Table of Contents
Advertisement
Quick Links
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
▪ If you cannot reach your gas supplier,
call the fi re department.
— Installation and service must be
performed by a qualifi ed installer, service
agency or the gas supplier.
4004802-02
©2016, Miles Industries Ltd.
L
EGEND
Direct Vent Gas Insert
785XN (NG) & 785XP (LPG)
Installation and Owner's Manual
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
G4
L e a v e t h i s m a n u a l
w i t h t h e a p p l i a n c e .
R e t a i n t h i s m a n u a l
f o r f u t u r e r e f e r e n c e .
Please read this manual
BEFORE installing and
operating this appliance.
This manual contains instructions to install the
ENGINE ONLY. A front is also REQUIRED to
complete this installation. A barrier screen is pro-
vided with the front. Refer to the manual sup-
plied with the front for installation.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Ce guide est disponible en français sur demande.
Patent Pending
I N S TA L L E R
C O N S U M E R
Advertisement
Table of Contents
Related Manuals for Valor LEGEND G4 785XN
Summary of Contents for Valor LEGEND G4 785XN
- Page 1 EGEND Patent Pending Direct Vent Gas Insert 785XN (NG) & 785XP (LPG) Installation and Owner’s Manual DANGER I N S TA L L E R L e a v e t h i s m a n u a l HOT GLASS WILL w i t h t h e a p p l i a n c e .
-
Page 2: Table Of Contents
fi tter in the State assumes no responsibility for any consequential of Massachusetts. damage(s). Designed and Manufactured by / for Miles Industries Ltd. 190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com © Copyright Miles Industries Ltd., 2016... -
Page 3: Safety Precautions
Safety Precautions READ and UNDERSTAND all instructions carefully Due to the high temperature, the appliance should be before starting the installation. FAILURE TO FOLLOW LOCATED out of traffi c areas and away from furniture these installation instructions may result in possible fi re and draperies. -
Page 4: Safety And Your Fireplace
Child Safety Precautions and Recommendations, A physical barrier is strongly • recommended if there are young Parts of your Valor Fireplace become • children, or at-risk individuals in the extremely hot while in operation. house. Install an approved after- The glass viewing window •... -
Page 5: Owner's Information
For purchasing a Valor by Miles Industries. Your new EXTREMELY HOT!!! radiant gas heater is a technical appliance that must be installed by a qualifi ed dealer. Each Valor fi replace • READ the SAFETY information on pages is fully tested during the production process for your 3 and 4 of this manual BEFORE operating safety and comfort. -
Page 6: Cleaning Your Fireplace
OWNER’S Owner’s Information INFORMATION Cleaning Your Fireplace To remove the window: 1. Unhook the trim WARNING WARNING WARNING with the barrier DO NOT TOUCH THE GLASS WHILE IT IS HOT! screen. Let the fi replace cool fi rst before cleaning it. 2. -
Page 7: Checking Pilot And Burner Flames
fi replace, damage components, cause overheating resulting in dangerous conditions. Damage caused by incorrect window installa- tion is not covered by the Valor warranty. Checking Pilot and Burner Flames A periodic check of the pilot and burner fl ames should be made. -
Page 8: Using Handset Wall Holder
OWNER’S Owner’s Information INFORMATION The appliance area must always be kept clear and 4. Replace the batteries with 4 AA alkaline batteries. free from combustible materials, gasoline and other 5. Replace the cover and screw in place. fl ammable vapors and liquids. 6. -
Page 9: How To Turn Your Fireplace Off (Including Pilot)
OWNER’S Owner’s Information INFORMATION How to Turn Your Fireplace OFF How to Ensure Your Fireplace Cannot (including pilot) Be Turned ON Inadvertently Familiarize yourself with each of these methods before operating your fi replace. You can use one of the two following methods to ensure that your fi... -
Page 10: Remote Control Operation
OWNER’S Remote Control Operation INFORMATION NOTE: Before using the remote control system for IMPORTANT: BEFORE YOU BEGIN, please note that the fi rst time, the receiver and the handset must be on this system, the settings of time, temperature and synchronized. - Page 11 OWNER’S Remote Control Operation INFORMATION MODES OF OPERATION • Press and hold (small fl ame) button to decrease fl ame height or • Briefl y pressing the SET button to set the appliance at pilot fl ame. changes the mode of operation in •...
- Page 12 OWNER’S Remote Control Operation INFORMATION SETTING THE ON / OFF TEMPERATURES • - Nighttime Setback T E M P Temperature Mode (Appliance SETTING THE “DAYTIME” TEMPERATURE must be in standby mode; pilot ignited) - The room temperature Default Settings: (sun), 23ºC / 74ºF TEMP is measured and compared to the Nighttime Setback temperature.
