Hobby ONTOUR Series Operation Manual
  1. Manuals
  2. Brands
  3. Hobby Manuals
  4. Motorhomes
  5. ONTOUR Series
  6. Operation manual

Hobby ONTOUR Series Operation Manual

Caravan
Hide thumbs
Table of Contents

Advertisement

Quick Links

ONTOUR • DE LUXE • DE LUXE EDITION • EXCELLENT • PRESTIGE • PREMIUM • LANDHAUS
OPERATION GUIDE
GB
Version 8 / 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ONTOUR Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hobby ONTOUR Series

Summary of Contents for Hobby ONTOUR Series

  • Page 1 ONTOUR • DE LUXE • DE LUXE EDITION • EXCELLENT • PRESTIGE • PREMIUM • LANDHAUS OPERATION GUIDE Version 8 / 2015...
  • Page 2 1. Introduction Dear Caravaner, Congratulations on the purchase of your new HOBBY Caravan. The trust you have placed in us is both an incentive and an obligation to continuously implement new ideas, technical innovations and fine touches to make our caravans even better. Our fully fitted and highly sophisticated models enable us to offer you the perfect setting for the most enjoyable days of the year.

  • Page 3: Table Of Contents

    1. Introduction Table of Contents Introduction General information .........................1 Markings in these operation instructions ..................2 Safety Intended use ............................4 General information .........................4 Fire protection ..........................4 Emergency equipment ........................6 Before the journey ...........................7 2.5.1 What to observe before your first drive ...................7 2.5.2 Before each drive ..........................9 While driving ..........................10 After the drive ..........................12...
  • Page 4 1. Introduction Contact plan for the light control system ..................76 Special Lighting ..........................77 Water General information ........................78 Water supply ..........................79 Water flushing toilet ........................83 Gas system General safety rules for the use of liquid gas facilities ..............85 Gas supply ............................87 Gas socket, external........................89 10 Built-in devices 10.1...

  • Page 5: General Information

    These operating instructions also describe equipment which may vary from the standard scope of delivery. Therefore, HOBBY shall not be liable for any claims arising from the contents of this handbook. Please understand that we cannot describe all of the individual variations. Your dealer will be pleased to answer any special questions regarding the equipment and tech- nology of your caravan.

  • Page 6: Markings In These Operation Instructions

    1. Introduction 1.2 Markings in these operation instructions The handbook explains the caravan as follows Texts and illustrations The texts which accompany illustrations are found directly to the right of the illustrations. Details in illustrations (here: entry door) are marked with position numbers Lists - Lists are based on key points and are preceded by a dash.
  • Page 7 1. Introduction Optional Extras You have selected a caravan that is equipped to taste. This user manual describes all of the models and equipment offered within the same programme. Therefore, it may include equipment that you have not selected. Differences and, thus, all of the optional extras are marked with an asterisk.

  • Page 8: Safety

    2. Safety 2.1 Intended use This camper has been designed as a mobile travel accommodation for private, not commercial use. It is not intended for permanent re- sidence. Furthermore, no more than the number of people for which this camper has been planned may spend the night in the vehicle. When the camper is on the road, it may only be used in accordance with road traffic regulations and national vehicle safety standards.

  • Page 9: Smoke Detector

    2. Safety • Place a fire cover near the gas cooker. • Keep all escape routes clear. • Ensure that everyone is familiar with the fire prevention measures on site. Fighting a fire • Evacuate all passengers immediately. • Close the main shut-off valve on the gas bottle as well as the shut-off valves on gaspowered appliances.

  • Page 10: Emergency Equipment

    2. Safety 2.4 Emergency equipment To be prepared in case of an emergency, you should always carry the three emergency devices on board and familiarize yourself with them. First-aid kit The first aid kit should always be kept handy. It should have a fixed place in the base vehicle/camper.

  • Page 11: Before The Journey

    Any changes made to the camper that fall under nati- onal traffic regulations must be approved and entered in the registration document! If you have any further questions or difficulties, your authorised Hobby dealer will always be available to assist you!
  • Page 12 2. Safety Fit for a Speed of 60 mph 1. Your HOBBY caravan is technically equipped for a maximum speed of 60 mph. Under no circumstances may this speed be exceeded! 2. Note the permissible maximum speeds for trailer carriages in the country in which you are travelling! 3.

  • Page 13: Before Each Drive

    2. Safety 2.5.2 Before each drive Road safety • Before driving, check that the signalling and lighting systems and brakes function correctly. • If the vehicle has been standing for a longer period of time (approx. 10 months) have an authorised workshop check the brake system and the accelerator system.

  • Page 14: While Driving

    2. Safety Interior You must also prepare the interior of the vehicle Preparing the interior: • Sort all loose objects and store them in their respective com- partments. • Store heavy and / or voluminous objects (e.g. radio, outer tent, beverage cases) safely before you start your journey, securing them to prevent them from shifting.

  • Page 15: Driving In Reverse

    Driving in reverse Your HOBBY caravan has a braking system with automatic reverse. It enables you to drive backwards without applying the brakes, becau- se the overrun coupling does not differentiate between overrunning or reversing the caravan.

  • Page 16: After The Drive

    2. Safety Rules for driving in reverse • The caravan tilts in the opposite direction in which you steer. • Use a guide when driving in reverse. Shunting (moving caravan by hand) Your carriage is significantly larger than a car. Rules for moving caravan •...
  • Page 17 2. Safety Redirecting electrical devices Rules for redirecting electrical devices • Open the main shut-off valve on the gas bottle as well as the shut-off valves on the gas-powered appliances you require. • Redirect the refrigerator from 12 V to gas or 230 V. If the caravan socket has been attached to the base vehicle in a manner conforming to standards (DIN ISO 146), the battery of the base vehicle will not...

  • Page 18: Chassis

    For the sake of traffic safety, the vehicle undercarriage must be maintained just as conscientiously as the base vehicle itself. This maintenance should be carried out by your HOBBY dealer. If spare parts are required, use only the original parts designated by the ma- nufacturer.

