IDEAL Project Heat 15 Installation And Servicing page 20

19 DETERMININg ThE FLUE LENgTh aND FLUE paCKs REqUIRED........CONT'D
90º Elbow Kit 60/100 - (Equivalent flue length resistance = 1M)
45º Elbow Kit 60/100 - (Equivalent flue length resistance = 0.6M)
Minimum horizontal Flue Lengths (Centre line of turret to outside of wall terminal)
Telescopic Flue 'B' Pack = 400mm
Horizontal Flue terminal (600mm long) 'B' Pack = 285mm
Wall Thickness
'B' Pack Flue Type 60/100
Horizontal Flue Terminal
(600mm long) B Pack
Telescopic Flue B Pack
Horizontal Flue Terminal
(1000mm long) B Pack
Horizontal Flue Terminal
(1000mm long) B Pack cut 75mm
For Flue lengths between 658 & 708 use a horizontal Flue Terminal (1000mm long) B pack, cut 75mm off the end of the
terminal section of the telescopic flue only.
20 DETERMININg ThE FLUE LENgTh aND FLUE paCKs REqUIRED, CONT'D
FIgURE 1
Note. Maximum permissible
flue length is measured from
centre line of appliance flue
outlet to outside wall face.
FIgURE 2
Shows the flue required when measured from outside edge of turret to the outside face of the wall (to obtain cut length add 44mm)
horizontal Flue Terminal
(600mm long) B pack
Minimum
B pack (standard)
Plus 1 (1m D pack)
Plus 2 (1m D pack)
Plus 3 (1m D pack)
Plus 4 (1m D pack)
Plus 5 (1m D pack)
Plus 6 (1m D pack)
Plus 7 (1m D pack)
Plus 8 (1m D pack)
Plus 9 (1m D pack)
Note; Telescopic flue B Pack or attached "D" pack extensions do not need to be cut between minimum and maximum values shown above (except
where specified). Horizontal Flue Terminal (600mm long) B Pack flue will require cutting on values below maximum values shown in the table above.
20
INSTALLATION
Std Metric Brick 102.5mm wide
Minimum permissible Wall Thickness
Rear Flue
116
231
546
471
Edge of turret
to outside face of wall plus
44mm = ue length
100mm
REAR
Fit
to wall
NOTES
Centre of turret to edge of turret = 100mm
Turret has a ue insertion of 30mm
The compressed outer wall seal has protruding wall to seal mounting lip - 14mm
From centreline of turret to wall. Rear mount 155mm, side (including clearance) 200mm
Minimum & Maximum finished flue lengths obtainable (dimension 'A' +44mm)
Telescopic Flue B pack
Maximum Minimum
171 556 286
1121 1506 1236
2071 2456 2186
3021 3406 3136
3971 4356 4086
4921 5306 5036
5871 6256 5986
6821 7206 6936
7771 8156 7886
8721 9000 8836
Maximum permissible Wall Thickness
side Flue Rear Flue
102.5
186
501
426
A
Minimum clearance 5mm
horizontal Flue
Terminal (1000mm long)
B pack (Telescopic)
Maximum Minimum
484 601
1434 1551
2384 2501
3334 3451
4284 4401
5234 5351
6184 6301
7134 7251
8084 8201
9000 9000
side Flue
501 456
429 384
761 716
686 641
Edge of turret
to outside face of wall plus
44mm = ue length
A
SIDE
Fit
to wall
Flue length measured from outer terminal lip
to end of outer ue
A + 44mm
horizontal Flue Terminal
(1000mm long) B pack
(Telescopic) Cut 75mm
Maximum Minimum Maximum
816 526
1766 1476
2716 2426
3666 3376
4616 4326
5566 5276
6516 6226
7466 7176
8416 8126
9000 9000
Project Heat -
Installation and Servicing
741
1691
2641
3591
4541
5491
6441
7391
8341
9000