- Page 13 OWNER’S Remote Control Operation INFORMATION SETTING THE “NIGHTTIME SETBACK” TEMPERA- SETTING PROGRAM TIMERS TURE • You can program two periods of time between 12:00 Default Settings: (moon), “ ” (OFF) am and 11:50 pm in each 24-hour cycle. T E M P •...
- Page 14 OWNER’S Remote Control Operation INFORMATION SETTING P1 OFF TIME SETTING P2 ON TIME • Briefl y press SET to scroll to TIMER mode (sun) while the time fl ashes. • Briefl y press SET button to scroll • Follow the instructions given to set P1 ON time. to TIMER (moon) while the time fl...
-
Page 15: Options
787RGL—Refl ective Glass Liner Set 785XNGK—Conversion Kit to Natural Gas 788FBLV2—Fluted Black Liner Set Hearth Gate 789VRLV2—Valor Red Brick Liner Set Hearth gates such as Cardinal’s VersaGates are Front available at retail stores carrying safety products for 790—Floating Trim Kits (2-1/2”) children. -
Page 16: Lighting Instructions
OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING : If you do not follow these instructions exactly A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To save gas, turn the pilot off when not using the appliance for a prolonged period of time. -
Page 17: Specifi Cations
QUALIFIED Specifi cations INSTALLER Approval & Codes *High Altitude Installations This appliance is certifi ed to ANSI Z21.88-2014 / CSA I nput ratings are shown in BTU per hour and are 2.33-2014 American National Standard / CSA Standard certifi ed without deration for elevations up to 4,500 feet for Vented Gas Fireplace Heaters for use in Canada (1,370 m) above sea level. -
Page 18: Overview
QUALIFIED Overview INSTALLER This appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of non-combustible material. DO NOT install into combustible construction. This appliance is NOT APPROVED for installation with a zero clearance kit. WARNING WARNING Chimney Terminal Cap... -
Page 19: Dimensions
QUALIFIED Dimensions INSTALLER 33” (838 mm) 24” (610 mm) 3” 6’ (1.9 m) Fan power cord (76 mm) Optional fan 3” 3” 15” (76 mm) (76 mm) (381 mm) 15” Trim 4” (381 mm) (sold separately) (102 mm) 10” Gas line approx. 24“ (610 mm) of flex protruding from (254 mm) sheet metal box... -
Page 20: Clearances
QUALIFIED Clearances INSTALLER WARNING WARNING Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the fi replace. Avoid placing candles, paintings, photos, and other items sensitive to heat around the fi replace. Combustible Mantel Clearances Mantel Pro- 1”... -
Page 21: Venting
QUALIFIED Venting INSTALLER Typical Vent Installation See list of approved venting accessories on page 36 of this manual. NOTE: Flexible co-linear vent pipes may only be installed into existing non-combustible solid-fuel burning fi replaces Terminal Cap and chimneys. Vent Location The vent terminal must be located through the roof. -
Page 22: Installation Planning
QUALIFIED Installation Planning INSTALLER Only qualifi ed licensed or trained personnel should install this appliance. Installer—READ THIS FIRST 1. YOU NEED TO KNOW FROM THE 13. Refi t window. HOMEOWNER what accessories (surround, 14. Reinstall the hot glass warning plate if it has been screen, fan/blower, etc.) will be installed with removed. -
Page 23: Installation
QUALIFIED Existing Fireplace Preparation INSTALLER Gas Line Routing Combustible Mantels Plan the routing of the gas line before proceeding. Combustible mantel clearances must conform to those Utilize the existing hole for the gas line of the factory- required for the original solid-fuel fi replace into which built fi... -
Page 24: Remove Window
QUALIFIED Installation INSTALLER Remove Window The window is held in place by a spring-loaded lever on each side. 1. To remove the window, locate the levers on each side of the window towards the top. Using your fi nger, pull the lever towards you and unhook it from the window frame bracket. -
Page 25: Connect Venting
QUALIFIED Installation INSTALLER Connect Venting IMPORTANT: This appliance’s venting system is room sealed and therefore, does not require room air to be used in the combustion process. 1. Rough-in two 3” diameter vent liners into the existing chimney system from the roof. Be careful not to tear or damage the liners in the process. -
Page 26: Connect Gas Supply
QUALIFIED Installation INSTALLER Connect Gas Supply Pressure Test Points The gas supply inlet connection is a 1/2” NPT female. The minimum supply pressure is given in the section Gas shut-off valve supplied on the end of stainless Specifi cations of this manual—page 16. steel fl... - Page 27 QUALIFIED Installation INSTALLER Alternate Inlet Connection Use common elbow and fi ttings (not supplied) to redirect the position of In cases where local codes do not permit the fl ex the fl ex connector. NOTE: the fl ex connector to be used inside the appliance case, connector bend radius must be no reconnect the fl...