  • Page 19: Loading

    3. Chassis 3.3 Loading 3.3.1 General information Rules for loading: • Spread the load evenly between the left and right-hand side of the caravan. Heavy or bulky objects belong in the lower storage compartments and near the axle. • If your caravan has a tandem axle: distribute the centre of weight between the two axles.

  • Page 20: Drawbar Load

    1. Gross vehicle weight rating (g.v.w.r.) The indication of the gross vehicle weight rating is taken directly from the HOBBY factory. This mass takes into account the specific operating conditions that are based on the model of the camper and its performance, including such factors as material strength, load- carrying capacity of the axles and tyres, etc.
  • Page 21 These optional extras will be shown in the actual mass of the vehicle if − they are not part of the standard scope of equipment, − Hobby was responsible for assembling them, − the customer can order them. 4. Actual mass Sum of the mass when ready to drive and the optional extras or additional equipment assembled by the manufacturer.

  • Page 22: Safety Coupling Ws 3000

    3. Chassis If the vehicle does not hold the equipment and liquids set out in the table in Item 2 (mass when ready to drive), the loading capacity/additional load (Item 5) can be increased by this value. 3.4 Safety coupling WS 3000 The caravan has been fitted with a safety coupling with tracking stabiliser to prevent it from becoming pendulous or pitching.
  • Page 23 3. Chassis Inspection of hitch • The ball coupling is closed when the lever rests in positi and the green pin of the hitching display is visible. If the WS 3000 is not properly attached to the cou- pling ball, the caravan can detach from the base vehi- cle.

  • Page 24: Front Landing Wheel

    3. Chassis 3.5 Front landing wheel Rotating it upwards and securing it • Hitch the caravan to the base vehicle, aligning the front landing wheel to the rear end of the caravan. • Loosen the tommy screw • Pull the spindle tube up as far as possible.

  • Page 25: Overrunning Equipment And Wheel Brakes

    3. Chassis Rapid-emergency brake The rapid-emergency brake is combined with the hand brake. If the caravan is involuntarily disconnected from the base vehicle, the hand brake will be tightened or moved beyond the dead centre position by the traction force of the rapid-emergency brake .
  • Page 26 3. Chassis Wheel brakes The following information regarding brake adjustment applies for all models with the exception of Premium vehicles. The wheel brakes that have been used are drum brakes that do not automatically adjust. They have an automatic reverse that is sensitive to the course you drive.

  • Page 27: Rotating Stanchions

    3. Chassis 3.8 Rotating stanchions In these models, the hexagon head on which to place the crank is located in the rear of the camper above the opening in the lighting beam. The rotating stanchions are located in the front and rear under the caravan.

  • Page 28: Wheels, Tyres

    Wheels, tyres 4.1 Tyres Only use those tyres designated in the registration documents. Other tyre sizes may only be used with the permission of the ma- nufacturer. • Check tyres regularly to ensure that the tread is worn down evenly; check tread depth; check for external damages. •...

  • Page 29: Profile Depth And Age Of Tyres

    4. Wheels, tyres 4.3 Profile depth and age of tyres New tyres are needed (at the latest) when the profile depth measures 1.6 mm. The minimum tread depth only guarantees minimum safety while driving! Tyres age even when used rarely or not at all.

  • Page 30: Changing The Tyre

    Wheels, tyres Rules for wheel screws: - wheel bolts must first be checked after a distance of 50 km and then checked during regular maintenance. Please note: Tyre bolts for all 13" + 14" metal wheel rims and all light alloy rims (incl.
  • Page 31 4. Wheels, tyres • In the ONTOUR model, the spare tire* is attached by means of a tommy screw to a special holder in the gas bottle container at the front left-hand side of the camper. The spare tire can be removed after the tommy screw has been unscrewed.
  • Page 32 Wheels, tyres The rotating stanchions may not be used as a jack*! After changing the tyre, the wheel screws must be examined (after a 50 km drive) to ensure that they are tight enough (tighten if necessary). Changing the wheel •...

  • Page 33: Tyre Repair Kit

    4. Wheels, tyres Tyre repair kit Do not use the tyre repair kit if the tyre was damaged as a result of driving without air. Small cuts, especially in the tyre tread, can be resealed using the tyre repair kit. Do not remove foreign objects (such as screws or nails) from the tyre.
  • Page 34 Wheels, tyres D Hold the bottle down with the filling tube and then press them together. Press the entire bottle contents into the tyre. Pull the fill hose off and screw the valve insert tightly into the tyre valve with the valve-core remover Press the entire bottle contents into the tyre E Open the air hose on the tyre valve.

  • Page 35: Exterior Structure

    5. Exterior structure De-aerating 5.1 Ventilation and Rules for forced ventilation Proper ventilation and de-aerating of the vehicle is a prerequisite for ideal living comfort. A draft-free forced-ventilation system is located in the floor and a forced de-aerating system is located in the ceiling which should not be interfered with.

  • Page 36: Heating Element

    5. Exterior structure Removing the ventilation grills during maintenance and repair • Push the lock(s) up as far as they will go. • Carefully lift open the ventilation grid on the left-hand side. • Then pull the right-hand side out of the bracket. The ventilation grills must be firmly mounted while driving or when it is raining.

  • Page 37: Opening And Closing Doors And Flaps

    5. Exterior structure 5.2 Opening and closing doors and flaps Keys The following keys are provided with the caravan: - Two keys which fit into the following locks: - entry door, - service flaps, - toilet flap. - gas bottle container lid - fresh-water tank lid - Rear Storage Locker (Premium) External entry door...
  • Page 38 5. Exterior structure Stable entry door The upper and lower parts of the entry door can be opened and closed separately by opening the door and then unlocking the upper part of the door from the lower part. Stable entry door Unlocking the upper part of the door •...

  • Page 39: Entry Step Tread

    5. Exterior structure Pull the plissé and the insect screen on the entry door to the desired position. To open, carefully guide the rail back to the original position in order to fold the plissés correctly. Plissé and the insect screen Entry step tread When entering and exiting the vehicle: •...
  • Page 40 5. Exterior structure Gas-bottle container flap ONTOUR To open • Unlatch the lock with the key. • To unlock, turn the knob that has popped out to a vertical position and open the lid of the gas bottle container. To close •...

