Sharp AL-2020 Service Manual page 131

Main Sub
code code
E7 11 Content Shading trouble (White correction)
Detail The CCD white scan level is abnormal when
the shading.
Cause Improper connection of the CCD unit flat
cable
Dirt on the mirror, the lens, and the reference
white plate
Copy lamp lighting abnormality
CCD unit abnormality
MCU PWB abnormality
(When occurred in the SPF/RSPF scan
position.)
Improper installation of the mirror unit
Check Clean the mirror, lens, and the reference
and white plate.
remedy Check the light quantity and lighting status of
the copy lamp (SIM 05-03).
Check the MCU PWB.
16 Content Abnormal laser output
Detail When the laser output is stopped, HSYNC is
detected.
Cause Laser abnormality
MCU PWB abnormality.
Check Check the laser emitting diode operation.
and Replace the MCU PWB.
remedy
F5 02 Content Copy lamp lighting abnormality
Detail The copy lamp does not turn on.
Cause Copy lamp abnormality
Copy lamp harness abnormality
CCD PWB harness abnormality.
Check Use SIM 5-3 to check the copy lamp
and operations.
remedy When the copy lamp lights up.
Check the harness and the connector
between the CCD unit and the MCU PWB.
When the copy lamp does not light up.
Check the harness and the connector
between the copy lamp unit and the MCU
PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
F6 10 Content FAX board trouble (AL-2060 only)
Detail Communication trouble between MCU and
FAX control PWB
Cause FAX control PWB connector disconnection
Defective harness between FAX control
PWB and MCU PWB
Mother board connector pin breakage
FAX control PWB ROM error/Data error
IC on FAX PWB causes abnormality
Check Check connector/harness of FAX control
and PWB and MCU PWB.
remedy Check the grounding of the copier.
Check FAX control PWB ROM.
Replace the FAX PWB.
H2 00 Content Thermistor open
Detail The thermistor is open.
The fusing unit is not installed.
Cause Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection
The fusing unit is not installed.
Check Check the harness and the connector
and between the thermistor and the PWB.
remedy Use SIM 14 to clear the self diagnostic
display.
Details of trouble
AL-2020/2035/2040/2050/2060 SIMULATION, TROUBLE CODES 10 - 41
Main Sub
code code
H3 00 Content Heat roller high temperature detection
Detail The fusing temperature exceeds 240°C.
Cause Thermistor abnormality
Control PWB abnormality
Fusing section connector disconnection.
Check Use SIM 5-02 to check the heater lamp
and blinking operation.
remedy When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the
control PWB.
When the lamp keeps ON.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic
display.
H4 00 Content Heat roller low temperature detection
Detail 1) When the target temperature (165°C) is
not reached in 55 sec after starting
warming-up.
2) When the temperature below 100°C is
detected for 300ms under the ready print
state.
∗ "Starting warming-up" means not only that
in power supply but also reset that in reset
from shut-off and in side door close. (The
timing of generating H4 is not limited to
that in power supply.)
Cause Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check Use SIM 5-02 to check the heater lamp
and blinking operation.
remedy When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the
control PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp
and the thermostat. Check the interlock
switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic
display.
Details of trouble