 S R_GainForCS folder. ✂ ✄ ☎ Start the adjustment by clicking on the “Execute” button. ✆ - This Document can not be used without Samsung's authorization -...
Page 86
T urn on the controller (1,000 rpm). Adjust the X direction by clicking on the “OK” button. ✂ T urn off the controller, and click on the “OK” button.(The following adjustment starts.) - This Document can not be used without Samsung's authorization -...
Page 87
Turn off the controller, and change the positions of the camera and the stage to the Y direction ✂ adjustment. ✄ IMPORTANT Handle the stage carefully, as it is heavy. Do not touch the black vibration plate. - This Document can not be used without Samsung's authorization -...
Page 88
C lick on [OK], and adjust the Y direction in the same way as the X direction adjustment. ☎ I f all the adjustments are completed, then the OK message appears. ✆ E nd the adjustments by clicking on the [X] button or [Quit] button. - This Document can not be used without Samsung's authorization -...
✁ F5.6 set plate for photometric standard lens (No.95901-D20 only) ✁ Side AF gradient adjustment tool (square) ✁ AF gradient adjustment tool (cross) ✁ Hexagonal driver 1.5mm (HD-M1.5) ✁ - This Document can not be used without Samsung's authorization -...
Page 90
✞ ✄ ☎ S et the SR (OIS) lever to O FF ✟ C onnect the camera to the PC using the USB cable and turn on the camera. - This Document can not be used without Samsung's authorization -...
Page 91
D ata initialization C AUTION Select , as the ✆ ✝ ✂ ✄ SR adjustment data is cleared. Replace the main board? Adjustment screen and all the items display - This Document can not be used without Samsung's authorization -...
Page 92
. ADJUSTMENT ✁ [ BV ADJUST] ✁ A djust [CCD POSITION ADJUST] ✁ A djust [AGC LEVEL ADJUST] ✂ P erform this after completing all the adjustments and checking.) - This Document can not be used without Samsung's authorization -...
Page 93
Click on the “Cl” icon, and disconnect the communication with the camera. (USB close) ✆ C heck Check that the USB IO is displayed as U nconnect ✝ ✞ ✄ ☎ Click on the “end” icon, and end the adjustment program. ✟ - This Document can not be used without Samsung's authorization -...
C lick on the "Op" icon and start the communication with the camera. Check that the USB IO is displayed as "connected". ✟ M ount the diaphragm set ring on the camera with the aperture open. - This Document can not be used without Samsung's authorization -...
Page 95
If there isn't a tool for the diaphragm set ring, a lens which can set the aperture to 1.4 can be used. Connect the camera to the EV tester. ✁ - This Document can not be used without Samsung's authorization -...
Page 96
C lick on the "2. EXPOSURE ADJUST - BV ADJUST" button. Enter the lens ID no. and click on "Input". ✂ S elect the type of the EV tester. - This Document can not be used without Samsung's authorization -...
Page 97
Set the EV tester to LV6 and click on the "OK" button. After the following message appears, change the set plate to an F5.6 set plate. Click on "OK" and continue with the adjustment. - This Document can not be used without Samsung's authorization -...
Page 98
A message “Set the EV tester to LV15” will appear. Set the EV tester to LV15 and click on the “OK” button. If the adjustment is completed, the following message will appear. Click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 99
. ADJUSTMENT The adjustment value is saved in the camera. Click on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
Page 100
If the shutter speed values change identically to the table above according to the changes of the LV values with the aperture stop of F8, the adjustment has been completed. Otherwise perform the adjustment again. - This Document can not be used without Samsung's authorization -...
☎ ✆ The adjustment screen appears. ✝ Click on the "Op" icon and start the communication with the camera. ✞ Check that the USB IO is displayed as "connected". - This Document can not be used without Samsung's authorization -...
Page 102
. ADJUSTMENT ✂ I nstall a cross gradient adjustment tool. Set the focus mode to MF. ✁ C onnect the camera (Cross installation) to the EV tester. - This Document can not be used without Samsung's authorization -...
Page 103
. ADJUSTMENT Click on the "3.AF AND REL ADJ - CCD POSITION ADJ - ADJUSTMENT" button. ✁ Click on the “DumpStart” button on Alpha-CROSS. ✂ - This Document can not be used without Samsung's authorization -...
Page 104
Set the LV value on the EV tester to 12 and click on the “OK” button. If the measurement values are displayed in green, it is normal. (Adjust the position of the AF sensor to make the sizes and shapes of the graphs uniform.) - This Document can not be used without Samsung's authorization -...
Page 105
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). Install the square gradient adjustment tool. ✁ - This Document can not be used without Samsung's authorization -...
Page 106
. ADJUSTMENT Click on the “DumpStart” button on Beta-SQUARE. Set the LV value on the EV tester to 12 and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 107
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). - This Document can not be used without Samsung's authorization -...
Page 108
. ADJUSTMENT ✁ I nstall a standard lens (50M F1.4). Set the distance from the camera mount plane to the AF chart no.1 to 1,954.5mm(=1.9545m) using the tripod. - This Document can not be used without Samsung's authorization -...
Page 109
. ADJUSTMENT Click on the “Start” button in “Focus”. Check the conditions of the camera and chart settings as below and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 110
If the centers of the graphs are moved to the red lines, then click on the “Next” button. If the measurement values are displayed in green, it is normal. - This Document can not be used without Samsung's authorization -...
Page 111
Turn the Allen wrench in the same direction for all three areas. If you turn each area in different directions, the gradient will change. You need to check the gradient or adjust it again. - This Document can not be used without Samsung's authorization -...
If there isn't a 35-80 F4-5.6 lens, a bundle lens can be used. Set the items as below if a bundle lens is used for adjustment. Focus MF mode, lens distance 55m, distance ring 0.4m. - This Document can not be used without Samsung's authorization -...
Page 113
Connect the camera to the EV tester. (Install a 35-80 lens or a bundle lens) ✁ Click on the “3. AF AND REL ADJ - CCD POSITION ADJ - POSITION CHECK” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 114
I f the AF sensor is positioned correctly, the following message will appear. Click on the “OK” button. If “NG” appears, then adjust the position of the AF sensor again. - This Document can not be used without Samsung's authorization -...
Page 115
. ADJUSTMENT Close the AF sensor position check screen by clicking on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
(similar to sensitivity of film). If the signal is weaker than the standard, it increases the level of the signal up to the standard. 1. Adjustment procedure ✁ I nstall a 50mm F1.4 lens on the camera. (Set the focus mode to MF.) - This Document can not be used without Samsung's authorization -...
Page 117
. ADJUSTMENT Connect the camera to the EV tester. (Install a 50m lens.) ✁ Click on the “3. AF AND REL ADJ - AGC LEVEL ADJUST” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 118
S elect the type of EV tester and adjust the LV values (light value, reference exposure value) in the following order 6, 7, 12 and 15 by clicking on the “AGC Adjust” button. If the adjustments are completed, click on the “Close” button. - This Document can not be used without Samsung's authorization -...
Install a Macro 50mm F2.8 lens to the camera. (Set the focus mode to MF, infinitive.) ✁ Connect the camera to the EV tester. (Install a 50m lens.) ✂ - This Document can not be used without Samsung's authorization -...
Page 120
C lick on the "Execute" button and start the adjustment. ✆ I f the adjustment is completed, the "OK" message will appear at the bottom left of the screen. - This Document can not be used without Samsung's authorization -...
Page 121
Click on the [X] button and end the adjustment. ✁ If an adjustment error occurs, the "NG" message and an error code will be displayed. ✂ E rror code table in the manual. ✄ ☎ - This Document can not be used without Samsung's authorization -...
The adjustment screen appears. ✝ Click on the “Enter” button after entering the temperature ( ) . ( : Use the mouse pointer to select “Fahrenheit”.) ✞ ✟ ✠ - This Document can not be used without Samsung's authorization -...
Page 123
If this state is maintained, the adjustment starts automatically. IMPORTANT Do not touch the camera or the chart during the adjustment. The adjustment has to be performed again if there is contact, even if it was OK. - This Document can not be used without Samsung's authorization -...
Page 124
A djust the position of the camera and the chart in the same way as the vertical sensor's adjustment. (Up and down direction). ✄ I f the adjustment is completed, then the “OK” message appears. ☎ C lick on the [X] button and end the adjustment. - This Document can not be used without Samsung's authorization -...
Turn on the camera and check that the hot plug icon is displayed on the PC. ☎ Double click on the "K20D_PDCAdj01.exe" file in the E XE folder. ✆ ✝ ✞ - This Document can not be used without Samsung's authorization -...
Page 126
C lick on the “Op” icon and start the communication with the camera. Check that the USB IO is displayed as “connected”. ✄ C lick on the “6. BATTERY LEVEL ADJUST” button. - This Document can not be used without Samsung's authorization -...
Page 127
If the adjustment is completed, then click on the “CI” button. ✂ Check that the USO IO is changed to “Unconnect” from “Connect”. Click on the “end” button and end the program. ✄ - This Document can not be used without Samsung's authorization -...
A djust the brightness and the color temperature using the color thermometer for photography and the LV checker as below. Light Brightness Color temperature LV12 LV12.00Ev ±0.50 2,856K ±30 LV11 LV11.00Ev ±0.01 - This Document can not be used without Samsung's authorization -...
Page 129
Cover the light box (Brightness measurement equipment (light source A, color temperature 2,850K±10, ✟ brightness LV11.00)) with a light blocking cover and position the lens in the middle of the light box. - This Document can not be used without Samsung's authorization -...
Page 130
C lick on “Yes (Y)” if the lens no. is entered correctly. ✞ H it the "Enter" key (or click on the "START" button) and start the adjustment. (Start the adjustment according to the instructions.) - This Document can not be used without Samsung's authorization -...
Page 131
If all the adjustments are completed, then the “OK” message appears. ✁ Click on the [X] button (or [END] button) and end the adjustment program. ✂ (Adjustment time: approx. 3 mins 30 secs). - This Document can not be used without Samsung's authorization -...
I f all the adjustments are completed, then the "OK" message appears. ✠ C lick on the [X] button (or [END] button) and end the adjustment program. (Adjustment time: approx. 70secs). - This Document can not be used without Samsung's authorization -...
: standard (initial values) P layback Quick view 5secs, set the view display as histogram ✆ ✝ C ustom Allows release apart from the diaphragm ring A. ✆ ✝ - This Document can not be used without Samsung's authorization -...
Page 134
✁ S et the EV tester to LV9. ✂ S et the shutter speed to Tv 500. ✄ S et the 50M F1.4 lens aperture stop to "open" (F1.4). - This Document can not be used without Samsung's authorization -...
Page 135
The peak has to be in the following range of the histogram when looking at the images on the LCD monitor. If it is displayed as NG, check the settings again, or perform the BV adjustment and digital adjustment (CCD) again. - This Document can not be used without Samsung's authorization -...
Page 136
Measure the differences (mm) on the LCD monitor with a ruler. IMPORTANT This has to be checked in front of the camera. Do not damage (scratch) the LCD screen. - This Document can not be used without Samsung's authorization -...
Page 137
Tv500 (standard). Select a histogram zone (A to D) corresponding to the peak position of Tv4000 from the following ✁ figure. (The example above corresponds to type B.) - This Document can not be used without Samsung's authorization -...
Page 138
(Find the shutter speed from the conversion table for the example above. The histogram zone is B. The difference is +1.5mm to the right. Therefore the shutter speed value is 0.273mS) Conversion table of shutter speed (Apply to GX-10•GX-1S•GX-1L) - This Document can not be used without Samsung's authorization -...
Page 139
Click on the “Op” icon and start the communication with the camera. ✞ Check that the USB IO is displayed as “connected”. Click on the “7. SHUTTER SPEED ADJUST” button. ✟ - This Document can not be used without Samsung's authorization -...
Page 140
. ADJUSTMENT Select ''Shutter Tester for 1/4000 Sec” from “Select”. Ignore the message, and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 141
If it is displayed as NG, enter the default value 0 .25 in the “Input Data” section and end the procedure. ✁ ✂ (To validate the converted data.) If it is NG, check the relevant adjustment items again. - This Document can not be used without Samsung's authorization -...
Page 142
. ADJUSTMENT If the adjustment is completed, the values are saved in the camera. Click on the “Close” button and close the adjustment window. - This Document can not be used without Samsung's authorization -...
Page 143
. ADJUSTMENT Click on the “CI” button. Check that the USB IO has been changed to “Unconnect” from “Connect”. ✁ Click on the “end” button and end the program. ✂ - This Document can not be used without Samsung's authorization -...
Remove the super-imposer PCB as shown in the following figure. ✁ C onnect the lead wires to the 0-O170 (SI-LED) as shown in the following figure. IMPORTANT Do not apply pressure on the solder of 0-O170. - This Document can not be used without Samsung's authorization -...