  • Page 41: Roof

    5. Exterior structure Toilet flap To open • Unlatch the lock with the key. • Press the knob and swing the flap to the side. To close • Push the toilet flap to the side until it snaps in. • Latch the lock with the key.

  • Page 42: Bicycle Carrier

    5. Exterior structure The caravan has guide rails for skirting in the lower area of the su- perstructure. Always slide the skirting in from the middle of the ve- hicle towards the outer edges. Guide rail for skirting The wheel cover has an integrated keder strip for sliding in the mud- guard.

  • Page 43: Roof Awning

    5.6 Roof awning * Appropriate adapters and fitting components are available for sub- sequent assembly of roof awnings. Please speak to your HOBBY dealer. The roof awning should always be assembled by an authorised specialist. The maximum permissible total width and total height may not be exceeded by installing an awning.

  • Page 44: Interior Structure

    6. Interior structure 6.1 Opening and closing doors, flaps and drawers Furniture doors with a locking mechanism Wall cabinets in the kitchen for ONTOUR, De Luxe (Edition), Excellent, Prestige, Landhaus To open • Press the release and pull on the handle to open the door. To close •...
  • Page 45 6. Interior structure Furniture doors with magnetic safety catches or press locks To open • Pull firmly on the handle until the flap or door springs open. To close • Press on the flap or handle of the door until you can feel that it is held shut by the magnets or locks into place.
  • Page 46 6. Interior structure Furniture doors with a soft close function (optional for ONTOUR) Wall cabinets, stowage cabinets, pantry pull-out To open • Use the handle to pull the door upwards. To close • Use the handle to shut the door until the soft-close function automatically brings the flap to its final position.

  • Page 47: Tv Mount

    6. Interior structure 6.2 TV mount * Extendable flat screen TV • To unlock, press the metal rail and, at the same time, extend the TV mount. 230 V power sockets and an aerial socket for the TV and/or receiver are located directly adjacent to the holder. Extendable flat screen TV Mount for flat screen TV •...

  • Page 48: Hanging Table

    6. Interior structure Hanging table To lower • Raise the front end of the table top by approx. 30°. • Pull down the lower part of the table leg , fold it over by 90° and lay it alongside. • Fold out the supporting legs by 90°.

  • Page 49: Seating Arrangements And Sleeping Areas

    6. Interior structure 6.4 Seating arrangements and sleeping areas The seat groups can be converted into comfortable beds. Converting the Round Seating Arrangement • Remove the seat and back cushions • Lower the table. (see Chapter 6.3). • Replace the seat cushions and pull them to the middle of the table.
  • Page 50 6. Interior structure Bed expansion in the seating arrangement (or model-specific) In some models, the narrow section of the seating arrangement can be widened into a bed. Conversion Pushlock safety catch • Press the pushlock to unlock the flap. • Lay flap fully on the floor in order to raise flap •...
  • Page 51 6. Interior structure Partition for sleeping area Release the clip that fastens the partition and slowly and care- fully slide the partition along the rail guide to close it. The magnetic lock will automatically lock the partition. Securing the partition while driving Head rests (Premium) The head rests can be manually locked into different positions.

  • Page 52: Washroom

    6. Interior structure 6.5 Washroom The shower partition in the rear washroom must be securely fastened when driving. To fold the shower partition out • Loosen the pushbutton • Fold out the handles on the shower partition. • Fold out the shower partition and guide it to the opposite side. Securing the shower partition while driving To shut the shower partition •...

  • Page 53: External Storage Locker

    6. Interior structure 6.6 External storage locker In some models with children's beds, the external storage locker can be selected as an option. When converting to an external storage lock, it is important to en- sure that the lower children's bed is secured using the fastening provided for this purpose.
  • Page 54 6. Interior structure Fully adjustable window stays To open • Should there be a locking knob, press it to work the window latch. • Turn all latches by 90°. • Press the window latch outwards with your hand until it is open as far as you would like.

  • Page 55: Roof Lights

    6. Interior structure Front and kitchen windows Sunshades and insect screens are completely integrated and fully adjustable. To close • Move the handle for the sunshade or the latch for the insect screen slowly and evenly to the desired position. Integrated kitchen window To open •...
  • Page 56 6. Interior structure Large roof light Before opening the light, ensure that the area above the opening of the light is free. The light can be opened to an angle of 60°. To open the roof light • Reach into the opening of the crank bag and fold the crank to the user position by pulling it out.
  • Page 57 6. Interior structure Roof fan (washroom) The roof fan can be set up either on one or both sides. To open • Press the spring lock diagonally upwards towards the inside of the roof fan until it unhooks from its locking mechanism. At the same time, using the handle to press the roof fan up- wards.

