IDEAL Logic Combi 30 Installation Manual
  1. Manuals
  2. Brands
  3. IDEAL Manuals
  4. Boiler
  5. LOGIC+ Combi 30
  6. Installation manual

IDEAL Logic Combi 30 Installation Manual

Hide thumbs Also See for Logic Combi 30:
Table of Contents

Advertisement

Quick Links

USER gUiDE
Logic CombI
24 30 35
For Installation Guide see reverse of book
When replacing any part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require.
Do not use reconditioned or copy parts that have not been clearly authorised by Ideal.
For the very latest copy of literature for specification and maintenance practices visit our
website www.idealboilers.com where you can download the relevant information in PDF format.
For alternative languages in our User Guides please visit our website www.idealboilers.com.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Logic Combi 30 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for IDEAL Logic Combi 30

Summary of Contents for IDEAL Logic Combi 30

  • Page 1 Do not use reconditioned or copy parts that have not been clearly authorised by Ideal. For the very latest copy of literature for specification and maintenance practices visit our website www.idealboilers.com where you can download the relevant information in PDF format.

  • Page 2: Table Of Contents

    Benchmark Commissioning Checklist. You can check your installer by calling Gas Safe Register direct on 0800 4085500. Ideal Boilers is a member of the Benchmark scheme and fully supports the aims of the programme. Benchmark has been introduced to improve the standards of installation and commissioning of central heating systems in the UK and to encourage the regular servicing of all central heating systems to ensure safety and efficiency.

  • Page 3: Boiler Operation

    The domestic hot water preheat will operate with the preheat knob (A) set to ‘preheat on’. boiler off Set the mode knob (D) to ‘boiler off’. The boiler mains power supply must be left on to enable frost protection (see Frost Protection). continued..Ideal Logic Combi - User’s...

  • Page 4: Efficient Heating System Operation

    6. Wait for the pressure gauge to reach 1 to 1.5 bar. 7. Once pressure is reached turn valves & back to the closed position. 8. Disconnect the filling loop, replace cap and plug. Note there can be some water spillage at this point. Ideal Logic Combi - User’s...

  • Page 5: Condensate Drain

    (C) to maximum, (Must return to original setting once cold spell is over). Place the heating on continuous and turn the room thermostat down to 15ºC overnight or when unoccupied. (Return to normal after cold spell). Ideal Logic Combi - User’s...

  • Page 6: Points For The Boiler User

    See boiler “Fault Codes” section. If ‘0’ is displayed then Does the boiler operate and contact Ideal Customer Services See boiler “Operation Modes” provide central heating? Helpline if your appliance is and “Fault Codes” section...

  • Page 7: Normal Operation Display Codes

    The boiler is operating in frost protection. foR Any qUeRieS PleASe RinG tHe ideAl ConSUMeR HelPline : 01482 498660 note. boileR ReStARt PRoCedURe - To restart boiler, turn mode knob to “restart” position and immediately turn knob back to required setting.

  • Page 8: Fault Codes

    Code on boileR BCC Activation Fault Restart the appliance - if the boiler fails to operate then please contact Ideal (if under warranty) or alternatively a Gas Safe Registered Engineer if outside of the warranty period. In IE contact a Registered Gas Installer (RGII).

This manual is also suitable for:

Logic combi 24Logic combi 35

Table of Contents

Save PDF