Page 145
Apply DC3.2 V and check if the 11 SI-LEDs are turned on and check the positions. ✁ A djustment 1 Loosen the two screws which ✂ ✄ ☎ hold the 0-O170. … Remove the adhesive (5 areas) for the screws. - This Document can not be used without Samsung's authorization -...
Page 146
A fter the adjustment, apply the screw adhesive to the five areas, and remove the lead wires. ✝ A ttach the mount cover to prevent the SI-LEDs from being affected during the work. - This Document can not be used without Samsung's authorization -...
Aim the light from the penlight onto the AE sensor and find a position where the shape of the AE sensor ✂ is shown on the 1st mirror by changing the angle of the penlight. - This Document can not be used without Samsung's authorization -...
Page 148
✄ T ighten the screws and check it again. ☎ A fter the adjustment, apply the adhesive to the two areas of the screws for the AE sensor (0-J100). - This Document can not be used without Samsung's authorization -...
Wearing the band which cuts off the electric current and do the reparing PCB type Where the blocking static electricity mat is on by preventing the defect of parts. CONTACT type Be careful of defect and change by pincette. - This Document can not be used without Samsung's authorization -...
Do not leave screws, steel balls or magnetic cards near the OIS block because there is a strong magnet in the OIS block when the cover is open. ✂ F ive screws ✄ E ight screws ☎ A 401•Battery cover - This Document can not be used without Samsung's authorization -...
Page 151
. SERVICE INFORMATION Caution The OIS block protrudes at the bottom. Don't cause any impact to this area. 2> A301 (Top Cover) Screw•O-ring ✁ Screw…pop up the STROBO. ✂ - This Document can not be used without Samsung's authorization -...
Page 152
. SERVICE INFORMATION ✁ S crew ✂ S crew…flip the rubber. ✄ S crew (inside the battery room) ☎ T wo screws - This Document can not be used without Samsung's authorization -...
Page 153
Discharging the strobe's main condenser. ✁ Lift up the A301 and discharge the electricity, charged in the main condenser, with resistance. (The white lead wire and the brown lead wire on the T750). - This Document can not be used without Samsung's authorization -...
Page 154
. SERVICE INFORMATION ✁ F ive lead wires. ✂ R emove the T51 PCB from the connector (sliding lock). ✄ A 301 ☎ A 27 (waterproof sheet) - This Document can not be used without Samsung's authorization -...
Page 155
Remove the T920 PCB from the connector ✁ (plug type). Set the AF lever to MF. ✂ Two screws ( ✄ ☎ Screw…flip the grip rubber. ✆ Screw ✝ A150 ✞ - This Document can not be used without Samsung's authorization -...
Page 156
: Install the mount cover to prevent damage to the SI-LED•TV dial ✁ A 201…Beware of the terminal section at the end and remove the rear cover by lifting the bottom a little. ✄ T wo screws ☎ M 311 - This Document can not be used without Samsung's authorization -...
Page 157
Remove the PCB from the connector (4ea, plug type) ✆ Caution Don't apply excessive pressure on the PCB of the CCD block as this may affect its performance. Ensure that the PCB is not bent. - This Document can not be used without Samsung's authorization -...
Page 158
Caution Beware that the PCB on the OIS block may be damaged if the main board (T100) is moved too far from the body of camera. - This Document can not be used without Samsung's authorization -...
Page 159
. SERVICE INFORMATION Remove the PCB from the connector (plug type). ✁ T100 ✂ - This Document can not be used without Samsung's authorization -...
Page 160
. SERVICE INFORMATION 5> 0-T970 (SD Circuit Block) ✁ T wo lead wires (red, white) ✂ T hree screws ✄ 0 -T970 - This Document can not be used without Samsung's authorization -...
Page 161
6> 0-T770·0-A51 (PZ Circuit Block·Tripod Holder) Two lead wires (white, brown) ✁ Screw ✂ When removing the 0-T770 and lead wires, be careful of the double sided tape. ✄ Four screws ☎ 0-A51 ✆ - This Document can not be used without Samsung's authorization -...
Page 162
OIS block. ✂ D on't put excessive pressure on the moving parts of the OIS block. ✂ D on't put excessive pressure on the PCB of the OIS block. - This Document can not be used without Samsung's authorization -...
Page 163
. SERVICE INFORMATION 7> O201 (LCD Block) Remove the PCB from the A E-L butto. ✁ ✂ ✄ Screw ☎ A TY screw ✆ - This Document can not be used without Samsung's authorization -...
Page 164
R emove the T700 PCB from the connector (flip lock). ✆ R emove the BT (6 x 15) from the grip area and pull out the four lead wires. - This Document can not be used without Samsung's authorization -...
Page 165
. SERVICE INFORMATION Flip two PCBs to the outside and place the LCD block (O201) back into position. ✁ Remove the soldering from the three lead wires. ✂ O201 ✄ - This Document can not be used without Samsung's authorization -...
Page 166
R emove the soldering from the three lead wires. ✄ R emove the PCB near the release switch and the green button. ☎ S crew ✆ A TY screw ✝ A 350 - This Document can not be used without Samsung's authorization -...
Page 167
9> 0-T700 (Top Right Relay Board) 12 Lead wires (not identical to wiring 76830 G 119 · G 100 · A 105 · E 000) ✁ ✂ ✄ ☎ ✁ ✆ - This Document can not be used without Samsung's authorization -...
Page 168
. SERVICE INFORMATION ✁ F our soldering areas on the T71 PCB. ✂ R emove the PCB from the DT. - This Document can not be used without Samsung's authorization -...
Page 169
. SERVICE INFORMATION Two TY screws ✁ Two screws ✂ T700 ✄ - This Document can not be used without Samsung's authorization -...
Page 170
. SERVICE INFORMATION 10> 0-T750 (Top Left Relay Board) ✁ S even soldering areas on the O170 PCB ✂ F our lead wires ✄ S even lead wires - This Document can not be used without Samsung's authorization -...
Page 171
Two TY screws ✂ Remove the connector from the Q200. ✄ Remove the PCB from the RAW button. ☎ Remove the PCB from the penta area. ✆ T750 ✝ - This Document can not be used without Samsung's authorization -...
Page 172
✁ A TY screw ✂ A 117 ✄ S et the AF switch to the bottom position. ☎ A TY screw ✆ 0 -T940…remove carefully, beware of the switch. - This Document can not be used without Samsung's authorization -...
Page 173
. SERVICE INFORMATION A TY screw ✁ TY-CNL screw ✂ CSM screw ✄ Q200. Related parts ☎ - This Document can not be used without Samsung's authorization -...
Page 174
A423 (mask) ✄ C NL-D ☎ L ift up the T901 PCB. ✆ C NL-D Ä1.7 x 2.5 (Two) ✝ T Y-CSM ✞ T Y-CNL-D Ä1.7 x 4.0 (Three) - This Document can not be used without Samsung's authorization -...
Page 175
. SERVICE INFORMATION 0-A3 ✁ - This Document can not be used without Samsung's authorization -...
Page 176
. SERVICE INFORMATION 13> T901 (Bottom Relay Board) ✁ T wenty soldering areas on the T301·M100 ✂ T 901·two lead wires ✄ S crew ☎ A 141 - This Document can not be used without Samsung's authorization -...
Page 177
. SERVICE INFORMATION 14> A6 (Left Large Plate·Related Parts) CNL-D ✁ TY-CNL-D ✂ Four TY-CSM screws ✄ ☎ - This Document can not be used without Samsung's authorization -...
✁ A 6 … Tidy up the lead wire and the flexible PCB as shown in the figure. ✂ F our TY-CSM1.7x4.0 screws ✄ T Y-CNL-D1.7x4.0 ☎ C NL-D1.7x2.5 - This Document can not be used without Samsung's authorization -...
Page 179
. SERVICE INFORMATION 2> T901 (Bottom relay board) A141 ✁ TY-CNL-1.7x3.5 ✂ T901(Two red and black lead wires) ✄ Solder on the twenty land areas of the T301·100 flexible PCB. ☎ - This Document can not be used without Samsung's authorization -...
Page 180
P ut the O-A3into the body of the camera while tidying up the lead wires and the flexible PCB. ✄ T hree TY-CNL-D1.7x4.0 ☎ T wo CNL-D1.7x2.5 ✆ T Y-CSM1.7x4.0 ✝ C onnect the theT901 flexible PCB to the 0-A3. - This Document can not be used without Samsung's authorization -...
Page 181
. SERVICE INFORMATION A423 (Mask) ✁ ✂ CNL-D1.7x1.6 (2 ✄ ☎ Attach the U12 (8x12) firmly. ✆ Tidy up the two lead wires (red·black, S250). ✝ - This Document can not be used without Samsung's authorization -...
Page 182
✝ T Y-CNL-D1.7x3.5 ✞ S et the AF lever to the middle (AF.S). ✟ 0 -T940 … Install this without damaging to the SW section. ✠ T Y-CNL-D1.7x3.0 - This Document can not be used without Samsung's authorization -...
Page 183
Fix the flexible PCB with the DT (10x5). ✞ Connect the connector of the Q200. ✟ Fix the flexible PCB on the RAW button with ✠ the DT (8x4). - This Document can not be used without Samsung's authorization -...
Page 184
. SERVICE INFORMATION ✁ S older on the seven land areas of the O170 flexible PCB. ✂ F our lead wires ✄ S even lead wires - This Document can not be used without Samsung's authorization -...
Page 185
6> 0-T700 (Top right relay board) T700 … Tidy up as shown in the figure. ✁ ✂ Two CNL-D1.7x1.6 ✄ Two TY-CNL-D1.7x3.5 ☎ Fix the flexible PCB with the DT (10x4). ✆ - This Document can not be used without Samsung's authorization -...
Page 186
. SERVICE INFORMATION ✁ S older on the four land areas of the T71 flexible PCB. ✂ T welve lead wires - This Document can not be used without Samsung's authorization -...
Page 187
Fix the flexible PCBs on the F release SW and the green button SW section with the O207 (DT) and ☎ the DT (5x5). Solder on the three lead wires. ✆ Use the BT (6x15) for the two lead wires (A14 battery armature). ✝ - This Document can not be used without Samsung's authorization -...
Page 188
U se the BT (6x15) for the front four lead wires (T950). ✝ C onnect the O100 flexible PCB to the connector. (Flop lock) ✞ C onnect the T700 flexible PCB to the connector. (Flip lock) - This Document can not be used without Samsung's authorization -...
Page 189
. SERVICE INFORMATION CNL-D1.7x2.5 ✁ Two TY-CNL-D1.7x4.5 ✂ Fix the A E-L flexible PCB with the DT(5x5). ✄ ☎ ✆ - This Document can not be used without Samsung's authorization -...
Page 190
0 -T770 ☎ U 7 screw ✆ U se the DT (6x15) for the lead wires from the 0-T770. ✝ S older on the two lead wires (brown, white). - This Document can not be used without Samsung's authorization -...
Page 191
0-T970 … Tidy up the lead wires as shown in the figure. ✁ Three TY-CNL-D1.7x3.5 ✂ ✂ Solder on the two lead wires (red, white). ✄ Attach the T88. ☎ ✆ Attach the T89. ✝ Attach the U13 (11x20). ✞ - This Document can not be used without Samsung's authorization -...
Page 192
✝ C onnect the flexible PCB to the connector. (Plug type) ✞ C onnect the connector by pushing the T100 onto the camera body. (Plug type) - This Document can not be used without Samsung's authorization -...
Page 193
. SERVICE INFORMATION Three CNL-D1.7x2.5 ✁ ✂ TY-CNL-D1.7x3.5 ✄ - This Document can not be used without Samsung's authorization -...
Page 194
✄ S older on the twenty-one lead wires. ☎ U 8 (3.8x10) ✆ U 3 (BT 6x15) … Three sections ✝ A ttach the T99 onto the land area. - This Document can not be used without Samsung's authorization -...
Page 195
Check if there is twisting, peeling, cracking or damage to each sealing. Ensure that the dial doesn't make contact with the waterproof sheet when turning the front digital dial. Front·Rear digital dial ✁ - This Document can not be used without Samsung's authorization -...
Page 196
. SERVICE INFORMATION ✁ M 311 ✂ A 150 - This Document can not be used without Samsung's authorization -...
Page 197
. SERVICE INFORMATION A201 ✁ - This Document can not be used without Samsung's authorization -...
Page 198
. SERVICE INFORMATION ✁ A 301 ✂ A 401 - This Document can not be used without Samsung's authorization -...
Page 199
A98 (O-ring) … Ensure that the O-ring is installed without a cave-in, crack or damage. ☎ U1(=27370-A115) ✆ A201 … Install the A201 slowly from the bottom. (Be careful of the external ports.) ✝ - This Document can not be used without Samsung's authorization -...