  • Page 58: Installation Of Electrical Devices

    7. Installation of electrical devices 7.1 Safety tips The installation of electrical devices in the HOBBY caravan has been carried out in accordance with the valid regulations and standards. Please note • Do not remove safety tips and warnings on the electrical equipment.
  • Page 59 7. Installation of electrical devices TFT control panel (Premium/Landhaus models or optional extra) Wall light/lighting in the seating arrangement Ceiling light Kitchen lighting Outer tent light Therme / boiler Lighting Ambience 1 Lighting Ambience 2 Lighting Ambience 3 Memory Floor heating* Main switch TFT display: see p.
  • Page 60 7. Installation of electrical devices If the ignition of the base vehicle has been switched on, the outer tent light will automatically be switched off. In this case, it cannot be switched on again. Wall lights / lighting in the seating arrangement and Cei ling Lamp • Briefly press the key to switch each lamp on and off. Press longer on the key to regulate how brightly you want the lights to shine.
  • Page 61 7. Installation of electrical devices Kitchen light • Press briefly on the key to switch the kitchen light as well as the spots on and off. Kitchen light Therme with LED display • Press the key to switch the therme on and off. An illuminated LED signals that the therme has been switched on. (LED: only standard panel) • When the main switch is pressed, the therme will also be switched off. • If your caravan has an electric boiler (special request) rather than a therme, the electric boiler will be switched on and off. In the case of some special requests (e.g. Alde heating) this switch has no function even though the control light Truma therme is shining.
  • Page 62 7. Installation of electrical devices Remote control bed • Briefly press the key to switch the - ceiling lighting (in the De Luxe model = ceiling light over the bed) (otherwise = ambient interior lighting) - left bed light - right bed light Remote controls, bed on and off. Press longer on the key to regulate how brightly you want these lights to shine. The brightness you set will be saved; when the lights are switched on again, the brightness you originally set will also be switched on again.
  • Page 63 7. Installation of electrical devices Main menu on the TFT control panel Fixed header A Permanently displays: - date - time - inside temperature - outside temperature Main display B On/Off switch Ein / Aus Schalter Heizung Klimaanlage The current status and values of the available components can for power supply Stromversorgung be viewed at predefined places.
  • Page 64 7. Installation of electrical devices Soft key menu bar C This is used to access the individual menus of the components. Soft keys The “soft keys” are used to carry out the commands displayed in the lower menu bar (C). For example, they enable access to submenus, increase or reduce the values shown, or represent the Return button (“Back” function).
  • Page 65 7. Installation of electrical devices Normally, calibration is carried out automatically, whereby neither the charging nor the discharge current may be more than 150mA. The system can be manually calibrated - while using the 230V mains operation or - if no electrical device has been switched on in 12V operation. To do this, the 30A main fuse must be switched off by pressing the button on the battery container (see “Operation via auxiliary bat- tery”). Now the sensor can calibrate itself. This process takes ap- prox. three hours. If the fuse is then switched on again, a value of 1 should be shown on the display. Exit the menus by using the “Back” function or automatically after one minute.
  • Page 66 7. Installation of electrical devices Heizung TRUMA ULTRAHEAT TRUMA ULTRAHEAT* heating system MA ULTRAHEAT The temperature level (1-6) and performance level (in watts) are dis- played in the menu for the electric auxiliary heating system. The lower menu icon is shown in green when the heating system is in operation. 12:30 23,5 °C 18,0 °C...
  • Page 67 7. Installation of electrical devices ALDE hot water heating system* Heizung ALDE The desired room temperature (in ° C), short-term increase in the amount of hot water for taking a shower (in ° C) and the type of operation (gas/electric) are displayed in the menu for the Alde hot water heating system. The lower menu icon is shown in green when 12:30 23,5 °C 18,0 °C...
  • Page 68 7. Installation of electrical devices Use the arrow (menu bar C) or turn the control knob to select the desired type of operation (highlighted in yellow). Then use the “On/ Off” function or turn the control knob to activate your selection. Please also observe the descriptions in Chapter 10.5 Alde hot water heating system. Info menu 12:30 23,5 °C 18,0 °C 09.01.15 Information on the device manufacturer is shown here. ALDE www.alde.se Service Alde http://www.alde.se/support/ Info: Alde App The submenus shift to the main menu by means of the “Back”...
  • Page 69 12:30 23,5 °C 18,0 °C 09.01.15 DOMETIC 7. Installation of electrical devices 16-31 °C 12:30 23,5 12:30 23,5 °C 18,0 °C 12:30 23,5 °C 18,0 °C 09.01.15 01.15 09.01.15 Setting the temperature 12:30 23,5 °C 18,0 °C 31 °C 12:30 23,5 °C 18,0 °C 09.01.15...
  • Page 70 Info menu on the TFT control panel 12:30 23,5 °C 18,0 °C 09.01.15 Information on the device manufacturer is shown here. HOBBY Hobby-Wohnwagenwerk Ing. Harald Striewski GmbH Harald-Striewski-Strasse 15 24787 Fockbek Deutschland...
  • Page 71 When the device has been connected to the network, call up the URL caravan http://192.168.0.1 in the Internet browser. Submenu To open the data in the web browser, enter the user name “hobby” and the password “caravan” (in this example). The page for opera- ting the devices and switching on the lights will then be displayed.
  • Page 72 7. Installation of electrical devices The current values can be read out here (see also p. 66 for the data from the fixed header A and p. 60 for battery management (only with self-sufficient package). Information The different lights can be switched on and off here. Lighting Devices that are connected to the control panel can also be control- led via the WiFi network. (See also TFT control panel.) Built-in devices (where applicable) The name of the network and the password as well as the access data for the web server can be changed here.

  • Page 73: Electrical Supply

    7. Installation of electrical devices General information regarding the TFT display The time and date are buffered by a 3V 210 mAh, CR2032 type button cell. If, therefore, the time should be incorrect or the clock should stop working, this button cell must be replaced. It is moun- ted on the reverse of the circuit board of the TFT display.
  • Page 74 7. Installation of electrical devices To set up an electric connection • Pull out the 13-pole plug that connects to the base vehicle. • Switch off the automatic circuit breaker by pressing the rocker button down • Take hold of the bottom of the cover flap of the CEE external socket and pull it up. • Completely unwind the connector cable. • Open the cap of the CEE connector plug by pulling it up in a 90° angle. • Insert the plug until it locks into place. • Switch the automatic circuit breaker back on.
  • Page 75 7. Installation of electrical devices Residual current device The standard version of your vehicle is equipped with a residual cur- rent device that will interrupt the electric circuit in case of a possible residual current. Should there be a power failure, the fault current circuit breaker ('fast interrupt' = FI switch) will interrupt the entire 230V electric circuit.
  • Page 76 7. Installation of electrical devices Operation via base vehicle During the drive, the battery of the base vehicle takes over the supply of the 12 V devices if contact 9 of the 13-pole socket sys- tem on the base vehicle has been equipped. Use the main switch on the control panel to switch off the 12 V operation during the drive, on longer stopovers and breaks to conserve power in the base vehicle‘s battery.
  • Page 77 7. Installation of electrical devices Operation via auxiliary battery* (self-sufficient package) • Only accumulator batteries with bound electrolytes (gel or AGM batteries) may be installed in those po- sitions specified by the manufacturer. • The installed battery may not be opened. • When changing auxiliary batteries, use only batteries of the same make and capacity. (Setting the battery type on the control panel: see p. 60) Charge controller in clothes cupboard on wall • Before disconnecting or connecting the auxiliary battery, disconnect the electric connection to the...

