Sharp AL-2020 Service Manual page 108

Main Sub
Contents
code code
46 01 Copy density adjustment
(300dpi)
02 Copy density adjustment
(600dpi)
[Function]
Copy density is set for each mode.
When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased,
the copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 cop-
ies become lighter, too.
Press [Exposure mode selector] key (or [
mode. The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1
– 99)
The setting procedure of the magnification ratio is the same as that to copy operation.
Mode
AE mode (300dpi)
TEXT mode (300dpi)
PHOTO mode
TS mode (TEXT)
(300dpi)
TS mode (AE) (300dpi)
[Operation]
AL-2050/2060
1) Initial display
46-01 EXP.LEVEL 300
AE 100% 50( 1-99)
2) [ ] key: Mode selection
46-01 EXP.LEVEL 300
TSAE 100% 50( 1-99)
2) [ ] key: Mode selection
46-01 EXP.LEVEL 300
TEXT 100% 50( 1-99)
3) [Numeric] key: Value entry
46-01 EXP.LEVEL 300
AE 100% 62( 1-99)
4) [START] key: Fixing and printing value
(No change on the LCD)
* Print is started in the set mode.
46-01 EXP.LEVEL 300
AE 100% 62( 1-99)
[Function]
Copy density is set for each mode.
When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).
Change the set value and press [START] key to make a copy under the set value.
When the set value is increased, the copy becomes darker. When the set value is decreased,
the copy becomes lighter.
In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,
Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 cop-
ies become lighter, too.
Press [Exposure mode selector] key (or [
mode. The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1
– 99)
Mode
AE mode (600dpi)
TEXT mode (600dpi)
PHOTO mode
TS mode (TEXT)
(600dpi)
TS mode (AE) (600dpi)
[Operation]
The operation is similar to simulation 46-01.
AL-2020/2035/2040/2050/2060 SIMULATION, TROUBLE CODES 10 - 18
Details of function/operation
] [ ] key for the AL-2050/2060) to switch the
Display item LED
(AL-2050/2060) (AL-2050/2060)
AE COPY mode lamp AE mode lamp
TEXT PRINT mode lamp TEXT mode lamp
PHOTO SCAN mode lamp PHOTO mode lamp
TSTXT PRINT mode lamp
SCAN mode lamp
TSAE COPY mode lamp
SCAN mode lamp
4) To fix the set value without printing, press
[OK] key.
46-01 EXP.LEVEL 300
AE
* To cancel manual feed paper empty MSG,
press any key.
* When performing the AE mode exposure
adjustment, place the test chart on the docu-
ment table so that the center area of 10cm is
not covered.
AL-2020/2035/2040
1) Press [Exposure mode selector] key to
change the mode.
2) Press [ ] [ ] key to set the value.
3) [START] Fixing and printing value
* Print is started in the set mode.
] [ ] key for the AL-2050/2060) to switch the
Display item LED
(AL-2050/2060) (AL-2050/2060)
AE COPY mode lamp AE mode lamp
TEXT PRINT mode lamp TEXT mode lamp
PHOTO SCAN mode lamp PHOTO mode lamp
TSTXT PRINT mode lamp
SCAN mode lamp
TSAE COPY mode lamp
SCAN mode lamp
Display lamp
Default
(AL-2020/2035/2040)
TEXT mode lamp
PHOTO mode lamp
AE mode lamp
PHOTO mode lamp
100% 62( 1-99)
Display lamp
Default
(AL-2020/2035/2040)
TEXT mode lamp
PHOTO mode lamp
AE mode lamp
PHOTO mode lamp
50
50
50
50
50
50
50
50
50
50