Page 200
✂ C NL-D1.7x3.0 ✄ T Y-CNL-D1.7x5.5 … Attach a rubber grip. ☎ A 172(Two TY 1.7x4.5 screws) ✆ C onnect the T920 flexible PCB to the connector. (Plug type) - This Document can not be used without Samsung's authorization -...
Page 201
* The armature of the main SW must not be deformed. * Apply the G151 onto the main SW land. A27(sheet) … no cave-ins or cracks ✁ A301 ✂ - This Document can not be used without Samsung's authorization -...
Page 202
A 171 (TY 1.7x4.0 screw)·A304 (O-ring) ✝ A 171 … Pop up the strobe. ✞ T Y-CNL-D1.7x7.0 … Attach a rubber. ✟ A 173 ✠ T Y-CNL-D1.7x8.0 Ni (inside the battery room) - This Document can not be used without Samsung's authorization -...
Page 203
. SERVICE INFORMATION 16> A401 (Bottom parts) Check Check the installation of the sealing parts. A401·Battery cover ✁ A174 (Eight 1.7x4.0 screws) ✂ A172 (Five TY 1.7x4.5 screws) ✄ - This Document can not be used without Samsung's authorization -...
Page 204
Any unauthorized use of Manual can be punished under applicable International and/or domestic law. International and/or domestic law. - This Document can not be used without Samsung's authorization - - This Document can not be used without Samsung's authorization -...
Page 205
You can also edit and save the still images. This software is only compatible with Windows. ✁ U sing Samsung RAW Converter 2.0, you can convert a RAW (*.dng) le into a JPEG or TIFF fi le format. ✂ Y ou should allow 5~10 seconds for running the automatic setup program according to the capability of your computer.
Page 206
PC and can be edited by an image editing program. 1. Install the Digimax Master by following the instructions shown on your PC monitor. Click Click - This Document can not be used without Samsung's authorization -...
Page 207
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 208
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 209
If you have installed the camera driver, the [Found New Hardware Wizard] may not open. ✁ If the download window of Digimax Master opens after starting Samsung Master, the camera driver ✁ was setup successfully.
Page 210
The camera may malfunction when it is connected to the PC at the same time as Case 5 another USB cable. In this case, disconnect the other USB cable, and connect only one USB cable to the PC. - This Document can not be used without Samsung's authorization -...
Page 211
When the camera is connected to the USB port located on the front of the ✂ Case 9 computer, the computer may not recognise the camera. Connect the camera to the USB port located on the back of the computer. - This Document can not be used without Samsung's authorization -...
Page 212
. EXPLODED VIEW AND PART LIST 1. GX-20 : Fig. 1 - This Document can not be used without Samsung's authorization -...
Page 213
. EXPLODED VIEW AND PART LIST 2. GX-20 : Fig. 2 - This Document can not be used without Samsung's authorization -...
Page 214
. EXPLODED VIEW AND PART LIST 3. GX-20 : Fig. 3 - This Document can not be used without Samsung's authorization -...
Page 215
. EXPLODED VIEW AND PART LIST 4. GX-20 : Fig. 4 - This Document can not be used without Samsung's authorization -...
Page 216
AD81-05847A Mount ring GX-10-A104 A107 AD81-05848A Mount lock button GX-10-A107 A115 AD81-05849A AM Selecting slide plate assy. GX-10-0-A115 A117 AD81-05850A RAW button base GX-10-A117 A141 AD81-03454A Solder stand GX-1S-A141 - This Document can not be used without Samsung's authorization -...
Page 217
GX-10-A213 A214 AD81-05880A SD card seal GX-1S-A214 A217 AD81-05881A SD card cover spring GX-10-A217 A218 AD61-03316A Lining board C A220 AD63-02313A I-LCD cushion A A221 AD63-02313A I-LCD cushion B - This Document can not be used without Samsung's authorization -...
Page 218
SR guide plate GX-10-A272 A273 AD81-05913A Guide plate GX-10-A273 A281 AD63-01753A Connector cover A281-1 AD63-02338A Double-sided Tape 1.2x8.5 A281-2 AD63-02337A Double-sided Tape 1.2x28 A282 AD81-05915A Card cover shaft GX-10-A282 1C3,1D7 - This Document can not be used without Samsung's authorization -...
Page 219
A337 AD81-05939A Photometry switch lever GX-10-A337 A338 AD81-05940A Lever click spring GX-10-A338 A339 AD81-05941A Lever brush GX-10-A339 A340 AD81-05942A O-ring 18x1 GX-10-A340 A341 AD81-05943A Round shape double-sided tape GX-10-A341 - This Document can not be used without Samsung's authorization -...
Page 220
AD63-03345A Battery cover A413 AD81-05973A Battery cover spring GX-10-A413 A415 AD66-00615A Battery cover lock claw 2G6,2G7 A417 AD81-05975A Battery cover click spring GX-10-A417 A418 AD61-03792A Battery cover handle plate - This Document can not be used without Samsung's authorization -...
Page 221
GX-10-M15 AD81-06005A SI holder GX-10-M51 AD81-06006A SI Mirror sheet assy. GX-10-0-M52 AD81-02673A SI cover GX-1S-M53 AD81-01157A SI prism molt GX-1S-M54 AD81-06007A SI spring GX-10-M55 M301 AD81-06008A Eyepiece frame GX-10-M301 - This Document can not be used without Samsung's authorization -...
Page 222
AD81-06036A Flash frame shaft B GX-10-Q8 AD81-06037A Pop-up spring GX-10-Q9 AD81-06038A Flash frame shaft GX-10-Q10 AD81-06039A F Case waterproof sheet A GX-10-Q11 AD81-06040A F Case waterproof sheet B GX-10-Q12 - This Document can not be used without Samsung's authorization -...
Page 223
T921-2 AD63-02361A BACK_FPCB_TAPE T921-3 6003-001637 TY-CNL-D1.7X3.0 T940 AD92-00641A AF/MF select circuit block T970 AD92-00639A SD card circuit block AD81-06064A SD card cover GX-10-U1 AD81-01103A Cover retainer screw F GX-1S-A69 - This Document can not be used without Samsung's authorization -...
Page 224
PET sheet 4x4 GX-10-U13 AD81-06076A Insulating tape 12x20 GX-10-U14 AD63-03318A F tape 6x10 AD63-03319A PVF tape 3.8x10 (0.08) 4D6,4EI AD63-03320A PVF tape 8x12 AD81-08760A Release SW 3722-002788 USB terminal - This Document can not be used without Samsung's authorization -...
Page 225
Double stick tape 6x8 1G4,1H3 DT22 AD63-03328A Double stick tape 9x50 DT24 AD63-03327A Double stick tape 11x42 DT25 AD63-03326A Double stick tape 17x45.3 DT25 AD63-03326A Double stick tape 17x45.3 - This Document can not be used without Samsung's authorization -...
Page 226
. EXPLODED VIEW AND PART LIST 5. PACKING ITEM_GX-20 - This Document can not be used without Samsung's authorization -...
Page 227
U_MANUAL_GX-20_ENG Exclusive AD68-01905A U_MANUAL_GX-20_GER Exclusive AD68-01906A U_MANUAL_GX-20_FRA Exclusive AD68-01907A U_MANUAL_GX-20_SPA Exclusive AD68-01908A U_MANUAL_GX-20_ITA Exclusive AD68-01909A U_MANUAL_GX-20_DUT Exclusive AD68-01910A U_MANUAL_GX-20_RUS Exclusive AD68-01911A U_MANUAL_GX-20_CHI_S Exclusive AD68-01912A U_MANUAL_GX-20_SWE Exclusive AD68-01913A U_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 228
Q_MANUAL_GX-20_ENG Exclusive AD68-02662A Q_MANUAL_GX-20_GER Exclusive AD68-02663A Q_MANUAL_GX-20_FRA Exclusive AD68-02664A Q_MANUAL_GX-20_SPA Exclusive AD68-02665A Q_MANUAL_GX-20_ITA Exclusive AD68-02666A Q_MANUAL_GX-20_DUT Exclusive AD68-02667A Q_MANUAL_GX-20_RUS Exclusive AD68-02668A Q_MANUAL_GX-20_CHI_S Exclusive AD68-02669A Q_MANUAL_GX-20_SWE Exclusive AD68-02670A Q_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 229
Common 6801-001675 WARRANTY CARD_TSOE(CHINA)_PRODUCT Common 6801-001663 AS_CENTER_MANUAL_TSEO_S Common 6801-001664 LOCAL_WARRANTY_CARD_INDIA Common 6801-001665 LOCAL_WARRANTY CARD_ITALIA Common 6801-001681 WARRANTY CARD_CANADA Common AD68-02558A PRC_CARD_RUSSIA Common AD81-00883A LI-ION BATTERY_SLB-1674 Exclusive AD81-06277A CHARGER_SBC-L6 Exclusive - This Document can not be used without Samsung's authorization -...
Page 230
. WIRING DIAGRAM - This Document can not be used without Samsung's authorization -...
Page 231
S300-T770 GREEN Q100-Q200 BROWN S300-T770 BROWN Q100-Q200 BLACK T770-T100 BLACK Q100-Q200 T770-T100 WHITE Q104-Q110 BLUE T770-T100 Q200-T770 YELLOW T770-T100 BLACK Q200-T770 VIOLET T770-T100 BLUE Q200-T100 GREEN Q200-T100 PINK Q200-T100 - This Document can not be used without Samsung's authorization -...
Page 232
. FIRMWARE 1. Firmware Basic Version Check 1. Turn on the camera. 2. Turn on the camera while pressing the menu button. 3. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Page 233
Right click the mouse on the "download the program file" button and then select "Save as (A)... ". ✁ 3. Insert a memory card and leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 234
. FIRMWARE 4. Turn on the camera. 5. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Page 235
Check that the name of the firmware file is "FWGX20B.BIN". 2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card for firmware into the camera. - This Document can not be used without Samsung's authorization -...
Page 236
M ENU b utto . 6. If the following indication appears ✁ ✂ on the LCD monitor, select Y ES using the direction keys and press the OK button. - This Document can not be used without Samsung's authorization -...
Page 237
. FIRMWARE The firmware upgrade starts. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. - This Document can not be used without Samsung's authorization -...
Page 238
When the firmware upgrade is completed, the camera is set back to the original factory settings (language, date, time). Readjustments for each item are not needed, as the firmware upgrade is not relevant to the data related to adjustments. - This Document can not be used without Samsung's authorization -...
Page 239
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (firmware for replacing the main board) into the camera. - This Document can not be used without Samsung's authorization -...
Page 240
. FIRMWARE 4. leave the cover open. 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
Page 241
The firmware upgrade starts for replacing the main board. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. Removing the current firmware…. - This Document can not be used without Samsung's authorization -...
Page 242
Writing new firmware…. 8. When the upgrade is completed, the camera's power is turned off automatically. After the firmware upgrade for replacing the main board, run the EEPROM PATCH. - This Document can not be used without Samsung's authorization -...
Page 243
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (two files for EEPROM PATCH) into the camera. 4. leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 244
. FIRMWARE 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
Page 245
After the firmware upgrade for replacing the main board and the execution of the EEPROM PATCH are completed, make sure to carry out adjustments. See “Adjustments” for detailed adjustments. - This Document can not be used without Samsung's authorization -...
Page 246
. ADJUSTMENT 1. Preparation for Adjustments ✁ Preparation Equipment ✂ A djustments program software (written in CD-R) for 77012 (GX-20) ✂ P ersonal Computer (below PC for adjustment) OS : Windows XP SP2 CPU : above 1GHz RAM : above 512MB HD Bin Memory : above 500MB ✂...
Page 247
. ADJUSTMENT 2. Setting the computer and writing an SD card Insert the 77012 (GX-20) CD-R for adjustment into the CD-Rom drive of the computer. ✁ (77010£ P ENTAX K20D) ✂ Copy the 7 7010 folder from the CD-R onto the C drive. (Adjustment software main body) ✄...
Page 248
W hen the V B Run Time Set-up p rogram is not installed, double click on the “setup.exe” file in ✞ ✟ the° v b6run_cs_x.x.x° f older and execute the installation. - This Document can not be used without Samsung's authorization -...
Page 249
LV checker (for checking LV values) ✂ 1. Computer Set-up 2 . Setting the computer in the P reparation section has to be completed. ☎ ✆ ☎ ✆ (Use the digital adjustment software.) - This Document can not be used without Samsung's authorization -...
Page 250
T urn on the camera and check that the camera is recognized by the PC. ✞ ☎ ✆ S et the light box to L V12 ✟ P osition the lens on the top center of the light box. - This Document can not be used without Samsung's authorization -...
Page 251
The digital adjustment screen appears. Click on the icon for calibration at the top left of the screen. ✞ The calibration screen appears. Click on the “Enter” key (or “START” button). ✟ (Release 15 times about for 35 secs.) - This Document can not be used without Samsung's authorization -...
