Avdel 07556 Instruction Manual

Avdel 07556 Instruction Manual

Threaded insert power tool

Advertisement

I n s t r u c t i o n M a n u a l
Pass onto user to read and keep for reference
Threaded Insert Power Tool
07556

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 07556 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Avdel 07556

  • Page 1 I n s t r u c t i o n M a n u a l Pass onto user to read and keep for reference Threaded Insert Power Tool 07556...
  • Page 2 AVDEL policy is one of continuous development. Specifications shown in this document may be subject to changes which may be introduced after publication. For the latest information always consult Avdel. S P E C I F I C A T I O N S F O R 0 7 5 5 6 T O O L ■...
  • Page 3: Table Of Contents

    O N T E N T S S A F E T Y General Specific to 07556 Tool I N T E N T O F U S E General Tool Dimensions / Selection P U T T I N G I N T O S E R V I C E...
  • Page 4: General

    RECOMMENDED AND SUPPLIED BY AVDEL. ANY MODIFICATION UNDERTAKEN BY THE CUSTOMER TO THE TOOL/MACHINE, NOSE ASSEMBLIES, ACCESSORIES OR ANY EQUIPMENT SUPPLIED BY AVDEL OR THEIR REPRESENTATIVES, SHALL BE THE CUSTOMER'S ENTIRE RESPONSIBILITY. AVDEL WILL BE PLEASED TO ADVISE UPON ANY PROPOSED MODIFICATION.
  • Page 5: Specific To 07556 Tool

    In addition to the general safety rules opposite, the following specific safety points must also be observed: THE OPERATING PRESSURE SHALL NOT EXCEED 8 BAR - 120 LBF/IN DO NOT OPERATE THE TOOL WITHOUT FULL NOSE EQUIPMENT IN PLACE. WHEN USING THE TOOL, THE WEARING OF SAFETY GLASSES IS REQUIRED BOTH BY THE OPERATOR AND OTHERS IN THE VICINITY TO PROTECT AGAINST FASTENER PROJECTION, SHOULD A FASTENER BE PLACED ‘IN AIR’.
  • Page 6: General

    N T E N T O F U S E The pneumatic 07556 type tool is designed to place Avdel threaded inserts at high speed making it ideal for batch or flow-line assembly in a wide variety of applications throughout all industries.
  • Page 7 5.75 Dimensions shown in bold are millimetres. Other dimensions are in inches. 7556 TOOL SELECTION ( c o n t i n u e d ) NOSE (see drawing above for A & B) UNSET COMPLETE INSERT TORQUE TOOL PART Nº NAME &...
  • Page 8: Air Supply

    U T T I N G I N T O S E R V I C E A I R S U P P L Y All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators and automatic oiling/filtering systems on the main air supply.
  • Page 9: Clutch Adjustment - Accessories

    C L U T C H A J U S T M E N T If you have ordered a complete tool the clutch will be set for the specified insert. When purchased as a spare part the clutch is supplied unset. Correct clutch setting is necessary to ensure optimum deformation of the insert.
  • Page 10: Fitting/Servicing/Components

    O S E A S S E M B L I E S Nose assemblies are specifically designed for each size and type of insert used with the 07556 type of tooling. If you have purchased a complete tool, it will already be fitted with the correct nose assembly for your insert.
  • Page 11 07007-00080 07007-00077 07521-08808 07521-08806 07443-08001 07001-00337 07552-07703 07007-00080 07007-00077 07522-08802 07443-08001 07552-09586 07552-09588 07001-00084 07552-07710 07007-00081 07007-00078 07443-03110 07430-01808 07443-08002 07556-09184 07001-00326 07552-06804 07007-00080 07007-00077 07521-08810 07521-08805 07443-08001 07552-08804 07440-08002 07001-00256 07552-06805 07007-00080 07007-00077 07521-08808 07521-08806 07443-08001 07552-08805 07440-08002 07556-09185...
  • Page 12: Regular Servicing

    E R V I C I N G T H E T O O L Regular servicing should be carried out and a comprehensive inspection performed annually or every 200000 cycles, whichever is soonest. I M P O R T A N T The employer is responsible for ensuring that tool maintenance instructions are given to the appropriate personnel.
  • Page 13 The airline must be disconnected before any servicing or dismantling is attempted, unless specifically instructed not to. It is recommended that any dismantling operation be carried out in clean conditions. Item numbers in bold refer to the General Assembly drawing and parts list (pages 14 and 15). Prior to dismantling the tool it is necessary to remove the nose assembly.
  • Page 14 I M P O R T A N T It is imperative that the reverse control rods are fitted in the correct sequence (see diagram opposite) to ensure correct tool function. When renewing the long push rod, it is necessary to trim the overall length to give a protrusion of 37.85mm (1.49”)/38.1mm (1.5”) of the push rod above the front face of the output square drive spindle of the final gearbox.
  • Page 15 FRONT GEAR ASSEMBLY (previously removed from handle assembly). ■ Hold ring gear 45 and tap out internal asembly from front end. ■ Remove two bearing 25 and spacers 50 and 47 from planet gear spindle 46. ■ Tap out two shafts 28 and thirty needles 27 and remove two planet gears 49 and drive gear 48. ■...
  • Page 18: Fault Diagnosis Table

    A U L T D I A G N O S I S F A U L T D I A G N O S I S T A B L E SYMPTOM POSSIBLE CAUSE REMEDY ➝ Worn thrust bearing or thrust washers ➝...
  • Page 19 Engineered Fastening and Assembly Systems Declaration of Conformity Avdel UK Limited, Mundells, Welwyn Garden City, Herts, AL7 1EZ declare under our sole responsibility that the product type 07556 Serial Nº ..........to which this declaration relates is in conformity with the following standards or other formative documents...
  • Page 20 Tel: +82 31 798 6340 Email: info@acument.com.au Email: AvdelDeutschland@acument.com Fax: +82 31 798 6342 Email: info@acumentkorea.com CANADA ITALY Avdel Canada, a Division of Acument Avdel Italia S.r.l. SPAIN Canada Limited Viale Lombardia 51/53 Avdel Spain S.A. 87 Disco Road 20047 Brugherio (MI)

Table of Contents