Yamaha QL5 Reference Manual page 198

FUNCTION PARAMETER 1 PARAMETER 2
NO ASSIGN
(TITLE 1)
RECORDER DIRECT PLAY
:
INC RECALL —
DEC RECALL —
DIRECT RECALL SCENE #000–#300
RECALL UNDO —
STORE UNDO —
SCENE
INC —
DEC —
RECALL —
STORE —
SEND MODE MIX/MATRIX —
MIX1–MIX16
MTRX1–MTRX8
MIX ON FADER
SENDS ON
NORMAL/WITH CUE
MATRIX ON FADER
FADER
SENDS ON FADER
SET [+48V]
Ø
SET [ ]
SET [INSERT ON]
SET [DIRECT OUT ON]
SET [PRE SEND]
SET [TO STEREO]
SET BY SEL —
SET [TO MONO]
SET [TO LCR]
SET [GAIN
COMPENSATION]
SET[AUTOMIXER
AUTO/MAN]
SET DEFAULT
— —
VALUE
Explanation
The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
Recall the scene of the next existing number.
Recall the scene of the previous existing number.
Directly recall the scene of the specified number.
Execute RECALL UNDO.
Execute STORE UNDO.
Select the scene of the next existing number.
Select the scene of the previous existing
number.
Recall the currently-selected scene.
Store the current settings.
If INPUT or ST IN is selected, switch output bus
channels (MIX, MATRIX) to be displayed in the
SEND field of the SELECTED CHANNEL VIEW
screen.
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH CUE
option, cue will be enabled if SENDS ON FADER
mode is engaged or if you switch mode during
SENDS ON FADER mode. Also, with the WITH
CUE option, cue for all output channels will be
canceled if SENDS ON FADER mode is
disengaged.
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If SET [PRE SEND] is selected, "SEND ON FADER"
mode is engaged while you are holding down
the [SEL] key.
It goes OFF when the bank is switched.
While holding down this key, press SELECTED
CH or the [TOUCH AND TURN] knob to reset it
to the default value. It goes OFF when the bank
is switched.
198
FUNCTION PARAMETER 1 PARAMETER 2
SET
NOMINAL — —
VALUE
L ON
R ON
C ON
*5)
LFE ON
Ls ON
Rs ON
PANNING L
PANNING R
PANNING Front Center
SURROUND
PANNING Ls
PAN
PANNING Rs *5)
PANNING Back
PANNING Side L
PANNING Side R
PANNING Center
PANNING TOGGLE *5)
LATCH
TALKBACK ON
UNLATCH
SELECTED CH ASSIGN —
TALKBACK
DIRECT ASSIGN *3)
Setup
Explanation
While holding down this key, press a [SEL] key to
set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center  L  Front Center  R
 Side R  Rs  Back, Ls  Side L  (Center).
Switch TALKBACK on/off.
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
The operations performed when this key is
pressed are as follows.
- Toggle assignment of channel selected in list 3)
ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on.
Otherwise, the LED will be off.
Reference Manual