Page 252
E nd the adjustments software by clicking on the [X] button (or [END] button ). ✄ ☎ ✆ S ee the E rror code table i n the manual for NG adjustment. - This Document can not be used without Samsung's authorization -...
Page 253
Shutter speed adjustment according to the histogram ✂ K 20D_PDCAdj ✄ Initial settings Function test (Initialized at the factory) *SR check can be skipped if SR adjustment is completed. ✂ I nitialize Set ✄ - This Document can not be used without Samsung's authorization -...
Page 254
S et the AF change lever to ( top position). ✝ C amera setting: mode dial “M”, OPS switch “ON” ✞ ✟ M ount the OPS unit adjustment plate ( ) on the body. - This Document can not be used without Samsung's authorization -...
Page 255
Double click on the K 20D SR Operation.exe file in the adjustment software folder and execute it. ✂ ✆ ✝ The adjustment screen appears. ✞ Click on the [Start] button. ✟ - This Document can not be used without Samsung's authorization -...
Page 256
✄ ☎ I f the T100 is replaced enter the CCD ID no. twice. ✆ Click on INPUT. ✝ C lick on the “Cancel” button when stopping the adjustment. - This Document can not be used without Samsung's authorization -...
Page 257
Check the “Unconnect” display, and end the adjustment by clicking on the [X] button. ✄ I f the adjustment is displayed as NG, the green turns into red. ✁ - This Document can not be used without Samsung's authorization -...
Page 258
V isual C++Runtime2005 m ust be installed on the PC already. ✆ ✄ ☎ T he 77010 S R_GainForCS f older must be copied onto the hard disk. - This Document can not be used without Samsung's authorization -...
Page 259
Set the lighting to LV 10 to 12 without the surface of the chart spotted. ✄ Set the zoom ring of the D-XENON 50-200mm lens to 200mm and its distance ring to 2m. ☎ (Fix the four sections with tape to prevent vibration.) - This Document can not be used without Samsung's authorization -...
Page 260
✠ C heck C heck again that the distance is 2.0mm. Turn on the controller and turn the dial up to 1,000 rpm. Turn off the controller after checking. - This Document can not be used without Samsung's authorization -...
Page 261
Connect the camera to the PC using the USB cable, and turn it on. ✁ 3. Adjustment Double click on the “SR_GainForCS.exe” file in the 77010 S R_GainForCS folder. ✂ ✄ ☎ Start the adjustment by clicking on the “Execute” button. ✆ - This Document can not be used without Samsung's authorization -...
Page 262
T urn on the controller (1,000 rpm). Adjust the X direction by clicking on the “OK” button. ✂ T urn off the controller, and click on the “OK” button.(The following adjustment starts.) - This Document can not be used without Samsung's authorization -...
Page 263
Turn off the controller, and change the positions of the camera and the stage to the Y direction ✂ adjustment. ✄ IMPORTANT Handle the stage carefully, as it is heavy. Do not touch the black vibration plate. - This Document can not be used without Samsung's authorization -...
Page 264
C lick on [OK], and adjust the Y direction in the same way as the X direction adjustment. ☎ I f all the adjustments are completed, then the OK message appears. ✆ E nd the adjustments by clicking on the [X] button or [Quit] button. - This Document can not be used without Samsung's authorization -...
Page 265
✁ F5.6 set plate for photometric standard lens (No.95901-D20 only) ✁ Side AF gradient adjustment tool (square) ✁ AF gradient adjustment tool (cross) ✁ Hexagonal driver 1.5mm (HD-M1.5) ✁ - This Document can not be used without Samsung's authorization -...
Page 266
✞ ✄ ☎ S et the SR (OIS) lever to O FF ✟ C onnect the camera to the PC using the USB cable and turn on the camera. - This Document can not be used without Samsung's authorization -...
Page 267
D ata initialization C AUTION Select , as the ✆ ✝ ✂ ✄ SR adjustment data is cleared. Replace the main board? Adjustment screen and all the items display - This Document can not be used without Samsung's authorization -...
Page 268
. ADJUSTMENT ✁ [ BV ADJUST] ✁ A djust [CCD POSITION ADJUST] ✁ A djust [AGC LEVEL ADJUST] ✂ P erform this after completing all the adjustments and checking.) - This Document can not be used without Samsung's authorization -...
Page 269
Click on the “Cl” icon, and disconnect the communication with the camera. (USB close) ✆ C heck Check that the USB IO is displayed as U nconnect ✝ ✞ ✄ ☎ Click on the “end” icon, and end the adjustment program. ✟ - This Document can not be used without Samsung's authorization -...
Page 270
C lick on the "Op" icon and start the communication with the camera. Check that the USB IO is displayed as "connected". ✟ M ount the diaphragm set ring on the camera with the aperture open. - This Document can not be used without Samsung's authorization -...
Page 271
If there isn't a tool for the diaphragm set ring, a lens which can set the aperture to 1.4 can be used. Connect the camera to the EV tester. ✁ - This Document can not be used without Samsung's authorization -...
Page 272
C lick on the "2. EXPOSURE ADJUST - BV ADJUST" button. Enter the lens ID no. and click on "Input". ✂ S elect the type of the EV tester. - This Document can not be used without Samsung's authorization -...
Page 273
Set the EV tester to LV6 and click on the "OK" button. After the following message appears, change the set plate to an F5.6 set plate. Click on "OK" and continue with the adjustment. - This Document can not be used without Samsung's authorization -...
Page 274
A message “Set the EV tester to LV15” will appear. Set the EV tester to LV15 and click on the “OK” button. If the adjustment is completed, the following message will appear. Click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 275
. ADJUSTMENT The adjustment value is saved in the camera. Click on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
Page 276
If the shutter speed values change identically to the table above according to the changes of the LV values with the aperture stop of F8, the adjustment has been completed. Otherwise perform the adjustment again. - This Document can not be used without Samsung's authorization -...
Page 277
☎ ✆ The adjustment screen appears. ✝ Click on the "Op" icon and start the communication with the camera. ✞ Check that the USB IO is displayed as "connected". - This Document can not be used without Samsung's authorization -...
Page 278
. ADJUSTMENT ✂ I nstall a cross gradient adjustment tool. Set the focus mode to MF. ✁ C onnect the camera (Cross installation) to the EV tester. - This Document can not be used without Samsung's authorization -...
Page 279
. ADJUSTMENT Click on the "3.AF AND REL ADJ - CCD POSITION ADJ - ADJUSTMENT" button. ✁ Click on the “DumpStart” button on Alpha-CROSS. ✂ - This Document can not be used without Samsung's authorization -...
Page 280
Set the LV value on the EV tester to 12 and click on the “OK” button. If the measurement values are displayed in green, it is normal. (Adjust the position of the AF sensor to make the sizes and shapes of the graphs uniform.) - This Document can not be used without Samsung's authorization -...
Page 281
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). Install the square gradient adjustment tool. ✁ - This Document can not be used without Samsung's authorization -...
Page 282
. ADJUSTMENT Click on the “DumpStart” button on Beta-SQUARE. Set the LV value on the EV tester to 12 and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 283
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). - This Document can not be used without Samsung's authorization -...
Page 284
. ADJUSTMENT ✁ I nstall a standard lens (50M F1.4). Set the distance from the camera mount plane to the AF chart no.1 to 1,954.5mm(=1.9545m) using the tripod. - This Document can not be used without Samsung's authorization -...
Page 285
. ADJUSTMENT Click on the “Start” button in “Focus”. Check the conditions of the camera and chart settings as below and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 286
If the centers of the graphs are moved to the red lines, then click on the “Next” button. If the measurement values are displayed in green, it is normal. - This Document can not be used without Samsung's authorization -...
Page 287
Turn the Allen wrench in the same direction for all three areas. If you turn each area in different directions, the gradient will change. You need to check the gradient or adjust it again. - This Document can not be used without Samsung's authorization -...
Page 288
If there isn't a 35-80 F4-5.6 lens, a bundle lens can be used. Set the items as below if a bundle lens is used for adjustment. Focus MF mode, lens distance 55m, distance ring 0.4m. - This Document can not be used without Samsung's authorization -...
Page 289
Connect the camera to the EV tester. (Install a 35-80 lens or a bundle lens) ✁ Click on the “3. AF AND REL ADJ - CCD POSITION ADJ - POSITION CHECK” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 290
I f the AF sensor is positioned correctly, the following message will appear. Click on the “OK” button. If “NG” appears, then adjust the position of the AF sensor again. - This Document can not be used without Samsung's authorization -...
Page 291
. ADJUSTMENT Close the AF sensor position check screen by clicking on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
Page 292
(similar to sensitivity of film). If the signal is weaker than the standard, it increases the level of the signal up to the standard. 1. Adjustment procedure ✁ I nstall a 50mm F1.4 lens on the camera. (Set the focus mode to MF.) - This Document can not be used without Samsung's authorization -...
Page 293
. ADJUSTMENT Connect the camera to the EV tester. (Install a 50m lens.) ✁ Click on the “3. AF AND REL ADJ - AGC LEVEL ADJUST” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 294
S elect the type of EV tester and adjust the LV values (light value, reference exposure value) in the following order 6, 7, 12 and 15 by clicking on the “AGC Adjust” button. If the adjustments are completed, click on the “Close” button. - This Document can not be used without Samsung's authorization -...
Page 295
Install a Macro 50mm F2.8 lens to the camera. (Set the focus mode to MF, infinitive.) ✁ Connect the camera to the EV tester. (Install a 50m lens.) ✂ - This Document can not be used without Samsung's authorization -...
Page 296
C lick on the "Execute" button and start the adjustment. ✆ I f the adjustment is completed, the "OK" message will appear at the bottom left of the screen. - This Document can not be used without Samsung's authorization -...
Page 297
Click on the [X] button and end the adjustment. ✁ If an adjustment error occurs, the "NG" message and an error code will be displayed. ✂ E rror code table in the manual. ✄ ☎ - This Document can not be used without Samsung's authorization -...
Page 298
The adjustment screen appears. ✝ Click on the “Enter” button after entering the temperature ( ) . ( : Use the mouse pointer to select “Fahrenheit”.) ✞ ✟ ✠ - This Document can not be used without Samsung's authorization -...
Page 299
If this state is maintained, the adjustment starts automatically. IMPORTANT Do not touch the camera or the chart during the adjustment. The adjustment has to be performed again if there is contact, even if it was OK. - This Document can not be used without Samsung's authorization -...
Page 300
A djust the position of the camera and the chart in the same way as the vertical sensor's adjustment. (Up and down direction). ✄ I f the adjustment is completed, then the “OK” message appears. ☎ C lick on the [X] button and end the adjustment. - This Document can not be used without Samsung's authorization -...
Page 301
Turn on the camera and check that the hot plug icon is displayed on the PC. ☎ Double click on the "K20D_PDCAdj01.exe" file in the E XE folder. ✆ ✝ ✞ - This Document can not be used without Samsung's authorization -...
Page 302
C lick on the “Op” icon and start the communication with the camera. Check that the USB IO is displayed as “connected”. ✄ C lick on the “6. BATTERY LEVEL ADJUST” button. - This Document can not be used without Samsung's authorization -...
Page 303
If the adjustment is completed, then click on the “CI” button. ✂ Check that the USO IO is changed to “Unconnect” from “Connect”. Click on the “end” button and end the program. ✄ - This Document can not be used without Samsung's authorization -...
Page 304
A djust the brightness and the color temperature using the color thermometer for photography and the LV checker as below. Light Brightness Color temperature LV12 LV12.00Ev ±0.50 2,856K ±30 LV11 LV11.00Ev ±0.01 - This Document can not be used without Samsung's authorization -...
Page 305
Cover the light box (Brightness measurement equipment (light source A, color temperature 2,850K±10, ✟ brightness LV11.00)) with a light blocking cover and position the lens in the middle of the light box. - This Document can not be used without Samsung's authorization -...
Page 306
C lick on “Yes (Y)” if the lens no. is entered correctly. ✞ H it the "Enter" key (or click on the "START" button) and start the adjustment. (Start the adjustment according to the instructions.) - This Document can not be used without Samsung's authorization -...
Page 307
If all the adjustments are completed, then the “OK” message appears. ✁ Click on the [X] button (or [END] button) and end the adjustment program. ✂ (Adjustment time: approx. 3 mins 30 secs). - This Document can not be used without Samsung's authorization -...
Page 308
I f all the adjustments are completed, then the "OK" message appears. ✠ C lick on the [X] button (or [END] button) and end the adjustment program. (Adjustment time: approx. 70secs). - This Document can not be used without Samsung's authorization -...
Page 309
: standard (initial values) P layback Quick view 5secs, set the view display as histogram ✆ ✝ C ustom Allows release apart from the diaphragm ring A. ✆ ✝ - This Document can not be used without Samsung's authorization -...
Page 310
✁ S et the EV tester to LV9. ✂ S et the shutter speed to Tv 500. ✄ S et the 50M F1.4 lens aperture stop to "open" (F1.4). - This Document can not be used without Samsung's authorization -...