  • Page 78: Electrical System

    7. Installation of electrical devices A pushbutton is located directly on the battery container. It is used to disconnect the battery from the 12 V electrical system. At the same time, this button serves as a 30 A automatic circuit breaker. If the caravan is not used for a longer period of time, please dis- connect the battery from the electrical system in order to prevent the battery from being excessively discharged.
  • Page 79 For further information, please speak to your Hobby dealer (also see 6.2). External socket and antenna terminal in the...

  • Page 80: Contact Plan For The Light Control System

    7. Installation of electrical devices 7.5 Contact plan for the light control system Achtung S40 10/11 S38 to charge controller, 230V current from plus input 1 charging current 9 and 13 from car or terminal (only self-sufficient / 12V) connection to charge range 230V ignition...

  • Page 81: Special Lighting

    7. Installation of electrical devices 7.6 Special Lights The switches for the lights described here are located directly on the lights themselves; they are not controlled via the control panel. Corner lights Spotlight and integrated lighting columns can be switched separately.

  • Page 82: Water

    8. Water 8.1 General information We recommend that you inspect any water you have left in the tank, this is very critical before using the wa- ter again • Water that is suitable for drinking should always be used with working with food. This also applies to washing your hands and cleaning the objects that have come into contact with food.

  • Page 83: Water Supply

    8. Water 8.2 Water supply Fresh water tank The tank has a volume of 25 or 50 l (model-specific) and is located either under the bed or in the seating arrangement. The tank is filled with fresh water by means of the filler neck the side wall.
  • Page 84 8. Water Never introduce anti-freeze or other chemicals into the water system. This can be poisonous! When operating during winter ensure that the fresh water tank is sufficiently heated. To remove water • The water will be mixed to the desired temperature according to the position of the pre-mixing unit.
  • Page 85 8. Water Emptying the water system • Use the control panel to switch off the electricity for the water pump by pressing the main switch for a longer period of time (3 - 4 seconds). • Open all of the water taps to the centre setting.
  • Page 86 8. Water Rolling waste water tank The rollable waste water tank can be pushed beneath the vehicle when the caravan is stationary. It collects the waste water and holds 24 litres. The waste water tank can be transported on wheels and has an extendable transport handle , allowing you to transport it to the appropriate waste disposal place for emptying.

  • Page 87: Water Flushing Toilet

    8. Water 8.3 Toilette Preparing the excrement tank Before you can use the toilet, you must first prepare the excrement tank. How to do this is shown in Figures 1 to 11 on the left. Never add sanitary liquids directly through the valve or into the toilet bowl, because this may damage the washer of the valve in the excrement tank.
  • Page 88 8. Water Using the bench toilet In the control panel above, the flush knob is located on the left and the LED of the filling level indicator on the right. It lights up when the excrement tank must be emptied. The lever for opening the slider is located on the left side Pivoting toilet...

  • Page 89: Gas System

    9. Gas system 9.1 General safety rules for the use of liquid gas facilities The gas operation pressure is 30 mbar. You are not permitted to operate the heating system while driving. Inspection of the gas facilities • Have the gas facilities checked by an expert before the first use. • The gas facilities should be inspected by an expert every two years. This inspection should be documented on the inspection certificate in accordance with the German Association of Gas and Water Experts, worksheet G 607, and EN 1949. • Regulator knobs, hoses and waste gas outlets should also be inspected. • We recommend that you replace the safety regulator knob and hose pipes fter 10 years at the latest. Should you discover tears, porous spots or similar defects in the hose, it must be replaced immediately. • The owner/operator is responsible for arranging the inspection. This also applies for vehicles that are not licensed to drive on public roads.
  • Page 90 9. Gas system Regulator knobs and valves • Only use those regulator knobs custom-made for vehicles, with a safety valve. Other regulator knobs are not permissible in accordance with the German Association of Gas and Water Experts, worksheet G 607, and EN 1949. They are not suffici- ent to tolerate the immense strain. • Pressure control devices must have a fixed outlet pressure of 30 mbar. The requirements of EN 12864, Appendix D, apply accordingly. The regulator must have a rate of flow of 1.2 kg/h. Connecting the gas regulator to the gas • Connect the regulator knobs very carefully by hand. do not use bottle keys, pliers or similar tools. • Use the de-icing system (Eis-Ex)* for the regulator knobs when the temperature drops below 5° C. Gas regulator for France and Great Britain Positioning the gas bottle in the gas bottle Due to specific country regulations, the gas regulator in vehicles container exported to France and Great Britain is firmly mounted on the wall...

  • Page 91: Gas Supply

    9. Gas system Never use portable cooking or heating equipment, ex- cept for electrical heating equipment (note the power consumption), but not radiant heaters, because these may cause a fire or risk of suffocation. 9.2 Gas supply The caravan is equipped with propane gas facilities. These facili- ties operate the following devices: - cooker - refrigerator - heating element - special equipment, if necessary - baking oven, if necessary Bottle container The gas bottle container holds two 11 kg propane cylinders Via a safety regulator , the gas bottles are attached by a hose to the supply line . Each bottle must be fastened twice, either by means of two belts or with a belt and a safety mechanism on the floor of the gas bottle container Gas bottles may only be carried in the gas-bottle container. Securing the top of the gas bottle Rules for the gas-bottle container • Before every trip, check that gas bottles are securely fastened.

