Related Manuals for Avdel 07552
Summary of Contents for Avdel 07552
- Page 1 I n s t r u c t i o n M a n u a l Pass onto user to read and keep for reference Threaded Insert Power Tool 07552...
- Page 2 AVDEL policy is one of continuous development. Specifications shown in this document may be subject to changes which may be introduced after publication. For the latest information always consult Avdel. S P E C I F I C A T I O N S F O R 0 7 5 5 2 T O O L ■...
-
Page 3: Table Of Contents
O N T E N T S S A F E T Y General Specific to 07552 Tool I N T E N T O F U S E General Tool Dimensions / Selection P U T T I N G I N T O S E R V I C E... -
Page 4: General
RECOMMENDED AND SUPPLIED BY AVDEL. ANY MODIFICATION UNDERTAKEN BY THE CUSTOMER TO THE TOOL/MACHINE, NOSE ASSEMBLIES, ACCESSORIES OR ANY EQUIPMENT SUPPLIED BY AVDEL OR THEIR REPRESENTATIVES, SHALL BE THE CUSTOMER'S ENTIRE RESPONSIBILITY. AVDEL WILL BE PLEASED TO ADVISE UPON ANY PROPOSED MODIFICATION. -
Page 5: Specific To 07552 Tool
In addition to the general safety rules opposite, the following specific safety points must also be observed: THE OPERATING PRESSURE SHALL NOT EXCEED 8 BAR - 120 LBF/IN DO NOT OPERATE THE TOOL WITHOUT FULL NOSE EQUIPMENT IN PLACE. WHEN USING THE TOOL, THE WEARING OF SAFETY GLASSES IS REQUIRED BOTH BY THE OPERATOR AND OTHERS IN THE VICINITY TO PROTECT AGAINST FASTENER PROJECTION, SHOULD A FASTENER BE PLACED ‘IN AIR’. -
Page 6: General
N T E N T O F U S E The pneumatic 07552 type tool is designed to place Avdel threaded inserts at high speed making it ideal for batch or flow-line assembly in a wide variety of applications throughout all industries. - Page 7 7552 TOOL SELECTION NOSE (see drawing opposite for A & B) UNSET COMPLETE INSERT TORQUE CLUTCH PART Nº Ø TOOL PART Nº NAME & SERIES SETTING (lbf ins) A (mm) B (mm) A (in) B (in) NOSE ASSY PART Nº 3 0 - 3 5 0 8 556- 003 80 0 75 56 - 09 91 6...
-
Page 8: Air Supply
U T T I N G I N T O S E R V I C E A I R S U P P L Y All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and automatic oiling/filtering systems on the main air supply. -
Page 9: Clutch Adjustment - Accessories
C L U T C H A D J U S T M E N T Correct clutch setting is necessary to ensure optimum deformation of the insert. If the deformation is insufficient (clutch torque too low) the insert will rotate in the application. If the deformation is excessive (clutch torque too high), thread distortion will occur and extensive wear on the drivescrew may lead to fracture. -
Page 10: Fitting/Servicing/Components
O S E A S S E M B L I E S Nose assemblies are specifically designed for each size and type of insert used with the 07552 type of tooling. If you have purchased a complete tool, it will already be fitted with the correct nose assembly for your insert. - Page 11 Read the nose assemblies servicing instructions opposite carefully. All nose assemblies also include spring 10 part number 07430-08282 and stop 11 part number 07430-08203. NOSE ASSY 07528-07085 07001-00256 07557-08985 07007-00080 07007-00077 07521-08808 07521-08806 07443-08001 07552-09550 07001-00300 07552-07706 07007-00080 07007-00077 07521-08808 07521-08803 07443-08001 07552-09558 07001-00318 07552-07701...
-
Page 12: Regular Servicing
E R V I C I N G T H E T O O L Regular servicing should be carried out and a comprehensive inspection performed annually or every 200000 cycles, whichever is soonest. I M P O R T A N T The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel. -
Page 13: Maintenance
M A I N T E N A N C E Every 200000 cycles the tool should be completely dismantled and components replaced where worn, damaged or when recommended. All ‘O’ rings and seals should be replaced with new ones and lubricated with Moly Lithium grease EP 3753 before assembling. I M P O R T A N T Safety Instructions appear on pages 2 &... - Page 14 CLUTCH ■ Unscrew clutch housing 78 from front of the tool (left hand thread) and pull out bit holder 1 and clutch assembly. ■ Bit holder 1 may be separated from jaw positive 77 by pressing them apart. ■ Cover 70 may be sprung off of clutch housing 78. ■...
- Page 15 REAR GEAR ASSEMBLY ■ Pull off spacer 60. ■ Hold housing 42 and tap out the internal assembly from the front end. ■ Remove two bearings 12 and spacers 17 and 60 from planet gear spindle 15. ■ Push out two planet gear shafts 62 complete with thirty needles 61. ■...
-
Page 18: Fault Diagnosis Table
A U L T D I A G N O S I S F A U L T D I A G N O S I S T A B L E SYMPTOM POSSIBLE CAUSE REMEDY ➝ Worn thrust bearing or thrust washers ➝... - Page 19 Engineered Fastening and Assembly Systems Declaration of Conformity Avdel UK Limited, Mundells, Welwyn Garden City, Herts, AL7 1EZ declare under our sole responsibility that the product type 07552 Serial Nº ..........to which this declaration relates is in conformity with the following standards or other formative documents...
- Page 20 Tel: +82 31 798 6340 Email: info@acument.com.au Email: AvdelDeutschland@acument.com Fax: +82 31 798 6342 Email: info@acumentkorea.com CANADA ITALY Avdel Canada, a Division of Acument Avdel Italia S.r.l. SPAIN Canada Limited Viale Lombardia 51/53 Avdel Spain S.A. 87 Disco Road 20047 Brugherio (MI)
Need help?
Do you have a question about the 07552 and is the answer not in the manual?
Questions and answers