Page 311
The peak has to be in the following range of the histogram when looking at the images on the LCD monitor. If it is displayed as NG, check the settings again, or perform the BV adjustment and digital adjustment (CCD) again. - This Document can not be used without Samsung's authorization -...
Page 312
Measure the differences (mm) on the LCD monitor with a ruler. IMPORTANT This has to be checked in front of the camera. Do not damage (scratch) the LCD screen. - This Document can not be used without Samsung's authorization -...
Page 313
Tv500 (standard). Select a histogram zone (A to D) corresponding to the peak position of Tv4000 from the following ✁ figure. (The example above corresponds to type B.) - This Document can not be used without Samsung's authorization -...
Page 314
(Find the shutter speed from the conversion table for the example above. The histogram zone is B. The difference is +1.5mm to the right. Therefore the shutter speed value is 0.273mS) Conversion table of shutter speed (Apply to GX-10•GX-1S•GX-1L) - This Document can not be used without Samsung's authorization -...
Page 315
Click on the “Op” icon and start the communication with the camera. ✞ Check that the USB IO is displayed as “connected”. Click on the “7. SHUTTER SPEED ADJUST” button. ✟ - This Document can not be used without Samsung's authorization -...
Page 316
. ADJUSTMENT Select ''Shutter Tester for 1/4000 Sec” from “Select”. Ignore the message, and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 317
If it is displayed as NG, enter the default value 0 .25 in the “Input Data” section and end the procedure. ✁ ✂ (To validate the converted data.) If it is NG, check the relevant adjustment items again. - This Document can not be used without Samsung's authorization -...
Page 318
. ADJUSTMENT If the adjustment is completed, the values are saved in the camera. Click on the “Close” button and close the adjustment window. - This Document can not be used without Samsung's authorization -...
Page 319
. ADJUSTMENT Click on the “CI” button. Check that the USB IO has been changed to “Unconnect” from “Connect”. ✁ Click on the “end” button and end the program. ✂ - This Document can not be used without Samsung's authorization -...
Page 320
Remove the super-imposer PCB as shown in the following figure. ✁ C onnect the lead wires to the 0-O170 (SI-LED) as shown in the following figure. IMPORTANT Do not apply pressure on the solder of 0-O170. - This Document can not be used without Samsung's authorization -...
Page 321
Apply DC3.2 V and check if the 11 SI-LEDs are turned on and check the positions. ✁ A djustment 1 Loosen the two screws which ✂ ✄ ☎ hold the 0-O170. … Remove the adhesive (5 areas) for the screws. - This Document can not be used without Samsung's authorization -...
Page 322
A fter the adjustment, apply the screw adhesive to the five areas, and remove the lead wires. ✝ A ttach the mount cover to prevent the SI-LEDs from being affected during the work. - This Document can not be used without Samsung's authorization -...
Page 323
Aim the light from the penlight onto the AE sensor and find a position where the shape of the AE sensor ✂ is shown on the 1st mirror by changing the angle of the penlight. - This Document can not be used without Samsung's authorization -...
Page 324
✄ T ighten the screws and check it again. ☎ A fter the adjustment, apply the adhesive to the two areas of the screws for the AE sensor (0-J100). - This Document can not be used without Samsung's authorization -...
Page 326
3. GX-20 : Fig. 3 …………………………………………………………………………………… 38 4. GX-20 : Fig. 4 …………………………………………………………………………………… 39 PARTS LIST FOR GX-20_CODE ……………………………………………………………… 40 5. PACKING ITEM_GX-20 ………………………………………………………………………… 38 . WIRING DIAGRAM ✄ ………………………………………………………………………………………………… 54 - This Document can not be used without Samsung's authorization -...
Page 327
18. Photometric element position adjustment procedure ……………………………………… 147 . SERVICE INFORMATION ✂ 1. Caution ………………………………………………………………………………………… 149 2. Disassembling Process For Camera Body ………………………………………………… 150 3. Assembling Process For Camera Body ……………………………………………………… 178 - This Document can not be used without Samsung's authorization -...
- Modes : Auto, Program, Shutter Priority AE, Aperture Priority AE, Sensitivity Priority AE, Shutter & Aperture Priority, Manual, Bulb, Flash X-sync, User Mode - Compensation : ±3 EV (1/2 EV step), ±2EV (1/3 EV step) - AE Lock : AEL - This Document can not be used without Samsung's authorization -...
Page 329
2.3fps (Standard Continuous : up to 16 shots) Shake Reduction - Type : Image Sensor Shift - Effective Range : Max. 4EV (depends on lens and shooting conditions) Dust Reduction - Yes - This Document can not be used without Samsung's authorization -...
Page 330
•6M : Super Fine (1)91, Super Fine (2)147, Fine 254, Normal 474 •2M : Super Fine (1)239, Super Fine (2)381, Fine 639, Normal 1060 ✁ T hese fi gures are measured under Samsung's standard conditions and may vary depending on shooting conditions and camera settings. Image Play...
Page 331
- 727g (Body only) , 806g (Memory card & Battery included) Operating Temperature - 0 ~ 40°C Operating Humidity - 5 ~ 85% Software - Application : Samsung Master, Samsung RAW Converter 2.0, Adobe Reader - This Document can not be used without Samsung's authorization -...
1024x768 pixels, 16-bit color display compatible monitor (24-bit color display recommended) Power Mac G4 or later Mac OS 10.2 or later Minimum 256MB RAM For Macintosh 250MB of available hard-disk space USB port CD-ROM drive - This Document can not be used without Samsung's authorization -...
Do not attempt to adjust the ✁ aperture lever or the mirror DC input terminal in the camera body. Failure to follow this instruction may cause the product to malfunction. - This Document can not be used without Samsung's authorization -...
Page 334
Picture Wizard OK Button INFO button Direction button Playback button Card access lamp Card cover lock LCD Monitor OIS (Optical Image Stabilization) lever Focus point selection dial Fn Button - This Document can not be used without Samsung's authorization -...
B attery grip supports the green button ( ) function ✁ while you can still adjust the exposure using the battery grip. Vertical position when using the ✂ battery grip - This Document can not be used without Samsung's authorization -...
2. Insert the battery as shown on the picture. Battery lock lever 3. Close the Battery cover and rotate the battery cover lock lever as shown. - This Document can not be used without Samsung's authorization -...
If the memory card cover is left open, the power will ✆ not turn on. Make sure the memory card is correctly positioned ✆ Lock button before inserting it into the camera. - This Document can not be used without Samsung's authorization -...
After attaching, check that the lens is secure. Also check that the red dots of the lens are on top and the attached portion does not move sideways. - This Document can not be used without Samsung's authorization -...
Page 339
Attaching and removing the lens must be done in a clean place. Please avoid contact with liquid water. If the camera°Øs body or the lens gets wet or dirty, camera malfunction may occur. - This Document can not be used without Samsung's authorization -...
Guides appear on the LCD monitor for 3 seconds when powered on or setting dial mode ( ✂ Y ou can set the specifi c time the guides will appear on the LCD monitor for. Select the desired time from [SETUP MENU] > [Guide Display]. - This Document can not be used without Samsung's authorization -...
Page 341
Shooting mode (Mode dial position) Drive mode/Extended Bracket ✔ ✛ Indicators [Metering type], [Focus Point Information], [White balance], and [Sensitivity] only appear ✌ when a setting other than the default setting is selected. - This Document can not be used without Samsung's authorization -...
Page 342
Press the INFO button in capture mode to display the capture function settings on the LCD monitor. ❉ ✁ ✂ ✄ ☎ ✆ ✁ ✝ ✞ ✟ ✠ ✡ ☛ ☞ ✄ ✂ ☎ ✡ ✟ - This Document can not be used without Samsung's authorization -...
Page 343
11. Colour Tone 26. Lens focal length 12. Saturation 27. Aperture Value 13. Contrast 28. Flash Exposure Value 14. Sharpness 29. Shutter Speed 15. Date and time 30. Exposure Compensation Value - This Document can not be used without Samsung's authorization -...
Page 344
❉ ✁ ✂ ✄ ☎ ✆ ✁ ✝ ✞ ✟ ✠ ✡ ☛ ☞ ✄ ✂ ☎ ✡ ✟ ✌ Y ou can change the information initially displayed by pressing the playback button ( - This Document can not be used without Samsung's authorization -...
Page 345
12. Focus point information 24. Shutter Speed 13. Exposure Compensation Value Indicators 5 (Flash mode) and 15 (Flash compensation Value) only appear when the image was ✁ taken with flash. - This Document can not be used without Samsung's authorization -...
Page 346
Capture quality (Image fi le type) ✄ P layback DPOF settings Indicator for Brightness Histogram and RGB Histogram Histogram (R) Histogram (G) Histogram (B) ✄ ✄ Y Histogram R GB Histogram Histogram (Brightness) - This Document can not be used without Samsung's authorization -...
Page 347
If the lighting conditions are too bright to check the subject by using the LCD, Dark Bright checking the histogram will enable more precise exposure control for the shots. Distribution of brightness - This Document can not be used without Samsung's authorization -...
✶ ✶ ✼ ✶ ✻ ✷ ✸ ✁ ✺ ✻ ✽ ✶ ✸ ✶ ✁ ✶ ✺ ✼ ✂ ✶ ✵ ✶ ✶ ✶ ✷ - This Document can not be used without Samsung's authorization -...
Page 349
In the M mode, the exposure value can be different. In the Sensitivity priority mode / Shutter & Aperture Priority mode, ISO sensitivity will display. 15. OIS (Optical Image Stabilization) indicator 16. AF Frame 17. Focus point - This Document can not be used without Samsung's authorization -...
T he following information appears in the LCD panel on top of the camera. ✶ ✁ ✶ ✂ ✶ ✄ ✶ ✶ ✶ ☎ ✶ ✄ ✽ ✾ ✻ ✼ ✂ ✁ ✹ - This Document can not be used without Samsung's authorization -...
Page 351
7. Displays the ISO sensitivity 8. RAW/RAW+ button in use 9. Battery status 10. Exposure Bar 11. Exposure compensation 12. Flash Exposure Compensation indicator 13. Auto Bracket 14. Shutter speed - This Document can not be used without Samsung's authorization -...
. SPECIFICATION 11. CONNECTION DIAGRAM SD/SDHC/MMC Card Card Reader TV Monitor IBM / MAC Lap top - This Document can not be used without Samsung's authorization -...
You can also edit and save the still images. This software is only compatible with Windows. ✁ U sing Samsung RAW Converter 2.0, you can convert a RAW (*.dng) le into a JPEG or TIFF fi le format. ✂ Y ou should allow 5~10 seconds for running the automatic setup program according to the capability of your computer.
PC and can be edited by an image editing program. 1. Install the Digimax Master by following the instructions shown on your PC monitor. Click Click - This Document can not be used without Samsung's authorization -...
Page 355
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 356
. INSTALLATION Click Click Click Click Click - This Document can not be used without Samsung's authorization -...
Page 357
If you have installed the camera driver, the [Found New Hardware Wizard] may not open. ✁ If the download window of Digimax Master opens after starting Samsung Master, the camera driver ✁ was setup successfully.
The camera may malfunction when it is connected to the PC at the same time as Case 5 another USB cable. In this case, disconnect the other USB cable, and connect only one USB cable to the PC. - This Document can not be used without Samsung's authorization -...
Page 359
When the camera is connected to the USB port located on the front of the ✂ Case 9 computer, the computer may not recognise the camera. Connect the camera to the USB port located on the back of the computer. - This Document can not be used without Samsung's authorization -...
AD81-05847A Mount ring GX-10-A104 A107 AD81-05848A Mount lock button GX-10-A107 A115 AD81-05849A AM Selecting slide plate assy. GX-10-0-A115 A117 AD81-05850A RAW button base GX-10-A117 A141 AD81-03454A Solder stand GX-1S-A141 - This Document can not be used without Samsung's authorization -...
Page 365
GX-10-A213 A214 AD81-05880A SD card seal GX-1S-A214 A217 AD81-05881A SD card cover spring GX-10-A217 A218 AD61-03316A Lining board C A220 AD63-02313A I-LCD cushion A A221 AD63-02313A I-LCD cushion B - This Document can not be used without Samsung's authorization -...
Page 366
SR guide plate GX-10-A272 A273 AD81-05913A Guide plate GX-10-A273 A281 AD63-01753A Connector cover A281-1 AD63-02338A Double-sided Tape 1.2x8.5 A281-2 AD63-02337A Double-sided Tape 1.2x28 A282 AD81-05915A Card cover shaft GX-10-A282 1C3,1D7 - This Document can not be used without Samsung's authorization -...
