Modifying A Washing Programme; Automatic Safety Systems - Fagor FET-5310 Instructions For Use Manual

EN 4 / PROGRAMMING YOUR MACHINE
• DETAILS OF THE PROGRAMMES
• Spin
This allows a separate spin and drain.
Important:
In the case of «Rinse only» followed by a spin or «Spin only»,
ensure that you select a suitable spin speed for the type of washing in
the machine.
• DETAILS OF THE OPTIONS
• Anti-creasing
This option washes your laundry more gently, but with an identical washing
performance. The spin speed is slower so that your laundry creases less.
• Extra rinse
«Especially for sensitive and allergic skin»: adds an extra rinse to the
washing cycle.
• Drip Dry
(spin speed «100»)
This function, for very delicate linen, enables you to remove spinning and to
pass directly to the draining of the washing machine.
• Full drum stop
This function enables you to remove the washing from your machine before
the spin phase or to delay this phase with you washing remaining in water
to prevent creasing.
NB: When the machine is stopped
with the tub full of water, the display
A shows alternately:
Then:
— If you want to drain after spinning, use the selector
suitable spin speed for your type of washing.
The programme will end automatically.
— If you just want to drain, turn the selector
•
Reducing the time
Allows for a reduction in the cycle time according to 2 levels that can be
accessed by pressing on the button several times. Level 1, reduces the
average time by 20%. Level 2 reduces the average time by 40% for laundry
that is only lightly soiled.
•
Delayed start
You can delay the start of your programme by 1 to 19 hours so that you can
benefit from cheap rate electricity or to have the cycle finish at a desired
time.
To do this, select the time that must pass before the cycle starts by pressing
3
successively on button (this is done hour by hour) and then press «start/
5
pause» .
NB:
- Even if you forget to press the «start/pause» button
this option, your choice will still be accepted after a few seconds.
- The time remaining before the start of the cycle is counted down hour by
hour from 19 hours to 1 hour.
- At the end of the waiting period, the programme starts and the display
shows the duration of the selected cycle.

• MODIFYING A WASHING PROGRAMME

• During programming:
Anything can be changed before the «start/pause» button
• After the cycle has started:
You can change the type of textile (for example, switch from "COTTON"
to "SYNTHETICS", etc.). In this case, check that the options you previously
selected are still there.
You must confirm your new selection by pressing the «inicio/pausa» button
.
5
The machine may then possibly drain off some of its water.
2 to choose a
2
to "Drip Dry" (position «100»).
5
after selecting
5
is pressed.
• Throughout the cycle:
Depending on your model, the following changes are possible without
pressing the «start/pause» button
— You can change the temperature for the same type of textile.
NB: If the temperature achieved by the washing cycle is higher than your
new selection, heating the water stops immediately and the cycle continues.
— You can alter the spin speed throughout the cycle.
— You can select «drip dry» and «full drum stop».
— You can activate the «extra rinse» option until rinsing starts.
— You can deactivate all the options throughout the cycle provided that their
action has not already finished.
• During delayed start:
Any kind of programme modification is accepted during a delayed start's
waiting period.
— You can alter the length of a delayed start throughout the waiting period
before the cycle effectively starts.
NB:
- During this period, selecting a new time cancels out the previous selection.
The new period selected is accepted based on the last selection made.
- If you want to cancel the delayed start completely during this period,
first display «19h» using button
Then press the button again and briefly press «start/pause»
The cycle will start immediately.
- If you want to reduce the length of time of the delayed start, proceed in the
same way but do not press the «start/pause» button
Your machine is then ready for a new setting.
— You can only activate the «extra rinse» and «anti-creasing» options
during a delayed start's waiting period.
• When the cycle is over:
A
When the screen shows «- 0 -», you can programme a new cycle
without having to reset the selector
For this, all you have to do is turn one of the selectors or press one of
the buttons.
The screen shows the duration of the programme selected.
The machine is then ready to be reprogrammed.

• AUTOMATIC SAFETY SYSTEMS

• Lid opening safety system:
As soon as washing commences, the lid on your machine is locked.
When the cycle is finished or when the machine has stopped with the drum
full of water, the lid unlocks.
If you have programmed a «delayed start», the lid is not locked until the
waiting period is over and the cycle starts.
If you wish to open the lid during the cycle, press button «start/pause»
briefly and wait 1-2 minutes for the safety system to unlock the lid.
5
Important:
Depending on when you wish to open the lid during the cycle,
this time delay may be a little longer because a cooling down period
may also have to be included.
In fact, to avoid your being severely burnt, the lid safety system will
not open during the cycle unless the temperature inside the machine
is below a certain threshold.
• Water safety system:
During operation, constant control of the water prevents any overflows.
• Spin safety system:
Your washing machine is fitted with a safety system that restricts the spin
when poor load distribution is detected.
In this case, your washing may be insufficiently spun. Redistribute your
washing in the drum and programme a new spin.
• Anti-foam system:
You machine can detect when too much foam is being produced during
spinning.
At such times, spinning stops and the machine drains.
The cycle then restarts, adapting the spin rates and possibly adding an
extra rinse.
40
5
.
3
.
5 .
1 to the « » position.
5
.