Sharp AL-2020 Service Manual page 141

SW Data
Item
NO. No.
1 Inhibited to use
2
3 G3 send data
accumulation wait time
S
W 4
5
5 Pause time setup
6
7
8
1 ECM
2 CED signal send
3 CSI transmission
4 DIS reception confirmation
in G3 send
S
5 Inhibited to use
W
6 EOL detection timer
6
7 Countermeasure for echo
in reception (CED tone
send interval)
8 Countermeasure for echo
in transmission (After
reception of DIS, hold time
up to signal send is set.)
1 Dial tone ON/OFF
detection time lower limit
(Intermittent detection)
2 Dial tone detection
3 Busy tone detection
4 Dial tone monitoring time
S
5 Dial tone ON/OFF
W
detection time upper limit
7
(Intermittent detection)
6 Max. length of reception
7 Destination display time
when one-touch key is
pressed
8
1 Memory transmission/
direct transmission default
setup
2 Proxy reception
3 Inhibited to use
4 Quick online send
S
W
5 Remote select function
8
6 Number of times of CNG
detection
7
8
1 Print of total
communication time and
total pages
2 Inhibited to use
S
3 Ringing volume pattern
W
number
4
9
5
6
7
8
Switch selection and contents of functions
Bit No. 3 4
6sec 0 0
5sec 0 1
4sec 1 0
3sec 1 1
Binary input
Bit No. 5 6 7 8
Set range 1 to 15sec
1: Yes 0: No
1: Yes 0: No
1: Yes 0: No
1: 2 times 0: Once in NFS reception,
2 time in DIS reception
1: 25sec 0: 13sec
1: 500ms 0: 75ms
1: 800ms 0: 500ms
1: 300ms 0: 100ms
1: Yes 0: No
1: Yes 0: No
1: 10sec 0: 5sec
1: 400ms 0: 700ms
1: No limit 0: 1.5m
Bit No. 7 8
2sec 0 0
4sec 0 1
6sec 1 0
1: Direct transmission 0: Memory transmission
1: Yes 0: No
1: Yes 0: No
1: Yes 0: No
Binary input
Bit No. 6 7 8
Set range 1 to 4 times
1: Yes 0: No
Binary input
Bit No. 3 4 5 6 7 8
Set range Pattern No. 1 to 35
AL-2020/2035/2040/2050/2060 FAX SOFT SWITCH 12 - 3
Initial value Remark
0
0
0
6sec
0
0 When a value outside
the set range is set,
0
2sec
the initial value is set.
1
0
Yes 1
Yes 1
Yes 1
Once in NFS
reception, 2 time 0
in DIS reception
0
13sec 0
500ms 1
500ms 0
100ms 0
No 0
Yes 1
5sec 0
700ms 0
1.5m 0
When a value outside
0
the set range is set,
2sec
the initial value is set.
0
Memory
0
transmission
Yes 1
0
Yes 1
Refer to User program
"REMOTE
Yes 1
RECEPTION
SELECT".
0 When a value outside
the set range is set,
3 times 1
the initial value is set.
1
Yes 1
0
0 When a value outside
the set range is set,
0
the initial value is set.
0
1
0
0
1