Page 367
A337 AD81-05939A Photometry switch lever GX-10-A337 A338 AD81-05940A Lever click spring GX-10-A338 A339 AD81-05941A Lever brush GX-10-A339 A340 AD81-05942A O-ring 18x1 GX-10-A340 A341 AD81-05943A Round shape double-sided tape GX-10-A341 - This Document can not be used without Samsung's authorization -...
Page 368
AD63-03345A Battery cover A413 AD81-05973A Battery cover spring GX-10-A413 A415 AD66-00615A Battery cover lock claw 2G6,2G7 A417 AD81-05975A Battery cover click spring GX-10-A417 A418 AD61-03792A Battery cover handle plate - This Document can not be used without Samsung's authorization -...
Page 369
GX-10-M15 AD81-06005A SI holder GX-10-M51 AD81-06006A SI Mirror sheet assy. GX-10-0-M52 AD81-02673A SI cover GX-1S-M53 AD81-01157A SI prism molt GX-1S-M54 AD81-06007A SI spring GX-10-M55 M301 AD81-06008A Eyepiece frame GX-10-M301 - This Document can not be used without Samsung's authorization -...
Page 370
Flash frame shaft B GX-10-Q8 AD81-06037A Pop-up spring GX-10-Q9 AD81-06038A Flash frame shaft GX-10-Q10 AD81-06039A F Case waterproof sheet A GX-10-Q11 AD81-06040A F Case waterproof sheet B GX-10-Q12 AD81-06041A Flash window GX-10-Q20 - This Document can not be used without Samsung's authorization -...
Page 371
T940 AD92-00641A AF/MF select circuit block T970 AD92-00639A SD card circuit block AD81-06064A SD card cover GX-10-U1 AD81-01103A Cover retainer screw F GX-1S-A69 AD81-06066A TB wheel retainer screw GX-10-U4 - This Document can not be used without Samsung's authorization -...
Page 372
PET sheet 4x4 GX-10-U13 AD81-06076A Insulating tape 12x20 GX-10-U14 AD63-03318A F tape 6x10 AD63-03319A PVF tape 3.8x10 (0.08) 4D6,4EI AD63-03320A PVF tape 8x12 AD81-08760A Release SW 3722-002788 USB terminal - This Document can not be used without Samsung's authorization -...
Page 373
Double stick tape 6x8 1G4,1H3 DT22 AD63-03328A Double stick tape 9x50 DT24 AD63-03327A Double stick tape 11x42 DT25 AD63-03326A Double stick tape 17x45.3 DT25 AD63-03326A Double stick tape 17x45.3 - This Document can not be used without Samsung's authorization -...
. EXPLODED VIEW AND PART LIST 5. PACKING ITEM_GX-20 - This Document can not be used without Samsung's authorization -...
Page 375
U_MANUAL_GX-20_ENG Exclusive AD68-01905A U_MANUAL_GX-20_GER Exclusive AD68-01906A U_MANUAL_GX-20_FRA Exclusive AD68-01907A U_MANUAL_GX-20_SPA Exclusive AD68-01908A U_MANUAL_GX-20_ITA Exclusive AD68-01909A U_MANUAL_GX-20_DUT Exclusive AD68-01910A U_MANUAL_GX-20_RUS Exclusive AD68-01911A U_MANUAL_GX-20_CHI_S Exclusive AD68-01912A U_MANUAL_GX-20_SWE Exclusive AD68-01913A U_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 376
Q_MANUAL_GX-20_ENG Exclusive AD68-02662A Q_MANUAL_GX-20_GER Exclusive AD68-02663A Q_MANUAL_GX-20_FRA Exclusive AD68-02664A Q_MANUAL_GX-20_SPA Exclusive AD68-02665A Q_MANUAL_GX-20_ITA Exclusive AD68-02666A Q_MANUAL_GX-20_DUT Exclusive AD68-02667A Q_MANUAL_GX-20_RUS Exclusive AD68-02668A Q_MANUAL_GX-20_CHI_S Exclusive AD68-02669A Q_MANUAL_GX-20_SWE Exclusive AD68-02670A Q_MANUAL_GX-20_DAN Exclusive - This Document can not be used without Samsung's authorization -...
Page 377
Common 6801-001675 WARRANTY CARD_TSOE(CHINA)_PRODUCT Common 6801-001663 AS_CENTER_MANUAL_TSEO_S Common 6801-001664 LOCAL_WARRANTY_CARD_INDIA Common 6801-001665 LOCAL_WARRANTY CARD_ITALIA Common 6801-001681 WARRANTY CARD_CANADA Common AD68-02558A PRC_CARD_RUSSIA Common AD81-00883A LI-ION BATTERY_SLB-1674 Exclusive AD81-06277A CHARGER_SBC-L6 Exclusive - This Document can not be used without Samsung's authorization -...
. WIRING DIAGRAM - This Document can not be used without Samsung's authorization -...
Page 379
S300-T770 GREEN Q100-Q200 BROWN S300-T770 BROWN Q100-Q200 BLACK T770-T100 BLACK Q100-Q200 T770-T100 WHITE Q104-Q110 BLUE T770-T100 Q200-T770 YELLOW T770-T100 BLACK Q200-T770 VIOLET T770-T100 BLUE Q200-T100 GREEN Q200-T100 PINK Q200-T100 - This Document can not be used without Samsung's authorization -...
. FIRMWARE 1. Firmware Basic Version Check 1. Turn on the camera. 2. Turn on the camera while pressing the menu button. 3. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Right click the mouse on the "download the program file" button and then select "Save as (A)... ". ✁ 3. Insert a memory card and leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 382
. FIRMWARE 4. Turn on the camera. 5. Check the firmware version. - This Document can not be used without Samsung's authorization -...
Check that the name of the firmware file is "FWGX20B.BIN". 2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card for firmware into the camera. - This Document can not be used without Samsung's authorization -...
Page 384
M ENU b utto . 6. If the following indication appears ✁ ✂ on the LCD monitor, select Y ES using the direction keys and press the OK button. - This Document can not be used without Samsung's authorization -...
Page 385
. FIRMWARE The firmware upgrade starts. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. - This Document can not be used without Samsung's authorization -...
Page 386
When the firmware upgrade is completed, the camera is set back to the original factory settings (language, date, time). Readjustments for each item are not needed, as the firmware upgrade is not relevant to the data related to adjustments. - This Document can not be used without Samsung's authorization -...
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (firmware for replacing the main board) into the camera. - This Document can not be used without Samsung's authorization -...
Page 388
. FIRMWARE 4. leave the cover open. 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
Page 389
The firmware upgrade starts for replacing the main board. (Updating takes about 60 secs. Updating time depends on the contents of the firmware.) * Never attempt to turn off the power. Removing the current firmware…. - This Document can not be used without Samsung's authorization -...
Page 390
Writing new firmware…. 8. When the upgrade is completed, the camera's power is turned off automatically. After the firmware upgrade for replacing the main board, run the EEPROM PATCH. - This Document can not be used without Samsung's authorization -...
2. Insert a fully charged battery into the camera (AC adapter connection is recommended for safety.). 3. Insert an SD card (two files for EEPROM PATCH) into the camera. 4. leave the cover open. - This Document can not be used without Samsung's authorization -...
Page 392
. FIRMWARE 5. Turn on the camera. 6. The following message will appear on the LCD monitor. - This Document can not be used without Samsung's authorization -...
Page 393
After the firmware upgrade for replacing the main board and the execution of the EEPROM PATCH are completed, make sure to carry out adjustments. See “Adjustments” for detailed adjustments. - This Document can not be used without Samsung's authorization -...
. ADJUSTMENT 1. Preparation for Adjustments ✁ Preparation Equipment ✂ A djustments program software (written in CD-R) for 77012 (GX-20) ✂ P ersonal Computer (below PC for adjustment) OS : Windows XP SP2 CPU : above 1GHz RAM : above 512MB HD Bin Memory : above 500MB ✂...
Page 395
. ADJUSTMENT 2. Setting the computer and writing an SD card Insert the 77012 (GX-20) CD-R for adjustment into the CD-Rom drive of the computer. ✁ (77010£ P ENTAX K20D) ✂ Copy the 7 7010 folder from the CD-R onto the C drive. (Adjustment software main body) ✄...
Page 396
W hen the V B Run Time Set-up p rogram is not installed, double click on the “setup.exe” file in ✞ ✟ the° v b6run_cs_x.x.x° f older and execute the installation. - This Document can not be used without Samsung's authorization -...
LV checker (for checking LV values) ✂ 1. Computer Set-up 2 . Setting the computer in the P reparation section has to be completed. ☎ ✆ ☎ ✆ (Use the digital adjustment software.) - This Document can not be used without Samsung's authorization -...
Page 398
T urn on the camera and check that the camera is recognized by the PC. ✞ ☎ ✆ S et the light box to L V12 ✟ P osition the lens on the top center of the light box. - This Document can not be used without Samsung's authorization -...
Page 399
The digital adjustment screen appears. Click on the icon for calibration at the top left of the screen. ✞ The calibration screen appears. Click on the “Enter” key (or “START” button). ✟ (Release 15 times about for 35 secs.) - This Document can not be used without Samsung's authorization -...
Page 400
E nd the adjustments software by clicking on the [X] button (or [END] button ). ✄ ☎ ✆ S ee the E rror code table i n the manual for NG adjustment. - This Document can not be used without Samsung's authorization -...
Shutter speed adjustment according to the histogram ✂ K 20D_PDCAdj ✄ Initial settings Function test (Initialized at the factory) *SR check can be skipped if SR adjustment is completed. ✂ I nitialize Set ✄ - This Document can not be used without Samsung's authorization -...
S et the AF change lever to ( top position). ✝ C amera setting: mode dial “M”, OPS switch “ON” ✞ ✟ M ount the OPS unit adjustment plate ( ) on the body. - This Document can not be used without Samsung's authorization -...
Page 403
Double click on the K 20D SR Operation.exe file in the adjustment software folder and execute it. ✂ ✆ ✝ The adjustment screen appears. ✞ Click on the [Start] button. ✟ - This Document can not be used without Samsung's authorization -...
Page 404
✄ ☎ I f the T100 is replaced enter the CCD ID no. twice. ✆ Click on INPUT. ✝ C lick on the “Cancel” button when stopping the adjustment. - This Document can not be used without Samsung's authorization -...
Page 405
Check the “Unconnect” display, and end the adjustment by clicking on the [X] button. ✄ I f the adjustment is displayed as NG, the green turns into red. ✁ - This Document can not be used without Samsung's authorization -...
V isual C++Runtime2005 m ust be installed on the PC already. ✆ ✄ ☎ T he 77010 S R_GainForCS f older must be copied onto the hard disk. - This Document can not be used without Samsung's authorization -...
Page 407
Set the lighting to LV 10 to 12 without the surface of the chart spotted. ✄ Set the zoom ring of the D-XENON 50-200mm lens to 200mm and its distance ring to 2m. ☎ (Fix the four sections with tape to prevent vibration.) - This Document can not be used without Samsung's authorization -...
Page 408
✠ C heck C heck again that the distance is 2.0mm. Turn on the controller and turn the dial up to 1,000 rpm. Turn off the controller after checking. - This Document can not be used without Samsung's authorization -...
Page 409
Connect the camera to the PC using the USB cable, and turn it on. ✁ 3. Adjustment Double click on the “SR_GainForCS.exe” file in the 77010 S R_GainForCS folder. ✂ ✄ ☎ Start the adjustment by clicking on the “Execute” button. ✆ - This Document can not be used without Samsung's authorization -...
Page 410
T urn on the controller (1,000 rpm). Adjust the X direction by clicking on the “OK” button. ✂ T urn off the controller, and click on the “OK” button.(The following adjustment starts.) - This Document can not be used without Samsung's authorization -...
Page 411
Turn off the controller, and change the positions of the camera and the stage to the Y direction ✂ adjustment. ✄ IMPORTANT Handle the stage carefully, as it is heavy. Do not touch the black vibration plate. - This Document can not be used without Samsung's authorization -...
Page 412
C lick on [OK], and adjust the Y direction in the same way as the X direction adjustment. ☎ I f all the adjustments are completed, then the OK message appears. ✆ E nd the adjustments by clicking on the [X] button or [Quit] button. - This Document can not be used without Samsung's authorization -...
✁ F5.6 set plate for photometric standard lens (No.95901-D20 only) ✁ Side AF gradient adjustment tool (square) ✁ AF gradient adjustment tool (cross) ✁ Hexagonal driver 1.5mm (HD-M1.5) ✁ - This Document can not be used without Samsung's authorization -...
Page 414
✞ ✄ ☎ S et the SR (OIS) lever to O FF ✟ C onnect the camera to the PC using the USB cable and turn on the camera. - This Document can not be used without Samsung's authorization -...
Page 415
D ata initialization C AUTION Select , as the ✆ ✝ ✂ ✄ SR adjustment data is cleared. Replace the main board? Adjustment screen and all the items display - This Document can not be used without Samsung's authorization -...
