Roland XC-540 User Manual page 141

[PINCHROLL ERROR LOWER PINCHROLL]
was pressed without first lowering the pinch
rollers.
Press any key to clear the error. Pull back the loading lever,
then press .
The pinch rollers were raised while
minated.
The error is cleared automatically after a short wait. Never
move the loading lever while printing is in progress.
[SERVICE CALL xxxx]
An unrecoverable error occurred, or part replace-
ment that must be performed by a service techni-
cian is required.
Note the number displayed, then switch off the sub power.
After you switch off the power, inform your authorized
Roland DG Corp. dealer of the number that appeared on
the display.
[SHEET TOO SMALL CONTINUE?]
The size of the data is larger than the printing or
cutting area of the loaded media.
To continue performing output without correcting this, press
. At this time, the portion extending beyond the
printing or cutting area is not output. To stop output, stop
sending data from the computer, then hold down
for one second or longer. Make the printing or cutting area
wider, such as by replacing the media with a larger piece of
media or by changing the positions of the pinch rollers,
then send the data again.
[SHEET SET ERROR SET AGAIN]
was pressed even though no media is loaded.
Press any key to clear the error. Load media and pull back
the loading lever, then press
[EDGE DETECTION] is set to "ENABLE," but trans-
parent media was loaded.
Raise the loading lever, set the [EDGE DETECTION] menu
item to "DISABLE," then reload the media.
P. 86, "Using Transparent Media"
The loaded media is too small.
Press any key to clear the error. Replace with media of us-
able size.
[TEMPERATURE IS TOO HIGH **°C]
The temperature of the location where the machine
is installed has risen above the ambient tempera-
ture at which the machine can operate.
was illu-
.
7-8 If a Error Message Appears
Operation cannot be continued. Switch off the sub power.
The displayed temperature is the current ambient tempera-
ture of the installation location. Bring the installed location
to a temperature at which operation is possible (15 to 32°C)
and allow the machine to come to room temperature, then
turn on the power.
[TEMPERATURE IS TOO LOW **°C]
The temperature of the location where the machine
is installed has fallen below the ambient tempera-
ture at which the machine can operate.
Operation cannot be continued. Switch off the sub power.
The displayed temperature is the current ambient tempera-
ture of the installation location. Bring the installed location
to a temperature at which operation is possible (15 to 32°C)
and allow the machine to come to room temperature, then
turn on the power.
[AVOIDING DRY-UP TURN OFF POWER]
The print heads were forced to standby position to
prevent them from drying out.
Operation cannot be continued. Switch the sub power off,
then back on. Opening the front cover while printing is in
progress causes an emergency stop. Never allow the print
heads to remain in this state.
[MOTOR ERROR TURN POWER OFF]
A motor error occurred.
Operation cannot be continued. Switch off the sub power.
Next, eliminate the cause of the error, then immediately
switch on the sub power. If the machine is allowed to stand
with the error uncorrected, the print heads may dry out and
become damaged.
This error may be caused by such factors as a mistake in
loading the media, a media jam, or an operation that pulls
the media with excessive force.
The media has jammed.
Carefully remove the jammed media. The print heads may
also be damaged. Perform head cleaning, then perform a
printing test and check the results.
The media was pulled with excessive force.
Excessive tension was applied to the media, and additional
action is necessary to recover from this state. First, move
the loading lever to the rear and adjust the media to create
a small amount of slack, then switch on the sub power.
[WRONG CARTRIDGE]
A cartridge that cannot be used was installed.
Remove the cartridge to clear the error. Use a cartridge of
the specified type.
Chapter 7 What to Do If 139