  • Page 92: Changing Gas Bottles

    9. Gas system Changing gas bottles • Open the flap of the gas bottle container. • Shut the main shutoff valve on the gas bottle. • Manually unscrew the gas pressure regulator and gas hose from the gas bottle (left-handed thread). • Loosen the belts and remove the gas bottle. • Place a full gas bottle back in the gas bottle container. • Lash the fastening strap(s) securely. • Manually screw gas pressure regulator and gas hose onto the gas bottle (left-handed thread). • Close the flap of the gas bottle container. • Open the valve on the full gas bottle that has been connected. • Check whether there is any gas escaping from the tie-in points by spraying them with leak detection spray. Symbols on the gas shutoff spigots Shutoff spigots and valves Heating Baking Gas Refrigerator...

  • Page 93: Gas Socket, External

    9. Gas system 9.3 External gas socket * The external socket for gas is used to connect external gas devices such as a gas barbecue or lamp. The operating pressure of devices to be connected must be 30 mbar. Maximum performance of devices to be connected: 1.5 kW. The plug connection can only be hitched when the emergency shutoff valve has been closed. Push back the clutch sleeve to undo the safety latch. The coupling valve has been constructed in such a way that the emergency shutoff valve can only be opened if a gas hose has been External gas socket attached. When hitching, the plug connection is plugged into the safety coupling.

  • Page 94: Built-In Devices

    10. Built-in devices 10.1 General information In this chapter, you will find information on the devices that have been built into the caravan. This information refers only to the ope- ration of these devices. To some extent, the devices described are special accessories. For further information on the individual built-in devices, please re- fer to the separate operating instructions that have been included in the blue service bag found in the vehicle.
  • Page 95 10. Built-in devices To operate Due to its design, the radiator cover gets hot when the heating is on. The operator is responsible for exercising due diligence so that third parties (especially small children) are not hurt. • Open the valve on the gas bottle and the gas shutoff valve on the gas pipe.
  • Page 96 10. Built-in devices Changing batteries on the automatic ignitor If you cannot hear any ignition sparks or only hear them in intervals of more than one second, then you must insert a new battery. • Ensure that the heating has been switched off. •...

  • Page 97: Electric Auxiliary Heating

    10. Built-in devices 10.3 Electric auxiliary heating* The electric auxiliary heating (Ultraheat) operates only when the caravan is connected to the 230V mains supply The electric auxiliary heating is integrated in the hot-air heating system. This allows for three possible heating methods: - just the gas heater - gas heater + electric heater - just the electric heater...

  • Page 98: Electrical Floor Heating

    10. Built-in devices 10.4 Electrical floor heating* The heating system is located in the middle walking space of the floor. It is 60 cm wide; the length depends on the type of vehicle. This heating system is not meant to heat the room; instead, it reduces the loss of heat via the floor.
  • Page 99 10. Built-in devices Check the amount of liquid in the expansion tank at regular intervals. When the heating is off, the liquid should be approx. 1 cm above the "Min" mark. Modes of operation • LPG operation • Heating cartridge operation (230 V) •...
  • Page 100 10. Built-in devices D E F G H Idle position A. Clock. The clock shows the date and time (when activated). B. *Outside temperature. The outside temperature is displayed. C. Inside temperature. The inside temperature is displayed. D. Circulation pump. This icon is displayed when the circulation pump is in operation.
  • Page 101 10. Built-in devices Hot water The boiler can also be used even if it has not been filled with fresh water. 1. No hot water. If you do not need hot water, press "-". (The icon is empty) It is not possible to make any settings for hot water if the daytime or nighttime automatic system is in ope- ration and you have switched off the hot water.
  • Page 102 10. Built-in devices Heating with electricity Use the following procedure to activate the "Heating with electrici- ty" function. The higher the selected output, the faster the camper will heat up. If electricity and gas are selected together, you can set whether gas or electricity is to take priority (see Tools menu).

  • Page 103: Boiler

    10. Built-in devices 10.6 Boiler The optional boiler holds approx. 14 litres of water. It heats the water electrically using an integrated heating rod. It replaces the standard Truma therme. Before each journey, make sure the boiler has been switched off and then attach the chimney cap. Before operating the boiler you must remove the chimney cap.

  • Page 104: Refrigerator

    10. Built-in devices 10.7 Refrigerator If the external temperature is high, full refrigerating capacity can only be ensured by means of sufficient ventilation.To achieve better ventilation, ensure that the side of the camper with the refrigerator ventilator stands in the shade. Please refer to the manufacturer's separate opera- ting instructions before using the refrigerator.
  • Page 105 10. Built-in devices 12 V operation 12 V operation can only be used while driving, when the motor is running. When resting or if you have stopped for a longer period of time, turn off the 12 V operation and, if required, select another mode of operation.
  • Page 106 10. Built-in devices The freezer compartment is suitable for making ice cubes or for storing frozen food for a short period of time. It is not suitable for freezing food. It is not suitable for freezing food nor for the proper storage of medication.

  • Page 107: Gas Cooker

    10. Built-in devices 10.8 Gas cooker The kitchen segment of the caravan is equipped with a 3-flame gas cooker. Before first use: • Open the bottle valve and the quick-close valve in the gas line. • The roof ventilation or the window must be open while opera- ting the gas cooker.

  • Page 108: Fume Hood

    10. Built-in devices Never allow gas to escape without burning. Danger of explosion! After cooking, leave the glass cover j open until the burners stop giving off heat. Otherwise, the glass cover could burst. Do not store easily inflammable objects such as dish towels, napkins, etc., near the cooker.
  • Page 109 10. Built-in devices Igniter Oven Adjustable knob Grill Please refer to the separate manufacturer's opera- ting manual. Operating the oven Turning on the oven • Switch on the 12 V power supply using the main switch on the control panel. •...

  • Page 110: Microwave

    10. Built-in devices 10.11 Microwave* The kitchen in the camper can be fitted with a 230V microwave, which is installed behind a flap or a sliding door in the kitchen wall cabinet. This device is suitable for defrosting, heating up and cooking food for your personal use.

  • Page 111: Rooftop Air Conditioning

    10. Built-in devices 10.12 Rooftop Air Conditioning The air conditioner is located instead of the roof window on the living room ceiling. To operate the air conditioner correctly and optimize its perfor- mance, you should observe the following: • Ensure sound thermal insulation; seal chinks and cover up glass areas.