Page 416
. ADJUSTMENT ✁ [ BV ADJUST] ✁ A djust [CCD POSITION ADJUST] ✁ A djust [AGC LEVEL ADJUST] ✂ P erform this after completing all the adjustments and checking.) - This Document can not be used without Samsung's authorization -...
Page 417
Click on the “Cl” icon, and disconnect the communication with the camera. (USB close) ✆ C heck Check that the USB IO is displayed as U nconnect ✝ ✞ ✄ ☎ Click on the “end” icon, and end the adjustment program. ✟ - This Document can not be used without Samsung's authorization -...
C lick on the "Op" icon and start the communication with the camera. Check that the USB IO is displayed as "connected". ✟ M ount the diaphragm set ring on the camera with the aperture open. - This Document can not be used without Samsung's authorization -...
Page 419
If there isn't a tool for the diaphragm set ring, a lens which can set the aperture to 1.4 can be used. Connect the camera to the EV tester. ✁ - This Document can not be used without Samsung's authorization -...
Page 420
C lick on the "2. EXPOSURE ADJUST - BV ADJUST" button. Enter the lens ID no. and click on "Input". ✂ S elect the type of the EV tester. - This Document can not be used without Samsung's authorization -...
Page 421
Set the EV tester to LV6 and click on the "OK" button. After the following message appears, change the set plate to an F5.6 set plate. Click on "OK" and continue with the adjustment. - This Document can not be used without Samsung's authorization -...
Page 422
A message “Set the EV tester to LV15” will appear. Set the EV tester to LV15 and click on the “OK” button. If the adjustment is completed, the following message will appear. Click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 423
. ADJUSTMENT The adjustment value is saved in the camera. Click on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
Page 424
If the shutter speed values change identically to the table above according to the changes of the LV values with the aperture stop of F8, the adjustment has been completed. Otherwise perform the adjustment again. - This Document can not be used without Samsung's authorization -...
☎ ✆ The adjustment screen appears. ✝ Click on the "Op" icon and start the communication with the camera. ✞ Check that the USB IO is displayed as "connected". - This Document can not be used without Samsung's authorization -...
Page 426
. ADJUSTMENT ✂ I nstall a cross gradient adjustment tool. Set the focus mode to MF. ✁ C onnect the camera (Cross installation) to the EV tester. - This Document can not be used without Samsung's authorization -...
Page 427
. ADJUSTMENT Click on the "3.AF AND REL ADJ - CCD POSITION ADJ - ADJUSTMENT" button. ✁ Click on the “DumpStart” button on Alpha-CROSS. ✂ - This Document can not be used without Samsung's authorization -...
Page 428
Set the LV value on the EV tester to 12 and click on the “OK” button. If the measurement values are displayed in green, it is normal. (Adjust the position of the AF sensor to make the sizes and shapes of the graphs uniform.) - This Document can not be used without Samsung's authorization -...
Page 429
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). Install the square gradient adjustment tool. ✁ - This Document can not be used without Samsung's authorization -...
Page 430
. ADJUSTMENT Click on the “DumpStart” button on Beta-SQUARE. Set the LV value on the EV tester to 12 and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 431
AF sensor by turning the two areas with an Allen wrench as shown in the following figure. Adjust the gradient until the green appears on the screen. (The values are better to close to “0”.). - This Document can not be used without Samsung's authorization -...
Page 432
. ADJUSTMENT ✁ I nstall a standard lens (50M F1.4). Set the distance from the camera mount plane to the AF chart no.1 to 1,954.5mm(=1.9545m) using the tripod. - This Document can not be used without Samsung's authorization -...
Page 433
. ADJUSTMENT Click on the “Start” button in “Focus”. Check the conditions of the camera and chart settings as below and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 434
If the centers of the graphs are moved to the red lines, then click on the “Next” button. If the measurement values are displayed in green, it is normal. - This Document can not be used without Samsung's authorization -...
Page 435
Turn the Allen wrench in the same direction for all three areas. If you turn each area in different directions, the gradient will change. You need to check the gradient or adjust it again. - This Document can not be used without Samsung's authorization -...
If there isn't a 35-80 F4-5.6 lens, a bundle lens can be used. Set the items as below if a bundle lens is used for adjustment. Focus MF mode, lens distance 55m, distance ring 0.4m. - This Document can not be used without Samsung's authorization -...
Page 437
Connect the camera to the EV tester. (Install a 35-80 lens or a bundle lens) ✁ Click on the “3. AF AND REL ADJ - CCD POSITION ADJ - POSITION CHECK” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 438
I f the AF sensor is positioned correctly, the following message will appear. Click on the “OK” button. If “NG” appears, then adjust the position of the AF sensor again. - This Document can not be used without Samsung's authorization -...
Page 439
. ADJUSTMENT Close the AF sensor position check screen by clicking on the “CLOSE” button. - This Document can not be used without Samsung's authorization -...
(similar to sensitivity of film). If the signal is weaker than the standard, it increases the level of the signal up to the standard. 1. Adjustment procedure ✁ I nstall a 50mm F1.4 lens on the camera. (Set the focus mode to MF.) - This Document can not be used without Samsung's authorization -...
Page 441
. ADJUSTMENT Connect the camera to the EV tester. (Install a 50m lens.) ✁ Click on the “3. AF AND REL ADJ - AGC LEVEL ADJUST” button. ✂ - This Document can not be used without Samsung's authorization -...
Page 442
S elect the type of EV tester and adjust the LV values (light value, reference exposure value) in the following order 6, 7, 12 and 15 by clicking on the “AGC Adjust” button. If the adjustments are completed, click on the “Close” button. - This Document can not be used without Samsung's authorization -...
Install a Macro 50mm F2.8 lens to the camera. (Set the focus mode to MF, infinitive.) ✁ Connect the camera to the EV tester. (Install a 50m lens.) ✂ - This Document can not be used without Samsung's authorization -...
Page 444
C lick on the "Execute" button and start the adjustment. ✆ I f the adjustment is completed, the "OK" message will appear at the bottom left of the screen. - This Document can not be used without Samsung's authorization -...
Page 445
Click on the [X] button and end the adjustment. ✁ If an adjustment error occurs, the "NG" message and an error code will be displayed. ✂ E rror code table in the manual. ✄ ☎ - This Document can not be used without Samsung's authorization -...
The adjustment screen appears. ✝ Click on the “Enter” button after entering the temperature ( ) . ( : Use the mouse pointer to select “Fahrenheit”.) ✞ ✟ ✠ - This Document can not be used without Samsung's authorization -...
Page 447
If this state is maintained, the adjustment starts automatically. IMPORTANT Do not touch the camera or the chart during the adjustment. The adjustment has to be performed again if there is contact, even if it was OK. - This Document can not be used without Samsung's authorization -...
Page 448
A djust the position of the camera and the chart in the same way as the vertical sensor's adjustment. (Up and down direction). ✄ I f the adjustment is completed, then the “OK” message appears. ☎ C lick on the [X] button and end the adjustment. - This Document can not be used without Samsung's authorization -...
Turn on the camera and check that the hot plug icon is displayed on the PC. ☎ Double click on the "K20D_PDCAdj01.exe" file in the E XE folder. ✆ ✝ ✞ - This Document can not be used without Samsung's authorization -...
Page 450
C lick on the “Op” icon and start the communication with the camera. Check that the USB IO is displayed as “connected”. ✄ C lick on the “6. BATTERY LEVEL ADJUST” button. - This Document can not be used without Samsung's authorization -...
Page 451
If the adjustment is completed, then click on the “CI” button. ✂ Check that the USO IO is changed to “Unconnect” from “Connect”. Click on the “end” button and end the program. ✄ - This Document can not be used without Samsung's authorization -...
A djust the brightness and the color temperature using the color thermometer for photography and the LV checker as below. Light Brightness Color temperature LV12 LV12.00Ev ±0.50 2,856K ±30 LV11 LV11.00Ev ±0.01 - This Document can not be used without Samsung's authorization -...
Page 453
Cover the light box (Brightness measurement equipment (light source A, color temperature 2,850K±10, ✟ brightness LV11.00)) with a light blocking cover and position the lens in the middle of the light box. - This Document can not be used without Samsung's authorization -...
Page 454
C lick on “Yes (Y)” if the lens no. is entered correctly. ✞ H it the "Enter" key (or click on the "START" button) and start the adjustment. (Start the adjustment according to the instructions.) - This Document can not be used without Samsung's authorization -...
Page 455
If all the adjustments are completed, then the “OK” message appears. ✁ Click on the [X] button (or [END] button) and end the adjustment program. ✂ (Adjustment time: approx. 3 mins 30 secs). - This Document can not be used without Samsung's authorization -...
I f all the adjustments are completed, then the "OK" message appears. ✠ C lick on the [X] button (or [END] button) and end the adjustment program. (Adjustment time: approx. 70secs). - This Document can not be used without Samsung's authorization -...
: standard (initial values) P layback Quick view 5secs, set the view display as histogram ✆ ✝ C ustom Allows release apart from the diaphragm ring A. ✆ ✝ - This Document can not be used without Samsung's authorization -...
Page 458
✁ S et the EV tester to LV9. ✂ S et the shutter speed to Tv 500. ✄ S et the 50M F1.4 lens aperture stop to "open" (F1.4). - This Document can not be used without Samsung's authorization -...
Page 459
The peak has to be in the following range of the histogram when looking at the images on the LCD monitor. If it is displayed as NG, check the settings again, or perform the BV adjustment and digital adjustment (CCD) again. - This Document can not be used without Samsung's authorization -...
Page 460
Measure the differences (mm) on the LCD monitor with a ruler. IMPORTANT This has to be checked in front of the camera. Do not damage (scratch) the LCD screen. - This Document can not be used without Samsung's authorization -...
Page 461
Tv500 (standard). Select a histogram zone (A to D) corresponding to the peak position of Tv4000 from the following ✁ figure. (The example above corresponds to type B.) - This Document can not be used without Samsung's authorization -...
Page 462
(Find the shutter speed from the conversion table for the example above. The histogram zone is B. The difference is +1.5mm to the right. Therefore the shutter speed value is 0.273mS) Conversion table of shutter speed (Apply to GX-10•GX-1S•GX-1L) - This Document can not be used without Samsung's authorization -...
Page 463
Click on the “Op” icon and start the communication with the camera. ✞ Check that the USB IO is displayed as “connected”. Click on the “7. SHUTTER SPEED ADJUST” button. ✟ - This Document can not be used without Samsung's authorization -...
Page 464
. ADJUSTMENT Select ''Shutter Tester for 1/4000 Sec” from “Select”. Ignore the message, and click on the “OK” button. - This Document can not be used without Samsung's authorization -...
Page 465
If it is displayed as NG, enter the default value 0 .25 in the “Input Data” section and end the procedure. ✁ ✂ (To validate the converted data.) If it is NG, check the relevant adjustment items again. - This Document can not be used without Samsung's authorization -...
Page 466
. ADJUSTMENT If the adjustment is completed, the values are saved in the camera. Click on the “Close” button and close the adjustment window. - This Document can not be used without Samsung's authorization -...
Page 467
. ADJUSTMENT Click on the “CI” button. Check that the USB IO has been changed to “Unconnect” from “Connect”. ✁ Click on the “end” button and end the program. ✂ - This Document can not be used without Samsung's authorization -...
Remove the super-imposer PCB as shown in the following figure. ✁ C onnect the lead wires to the 0-O170 (SI-LED) as shown in the following figure. IMPORTANT Do not apply pressure on the solder of 0-O170. - This Document can not be used without Samsung's authorization -...
Page 469
Apply DC3.2 V and check if the 11 SI-LEDs are turned on and check the positions. ✁ A djustment 1 Loosen the two screws which ✂ ✄ ☎ hold the 0-O170. … Remove the adhesive (5 areas) for the screws. - This Document can not be used without Samsung's authorization -...
Page 470
A fter the adjustment, apply the screw adhesive to the five areas, and remove the lead wires. ✝ A ttach the mount cover to prevent the SI-LEDs from being affected during the work. - This Document can not be used without Samsung's authorization -...
Aim the light from the penlight onto the AE sensor and find a position where the shape of the AE sensor ✂ is shown on the 1st mirror by changing the angle of the penlight. - This Document can not be used without Samsung's authorization -...
Page 472
✄ T ighten the screws and check it again. ☎ A fter the adjustment, apply the adhesive to the two areas of the screws for the AE sensor (0-J100). - This Document can not be used without Samsung's authorization -...
Wearing the band which cuts off the electric current and do the reparing PCB type Where the blocking static electricity mat is on by preventing the defect of parts. CONTACT type Be careful of defect and change by pincette. - This Document can not be used without Samsung's authorization -...
Do not leave screws, steel balls or magnetic cards near the OIS block because there is a strong magnet in the OIS block when the cover is open. ✂ F ive screws ✄ E ight screws ☎ A 401•Battery cover - This Document can not be used without Samsung's authorization -...
