Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
I n s t r u c t i o n M
I n s t r u c t i o n M a n u
I n s t r u c t i o n M a n u a l
n s t
n s t r u c t i o n M a n u a l l
r u
u c t i o n M a n u a l
c t i o n M a n
g
We wish you many enjoyable flights with your plane and one again thank you for your choosing a Phoenix Model products.
i o n M a n u
Wingspan : 1500mm (59.2 inch)
Length
: 1250mm (49.2 inch)
Weight
: 2400gr - 2600gr
Engine
: 40 - 46 two stroke / 52 four stroke
Radio
: 4 channel / 4 servos standard
u a
HOBBIRAN.COM
Advertisement
Table of Contents
Related Manuals for Phoenix Model Tiger 3
Summary of Contents for Phoenix Model Tiger 3
- Page 1 Engine : 40 - 46 two stroke / 52 four stroke Radio : 4 channel / 4 servos standard We wish you many enjoyable flights with your plane and one again thank you for your choosing a Phoenix Model products.
-
Page 2: Kit Contents
Instruction Manual tiger KIT CONTENTS: We have organized the parts as they come out of the box for better identification during assembly. We recommend that you regroup the parts in the same manner. This will ensure you have all of parts required before you begin assembly KIT CONTENTS AIR FRAME ASSEMBLIES elevator control system... -
Page 3: Joining The Wing Halves
Instruction Manual tiger 1. Joining the wing halves. Center line Draw a center line. Remove the covering. HOBBIRAN.COM Glue the wing joiner to the wing, using the epoxy glue. Apply the epoxy into the wing section. Glue the wing by epoxy. Apply the trim tape to the center section on the top and the bottom of the wing where they join. - Page 4 Instruction Manual tiger Mark the shape of the servo box to the wing. Remove the covering. Servo box Hard wood Glue the servo box by C.A glue. Install and secure the aileron servo. Clevis Nylon control horn Metal pushrod HOBBIRAN.COM Install the two nylon control horn.
- Page 5 Instruction Manual tiger Nylon clasp Bend "L" the aileron pushrod. Attach the nylon clasp to the aileron servo arm. 3. Installing the landing gear and nose gear. The landing gear. Remove the covering from the bottom of the wing. Collar Gear Drill four holes for the nylon straps.
- Page 6 Instruction Manual tiger The nose gear. Install the wheel. Install the nose gear. 4. Installing the horizontal and vertical stabilizer. Draw a center line. Remove the covering from the fuselage. Attach the horizontal to the fuselage and check it. Mark the shape of the fuselage onto the bottom of the horizontal.
- Page 7 Instruction Manual tiger Remove the covering from the bottom of the horizontal. Glue the horizontal and fuselage by epoxy. Cut away the covering from the fuselage. Mark the shape of the fuselage onto the both side of the vertical. Remove the covering from the vertical. Remove the covering on the top of the fuselage.
- Page 8 Instruction Manual tiger 5. Installing the elevator and rudder pushrod. Control horn The control horn. Install the control horn onto the elevator. Clevis Remove the covering from the slot. Attach the clevis to the elevator pushrod. Control horn Attach the clevis to the control horn. Install the nylon control horn.
- Page 9 Instruction Manual tiger Attach the clevis to the control horn. Install the rudder servo. HOBBIRAN.COM Install the metal connector. Connect the rudder pushrod and the nose gear pushrod to the rudder servo. Cut away the rudder pushrod. Bend "L" the rudder pushrod. Attach the nylon clasp to the servo arm.
-
Page 10: Installing The Fuel Tank
Instruction Manual tiger Cut away the elevator pushrod. Bend "L" the elevator pushrod and attach the nylon clasp. 6. Installing the fuel tank. The stopper. Install the stopper to the tank. Secure the stopper. Install the silicone tube to the tank. C.A glue Wood Slide the fuel tank into the fuselage. - Page 11 Instruction Manual tiger 7. Installing the engine and fuselage servo. Attach the throttle rod to the arm of the carburator. Install the engine and secure it. Install the muffler and secure it. Install the throttle servo. Wire pushrod Wire pushrod Install the metal connector.
-
Page 12: Installing The Spinner And Propeller
Instruction Manual tiger Switch Battery Receiver Install the radio. 9. Installing the spinner and propeller. Install the plate of the spinner. Install the propeller. Install the spinner. -
Page 13: Control Throws
CONTROL THROWS BALANCING 1. We highly recommend setting up a plane using the 1. It is critical that your airplane be balanced correctly. control throws listed. Improper balance will cause your plane to lose control and crash. 2. The control throws should be measured at the widest point of each control surface. - Page 14 I/C FLIGHT WARNINGS HOBBIRAN.COM Always operate in open areas, away Keep all onlookers (especially small from factories, hospitals, schools, THE PROPELLER IS DANGEROUS children and animals) well back from buildings and houses etc. NEVER fly Keep fingers, clothing (ties, shirt the area of operation.
- Page 15 I/C FLIGHT GUIDELINES Operate the control sticks on the When ready to fly, first extend the transmitter and check that the control transmitter aerial. surfaces move freely and in the ALWAYS land the model INTO the CORRECT directions. wind, this ensures that the model lands at the slowest possible speed.