  • Page 112: Accessories

    • Any accessories, add-ons, modifications or mounted parts that have not been approved by HOBBY may cause damage to the vehicle and impair its roadworthiness. Even if an expertise, general type approval or design approval has been provided for these parts, this does not ensure the orderly condition of the product.
  • Page 113 11. Accessories Object Weight [kg] Object Weight [kg] Water/gas/electricity Heating/air-conditioning 50 litre fresh water tank (instead of 25 l fresh ALDE hot-water heater COMPACT 3020 28.00 water tank) 28.00 Floor heating up to type 540 4.00 - 6.00 Cable adapter 7/13-pole for connecting cars 0.30 Preparation for roof air-conditioning system 0.50 Charge controller for 12 V power supply Roof air-conditioning system with Booster , battery sensor, and battery DOMETIC FreshJet 1700 / 2200 29.00 / 30.00 container 2.80 TRUMA electric auxiliary heating "Ultraheat"...

  • Page 114: Maintenance And Upkeep

    Rules for maintenance intervals • Have the first maintenance performed by a HOBBY dealer 12 months after the initial registration. • Havve all further maintenance performed once annually at a HOBBY dealer.

  • Page 115: Drawgear

    12. Maintenance and upkeep Greasing and oiling Regularly examine and grease the sliding parts and stationary parts of the chassis. If the caravan is used seldom, yearly mainte- nance is required. Rules for greasing and oiling • Movable parts such as pins and hinged parts on the hand brake lever and deflexion lever of the ramp should be oiled lightly.

  • Page 116: Brakes

    12. Maintenance and upkeep Changing the friction lining It is very easy to exchange the friction pads when they are worn out. Messrs. Winterhoff offer a corresponding set of spare parts. Please note the detailed instructions for assembly in the manufacturer's spare part kit.

  • Page 117: Changing The Taillight Bulbs

    12. Maintenance and upkeep 12.4 Changing the taillight bulbs The following description for changing the rear light bulbs refers to the ONTOUR model. Different rear lights are used in the Premium and Landhaus models. Unfortunately, it is not possible to replace these light bulbs easily. In this case, please speak to your dealer, who will be pleased to assist you in changing these light bulbs Some of the rear lights in the Premium models are...
  • Page 118 12. Maintenance and upkeep • Unscrew the light bulb from the socket and exchange it for a new one. Changing the bulb • Carry out this procedure in reverse to put everything back in place, taking care to ensure that the writing on the lamp not upside down.
  • Page 119 12. Maintenance and upkeep ONTOUR fog tail light • To change the light bulb in the fog tail lamp, unscrew the two screws . Change the light bulb and securely fasten the screws to the cover. Loosen the screws Change the bulb Changing the rear light bulbs in the De Luxe (Edition), Excellent and Prestige models •...
  • Page 120 12. Maintenance and upkeep • Remove the bulb from the socket by turning it. Carry out this procedure in reverse order to install a new bulb and replace the rear light. Remove the bulbs from the socket Changing the battery and maintenance of the smoke detector* Please observe the operating instructions of the device manufacturer.

  • Page 121: Ventilation

    12. Maintenance and upkeep Test • Press the test button for at least 4 seconds until the alarm goes off. The alarm goes off when the electronic system is working. It will stop as soon as you let go of the test button. Test the smoke detector every time the battery has been changed.

  • Page 122: Cleaning The Exterior

    12. Maintenance and upkeep Direct contact with plastics such as PVC, soft PVC and similar pro- ducts (e.g. stickers) must be avoided at all cost. It is not possible to avoid transmitting plasticizers when solvent-based contents come into contact with the aforementioned plastics and this causes the parts to become brittle.
  • Page 123 Rules for damage repair • All damage should be repaired immediately to avoid further damage from corrosion. Consult your HOBBY dealer. Chassis The chassis of the caravan has been specially coated. If the pro- tective coating is damaged, repair it immediately. Coated areas should not be treated with spray oil.

  • Page 124: Cleaning The Interior

    12. Maintenance and upkeep Cleaning the interior To reduce problems arising from dampness, use wa- ter sparingly when cleaning inside. Rules for cleaning seat covers, upholstery covers and curtains • Clean seat covers with a soft brush or vacuum cleaner. •...
  • Page 125 12. Maintenance and upkeep Rules for cleaning the carpet: • Clean with a vacuum cleaner or brush. • If necessary, treat or shampoo with carpet foam. Rules for cleaning PVC surfaces: Sand and dust can damage the surface of a PVC surface that is walked on regularly.

  • Page 126: Winter Lay Up For The Caravan

    12. Maintenance and upkeep The following applies for built-in equipment: • Heating: remove all of the dust that has collected on the heat exchanger, base plate and fan wheel of the hot-air system at least once a year before the caravan season begins. Clean the fan wheel carefully with a brush or small scrubber.

  • Page 127: Winter Operation

    12. Maintenance and upkeep The following applies for tanks and containers: • Clean, disinfect, descale and completely empty all water pipes and faucets. Leave faucets open. • Clean the fresh water tank and empty it by unscrewing the overflow pipe. •...
  • Page 128 12. Maintenance and upkeep Please also refer to the information given by the ma- nufacturers of built-in devices regarding winter. The following applies for ventilation: During operation in winter, condensation is caused when using the caravan in low temperatures. Sufficient ventilation is extremely important to ensure that the quality of the air inside the caravan is good and to avoid damages to the vehicle caused by condensation.

  • Page 129: At The End Of The Winter Season

    12. Maintenance and upkeep The following applies for containers: • If the interior is sufficiently heated, the fresh water tank, water pipes and therme/boiler should not freeze. Fill all of the water containers only after the interior has been thoroughly heated. •...