Page 475
. SERVICE INFORMATION Caution The OIS block protrudes at the bottom. Don't cause any impact to this area. 2> A301 (Top Cover) Screw•O-ring ✁ Screw…pop up the STROBO. ✂ - This Document can not be used without Samsung's authorization -...
Page 476
. SERVICE INFORMATION ✁ S crew ✂ S crew…flip the rubber. ✄ S crew (inside the battery room) ☎ T wo screws - This Document can not be used without Samsung's authorization -...
Page 477
Discharging the strobe's main condenser. ✁ Lift up the A301 and discharge the electricity, charged in the main condenser, with resistance. (The white lead wire and the brown lead wire on the T750). - This Document can not be used without Samsung's authorization -...
Page 478
. SERVICE INFORMATION ✁ F ive lead wires. ✂ R emove the T51 PCB from the connector (sliding lock). ✄ A 301 ☎ A 27 (waterproof sheet) - This Document can not be used without Samsung's authorization -...
Page 479
Remove the T920 PCB from the connector ✁ (plug type). Set the AF lever to MF. ✂ Two screws ( ✄ ☎ Screw…flip the grip rubber. ✆ Screw ✝ A150 ✞ - This Document can not be used without Samsung's authorization -...
Page 480
: Install the mount cover to prevent damage to the SI-LED•TV dial ✁ A 201…Beware of the terminal section at the end and remove the rear cover by lifting the bottom a little. ✄ T wo screws ☎ M 311 - This Document can not be used without Samsung's authorization -...
Page 481
Remove the PCB from the connector (4ea, plug type) ✆ Caution Don't apply excessive pressure on the PCB of the CCD block as this may affect its performance. Ensure that the PCB is not bent. - This Document can not be used without Samsung's authorization -...
Page 482
Caution Beware that the PCB on the OIS block may be damaged if the main board (T100) is moved too far from the body of camera. - This Document can not be used without Samsung's authorization -...
Page 483
. SERVICE INFORMATION Remove the PCB from the connector (plug type). ✁ T100 ✂ - This Document can not be used without Samsung's authorization -...
Page 484
. SERVICE INFORMATION 5> 0-T970 (SD Circuit Block) ✁ T wo lead wires (red, white) ✂ T hree screws ✄ 0 -T970 - This Document can not be used without Samsung's authorization -...
Page 485
6> 0-T770·0-A51 (PZ Circuit Block·Tripod Holder) Two lead wires (white, brown) ✁ Screw ✂ When removing the 0-T770 and lead wires, be careful of the double sided tape. ✄ Four screws ☎ 0-A51 ✆ - This Document can not be used without Samsung's authorization -...
Page 486
OIS block. ✂ D on't put excessive pressure on the moving parts of the OIS block. ✂ D on't put excessive pressure on the PCB of the OIS block. - This Document can not be used without Samsung's authorization -...
Page 487
. SERVICE INFORMATION 7> O201 (LCD Block) Remove the PCB from the A E-L butto. ✁ ✂ ✄ Screw ☎ A TY screw ✆ - This Document can not be used without Samsung's authorization -...
Page 488
R emove the T700 PCB from the connector (flip lock). ✆ R emove the BT (6 x 15) from the grip area and pull out the four lead wires. - This Document can not be used without Samsung's authorization -...
Page 489
. SERVICE INFORMATION Flip two PCBs to the outside and place the LCD block (O201) back into position. ✁ Remove the soldering from the three lead wires. ✂ O201 ✄ - This Document can not be used without Samsung's authorization -...
Page 490
R emove the soldering from the three lead wires. ✄ R emove the PCB near the release switch and the green button. ☎ S crew ✆ A TY screw ✝ A 350 - This Document can not be used without Samsung's authorization -...
Page 491
9> 0-T700 (Top Right Relay Board) 12 Lead wires (not identical to wiring 76830 G 119 · G 100 · A 105 · E 000) ✁ ✂ ✄ ☎ ✁ ✆ - This Document can not be used without Samsung's authorization -...
Page 492
. SERVICE INFORMATION ✁ F our soldering areas on the T71 PCB. ✂ R emove the PCB from the DT. - This Document can not be used without Samsung's authorization -...
Page 493
. SERVICE INFORMATION Two TY screws ✁ Two screws ✂ T700 ✄ - This Document can not be used without Samsung's authorization -...
Page 494
. SERVICE INFORMATION 10> 0-T750 (Top Left Relay Board) ✁ S even soldering areas on the O170 PCB ✂ F our lead wires ✄ S even lead wires - This Document can not be used without Samsung's authorization -...
Page 495
Two TY screws ✂ Remove the connector from the Q200. ✄ Remove the PCB from the RAW button. ☎ Remove the PCB from the penta area. ✆ T750 ✝ - This Document can not be used without Samsung's authorization -...
Page 496
✁ A TY screw ✂ A 117 ✄ S et the AF switch to the bottom position. ☎ A TY screw ✆ 0 -T940…remove carefully, beware of the switch. - This Document can not be used without Samsung's authorization -...
Page 497
. SERVICE INFORMATION A TY screw ✁ TY-CNL screw ✂ CSM screw ✄ Q200. Related parts ☎ - This Document can not be used without Samsung's authorization -...
Page 498
A423 (mask) ✄ C NL-D ☎ L ift up the T901 PCB. ✆ C NL-D Ä1.7 x 2.5 (Two) ✝ T Y-CSM ✞ T Y-CNL-D Ä1.7 x 4.0 (Three) - This Document can not be used without Samsung's authorization -...
Page 499
. SERVICE INFORMATION 0-A3 ✁ - This Document can not be used without Samsung's authorization -...
Page 500
. SERVICE INFORMATION 13> T901 (Bottom Relay Board) ✁ T wenty soldering areas on the T301·M100 ✂ T 901·two lead wires ✄ S crew ☎ A 141 - This Document can not be used without Samsung's authorization -...
Page 501
. SERVICE INFORMATION 14> A6 (Left Large Plate·Related Parts) CNL-D ✁ TY-CNL-D ✂ Four TY-CSM screws ✄ ☎ - This Document can not be used without Samsung's authorization -...
✁ A 6 … Tidy up the lead wire and the flexible PCB as shown in the figure. ✂ F our TY-CSM1.7x4.0 screws ✄ T Y-CNL-D1.7x4.0 ☎ C NL-D1.7x2.5 - This Document can not be used without Samsung's authorization -...
Page 503
. SERVICE INFORMATION 2> T901 (Bottom relay board) A141 ✁ TY-CNL-1.7x3.5 ✂ T901(Two red and black lead wires) ✄ Solder on the twenty land areas of the T301·100 flexible PCB. ☎ - This Document can not be used without Samsung's authorization -...
Page 504
P ut the O-A3into the body of the camera while tidying up the lead wires and the flexible PCB. ✄ T hree TY-CNL-D1.7x4.0 ☎ T wo CNL-D1.7x2.5 ✆ T Y-CSM1.7x4.0 ✝ C onnect the theT901 flexible PCB to the 0-A3. - This Document can not be used without Samsung's authorization -...
Page 505
. SERVICE INFORMATION A423 (Mask) ✁ ✂ CNL-D1.7x1.6 (2 ✄ ☎ Attach the U12 (8x12) firmly. ✆ Tidy up the two lead wires (red·black, S250). ✝ - This Document can not be used without Samsung's authorization -...
Page 506
✝ T Y-CNL-D1.7x3.5 ✞ S et the AF lever to the middle (AF.S). ✟ 0 -T940 … Install this without damaging to the SW section. ✠ T Y-CNL-D1.7x3.0 - This Document can not be used without Samsung's authorization -...
Page 507
Fix the flexible PCB with the DT (10x5). ✞ Connect the connector of the Q200. ✟ Fix the flexible PCB on the RAW button with ✠ the DT (8x4). - This Document can not be used without Samsung's authorization -...
Page 508
. SERVICE INFORMATION ✁ S older on the seven land areas of the O170 flexible PCB. ✂ F our lead wires ✄ S even lead wires - This Document can not be used without Samsung's authorization -...
Page 509
6> 0-T700 (Top right relay board) T700 … Tidy up as shown in the figure. ✁ ✂ Two CNL-D1.7x1.6 ✄ Two TY-CNL-D1.7x3.5 ☎ Fix the flexible PCB with the DT (10x4). ✆ - This Document can not be used without Samsung's authorization -...
Page 510
. SERVICE INFORMATION ✁ S older on the four land areas of the T71 flexible PCB. ✂ T welve lead wires - This Document can not be used without Samsung's authorization -...
Page 511
Fix the flexible PCBs on the F release SW and the green button SW section with the O207 (DT) and ☎ the DT (5x5). Solder on the three lead wires. ✆ Use the BT (6x15) for the two lead wires (A14 battery armature). ✝ - This Document can not be used without Samsung's authorization -...
Page 512
U se the BT (6x15) for the front four lead wires (T950). ✝ C onnect the O100 flexible PCB to the connector. (Flop lock) ✞ C onnect the T700 flexible PCB to the connector. (Flip lock) - This Document can not be used without Samsung's authorization -...
Page 513
. SERVICE INFORMATION CNL-D1.7x2.5 ✁ Two TY-CNL-D1.7x4.5 ✂ Fix the A E-L flexible PCB with the DT(5x5). ✄ ☎ ✆ - This Document can not be used without Samsung's authorization -...
Page 514
0 -T770 ☎ U 7 screw ✆ U se the DT (6x15) for the lead wires from the 0-T770. ✝ S older on the two lead wires (brown, white). - This Document can not be used without Samsung's authorization -...
Page 515
0-T970 … Tidy up the lead wires as shown in the figure. ✁ Three TY-CNL-D1.7x3.5 ✂ ✂ Solder on the two lead wires (red, white). ✄ Attach the T88. ☎ ✆ Attach the T89. ✝ Attach the U13 (11x20). ✞ - This Document can not be used without Samsung's authorization -...
Page 516
✝ C onnect the flexible PCB to the connector. (Plug type) ✞ C onnect the connector by pushing the T100 onto the camera body. (Plug type) - This Document can not be used without Samsung's authorization -...
Page 517
. SERVICE INFORMATION Three CNL-D1.7x2.5 ✁ ✂ TY-CNL-D1.7x3.5 ✄ - This Document can not be used without Samsung's authorization -...
Page 518
✄ S older on the twenty-one lead wires. ☎ U 8 (3.8x10) ✆ U 3 (BT 6x15) … Three sections ✝ A ttach the T99 onto the land area. - This Document can not be used without Samsung's authorization -...
Page 519
Check if there is twisting, peeling, cracking or damage to each sealing. Ensure that the dial doesn't make contact with the waterproof sheet when turning the front digital dial. Front·Rear digital dial ✁ - This Document can not be used without Samsung's authorization -...
Page 520
. SERVICE INFORMATION ✁ M 311 ✂ A 150 - This Document can not be used without Samsung's authorization -...
Page 521
. SERVICE INFORMATION A201 ✁ - This Document can not be used without Samsung's authorization -...
Page 522
. SERVICE INFORMATION ✁ A 301 ✂ A 401 - This Document can not be used without Samsung's authorization -...
Page 523
A98 (O-ring) … Ensure that the O-ring is installed without a cave-in, crack or damage. ☎ U1(=27370-A115) ✆ A201 … Install the A201 slowly from the bottom. (Be careful of the external ports.) ✝ - This Document can not be used without Samsung's authorization -...
Page 524
✂ C NL-D1.7x3.0 ✄ T Y-CNL-D1.7x5.5 … Attach a rubber grip. ☎ A 172(Two TY 1.7x4.5 screws) ✆ C onnect the T920 flexible PCB to the connector. (Plug type) - This Document can not be used without Samsung's authorization -...
Page 525
* The armature of the main SW must not be deformed. * Apply the G151 onto the main SW land. A27(sheet) … no cave-ins or cracks ✁ A301 ✂ - This Document can not be used without Samsung's authorization -...
Page 526
A 171 (TY 1.7x4.0 screw)·A304 (O-ring) ✝ A 171 … Pop up the strobe. ✞ T Y-CNL-D1.7x7.0 … Attach a rubber. ✟ A 173 ✠ T Y-CNL-D1.7x8.0 Ni (inside the battery room) - This Document can not be used without Samsung's authorization -...
Page 527
. SERVICE INFORMATION 16> A401 (Bottom parts) Check Check the installation of the sealing parts. A401·Battery cover ✁ A174 (Eight 1.7x4.0 screws) ✂ A172 (Five TY 1.7x4.5 screws) ✄ - This Document can not be used without Samsung's authorization -...
Page 528
Any unauthorized use of Manual can be punished under applicable International and/or domestic law. International and/or domestic law. - This Document can not be used without Samsung's authorization - - This Document can not be used without Samsung's authorization -...