-
Page 28: Install Liner Panels
QUALIFIED Installation INSTALLER Remove and re-install burner (if necessary) 2. Place the rear panel against the back of the fi rebox, on the ledge at bottom, behind the burner. The ceramic panels can be installed without removing the burner. However, you can remove the burner for additional space if desired. -
Page 29: Install Driftwood Kit 1101Dwk
QUALIFIED Installation INSTALLER Install Driftwood Kit 1101DWK 2. Place the right log on the right side of the ceramic burner inserting the two pegs of the log in the holes Material required of the burner. The rear end of the log rests on the •... - Page 30 Pebbles Place the pebbles on the platform as shown below. IMPORTANT: Use only the ceramic rocks approved for use with your Valor fi replace. Use of other rocks can damage your fi replace and void the warranty. WARNING CHOKING HAZARD! Ensure that the fi replace area is clear fi...
-
Page 31: Install Decorative Glass Murano 785Xdgm
IMPORTANT: Use only the fi reglass approved for your Valor fi replace or the fi reglass brands Ameri- can Fireglass™ or fi regear. Use of other fi reglass or crushed glass can damage your fi replace and void the warranty. -
Page 32: Install Decorative Glass Set 785Xdgs
The lip on the top surface goes to the front. IMPORTANT: Use only the fi reglass approved for your Valor fi replace or the fi reglass brands Ameri- can Fireglass™ or fi regear. Use of other fi reglass or crushed glass can damage your fi... -
Page 33: Refi T And Check Window
Damage caused by incorrect window installa- tion is not covered by the Valor warranty. 5. If the Hot Glass Warning plate has been removed from the front lower corner of the window, reinstall it by sliding it between the glass and the frame as indicated below. -
Page 34: Synchronize Remote Control
QUALIFIED Installation INSTALLER Synchronize Remote Control 5. With a sharp object, press and hold the receiver’s reset button until you hear one short and one long The receiver and the handset of the remote control beeps. Release the reset button after the second system must be initially synchronized before the fi... -
Page 35: Check Operation
QUALIFIED Installation INSTALLER Check Operation 3. Loosen the air shutter nuts, adjust and re-tighten. Turn the fi replace fl ame up and down using the remote control to confi rm that the full range of inputs is achieved—see the remote control operation instructions on pages 8–14. -
Page 36: Install Side Shrouds
QUALIFIED Installation INSTALLER Install Side Shrouds Door hinge tabs The side shrouds are required to install the front on should face inwards the appliance. They are supplied with the engine. Fit them to the appliance outer case as indicated (2 screws/side). See instructions supplied with the front trim for installation of trim. -
Page 37: Wiring Diagram
QUALIFIED Wiring Diagram INSTALLER Optional Wall Switch Kit 1265WSK Connector Yellow Optional Fan Remote 795CFKV2 Battery Box Control Module 4 AA Batteries GV60 Wiring Diagram... -
Page 38: Approved Venting Components
QUALIFIED Approved Venting Components INSTALLER Approved Direct Vent Suppliers for Valor Models 700, 739 , 780, 785 and RF24DV Venting Parts Code / availability by Manufacturer Venting Parts Description 4DVC 940264 HSDV4658- Standard Co-axial 46DVA-VC 4DT-VC TM-4VT — 4DH-1313 —... -
Page 39: Warranty
The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase. Alternatively, the warranty registration form may be fi lled out online at www.valorfi replaces.com. b) Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation instructions. -
Page 40: Spare Parts
OWNER’S Spare Parts INFORMATION Part Part Code Description Code Description Number Number Exhaust Slide Assembly 4002287 Switch bracket 4002566 Exhaust Slide Gasket 4000176 Injector elbow #850 NG 9730010 Restrictor enclosure 4002330 Injector elbow #300 LPG 9730035 Metal strip 4002329 Auxiliary battery holder 4002249 Restrictor assembly 4002707... - Page 41 INFORMATION Part Code Description Number Liner panels—complete set Ledgestone 786LSLV2 Refl ective Glass 787RGL Ceramic fl uted black 788FBLV2 Valor red brick 789VRLV2 Top panel Ledgestone 4002368 Ceramic black 4002374 Ceramic black 4002374 Valor red brick 4002385 Rear panel Ledgestone 4004267 Refl...
- Page 42 OWNER’S Spare Parts INFORMATION 3–7 57 58 59 21 22 32 – 38a 27a, 27b...
-
Page 43: Miles Industries Ltd
Thank You ... For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed installer. Please fi ll in the information below. The information provided will be used for customer records only. -
Page 44: Miles Industries Ltd
Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...