  • Page 130: Waste Disposal And Environmental Protection

    13. Waste disposal / environmental protection 13.1 The environment and mobile travel Environmentally sound use By nature of their activities, caravan users bear a considerable re- sponsibility towards the environment. Therefore, you should always use your caravan in an environmentally sound manner.
  • Page 131 13. Waste disposal / environmental protection Rules for trash disposal • Separate trash and bring recycleable materials to the appropri- ate collection sites. • Empty trash containers in designated areas as often as possible. This prevents unpleasant odours and trash build-up. Rules for rest areas • Always keep rest areas clean, even if the mess was created by others. • Never dispose of your household trash in the containers provi- ded in rest areas. • Do not let the motor of your base vehicle run unnecessarily while standing still. A cold motor causes a lot of contamination while idling. The quickest way to reach operating temperature is while driving.

  • Page 132: Technical Data

    14. Technical data...

  • Page 133: Chassis Data

    14. Technical data 14.1 Chassis data Trade Tech- g.v.w.r. Per- Axle(s) Wheel Leading Safety Towbar name nical [kg] mitted brake equip- coupling name axle load ment 360 KB T18B • 1100 1100 VGB 13 M 20-2425/1 KFL 12 B WS 3000 H45 One Piece 390 SF P28B •...
  • Page 134 14. Technical data Rims Tyre Floor Total Track Dis- Length Length Total size length width tance length Wheel Size Model towbar caravan mounting 5½ J x 14 5/112, ET 30 Steel 195/70 R 14 XL 3890 2100 1850 3677 4296 4565 5972 5½...

  • Page 135: Possibilities For Increasing Loads

    14. Technical data 14.2 Possibilities for increasing loads Basic version Trade Tech- g.v.w.r. Axle Axle Tyres Brakes Leading Forked name nical [kg] load equip- drawbar name [kg] ment 360 KB T18B • 1100 1100 VGB 13 M 195/70 R 14 XL LI 96 20-2425/1 KFL 12 B One-Piece...
  • Page 136 14. Technical data Maximum increased load g.v.w.r. Axle Axle Additional Wheels Brakes Leading Forked Weight [kg] load New ! rear New ! New ! equipment drawbar [kg] crossbar New ! 1350 1350 1350 1350 1500 1500 VGB 15 MV 201.340.001 185 R 14 C LI 102 KFL 20 A 11,7...
  • Page 137 14. Technical data Basic version Trade Tech- g.v.w.r. Axle Axle Tyres Brakes Leading Forked name nical [kg] load equip- drawbar name [kg] ment 650 KFU C46M 1900 1000/1000 VGB 10 M 155/80 R 13 XL LI 84 20-2425/1 KFL 20 A ZHL 20 A •...
  • Page 138 14. Technical data Maximum increased load g.v.w.r. Axle load Axle Additional Wheels Brakes Leading Forked Weight [kg] [kg] New ! rear New ! New ! equipment drawbar crossbar New ! 2000 1100/1100 VGB 11 M 165 R 13 C LI 91 2200 1200/1200 VGB 13 M...

  • Page 139: Weights Of Vehicle And Equipment

    14. Technical data 14.3 Weights of the vehicles Type Weight Basic Mass in g.v.w.r. Add. load empty equipment running [kg] [kg] [kg] [kg] order [kg] 360 KB ONTOUR 1100 390 SF ONTOUR 1100 460 HL ONTOUR 1026 1088 1200 470 KMF ONTOUR 1050 1097 1300...
  • Page 140 14. Technical data Type Weight Basic Mass in g.v.w.r. Add. load empty equipment running [kg] [kg] [kg] [kg] order [kg] 720 UKFe Prestige 1806 1893 2200 720 UML Prestige 1751 1838 2200 720 KFU Prestige 1835 1907 2200 495 UL Premium 1338 1400 1700...

  • Page 141: Tyres And Rims

    14. Technical data 14.4 Tyres and Rims Standard Metal wheel rims for Light alloy rims for version the standard version the standard version Trade Tech- Axle Metal Tyre size Light Light Light Tyre size g.v.w.r. load wheel pre- alloy alloy alloy pres- name...
  • Page 142 14. Technical data Max. increase Metal wheel rims for Light alloy rims for (for increased load) increased load increased load g.v.w.r. Axle load Metal Tyre size Light Light Light alloy Tyre size [kg] [kg] wheel rim pre- alloy rim, alloy rim, rim, pres- ssure...
  • Page 143 14. Technical data Standard Metal wheel rims for Light alloy rims for version the standard version the standard version Trade Tech- Axle Metal Tyre size Light Light Light Tyre size g.v.w.r. name nical load wheel pre- alloy alloy alloy pres- [kg] name [kg]...
  • Page 144 14. Technical data Max. increase Metal wheel rims for Light alloy rims for (for increased load) increased load increased load g.v.w.r. Axle load Metal Tyre size Light Light Light Tyre size [kg] [kg] wheel rim pre- alloy rim, alloy rim, alloy rim, pres- ssure...

  • Page 145: Tyre Pressure Values

    14. Technical data 14.5 Tyre pressure values As a rule of thumb, it may be assumed that a filled tyre suffers a loss of pressure of 0.1 bar every two months. Check the pressure regularly to avoid damage to tyres or a burst. Tyre size Air pressure in bar 155/80 R 13 XL...

  • Page 146: Index

    Index Index Entry door 33 Accessories 108 exterior 33 Additional equipment 17 interior 33 Additional loads 15 upper part of the door 34 Air-circulation fan 92 Environmental protection 126 Airing 117 Auxiliary battery 73 FI (‚fast interrupt‘) switch 71 Fighting a fire 4 Basic equipment 17 First aid kit 6 Bed conversion 45...
  • Page 147 Index Tyre pressure 24 Tyre profile depth 25 Maintenance 110 Tyre repair kit 29 Mass, definition 16 Tyres 24 Microwave 106 Tyres, age of 25 Oiling 111 Outer tent light 56 Ultraheat 62 Oven 104 Undercarriage 119 Overrunning brake facility 21 Upkeep 117 Plissés 52 Valves 86...
  • Page 148 Hobby-Wohnwagenwerk Ing. Harald Striewski GmbH Harald-Striewski-Straße 15 D-24787 Fockbek/Rendsburg www.hobby-caravan.de...

This manual is also suitable for:

De luxe seriesExcellent seriesPrestige seriesPremium seriesLandhaus series

Table of Contents