Page 1
Dear Camper Owners, We would like to congratulate you on the purchase of your new HOBBY camper and hope that you will always enjoy traveling with it. Please read this manual carefully, even if you have been driving a camper for a longer period of time. It will help you to avoid operating errors and damage to the vehicle and its equipment.
Table of Contents Introduction ..........................01-1 1.1 General information .......................01-1 1.2 Markings in these operation instructions ..............01-2 Safety ............................02-1 2.1 General information .......................02-1 2.2 Before the drive ......................02-2 2.3 Loading ..........................02-4 2.4 Handling Performance ....................02-6 2.5 After the drive ........................02-8 Undercarriage and vehicle registration ................03-1 3.1 General information .......................03-1 3.2 Safety coupling WS 3000 ....................03-3 3.3 Locking brake facilities ....................03-5...
Page 3
7.2 Control panel .........................07-2 7.3 Electrical supply ......................07-4 7.4 Electrical system......................07-7 7.5 External circuit diagram ....................07-9 7.6 Contact plan for the light control system ..............07-10 7.7 Lighting in the camper ....................07-11 Water .............................08-1 8.1 General information .......................08-1 8.2 Tanks ..........................08-2 8.3 Water supply ........................08-3 8.4 Water flushing toilet ......................08-6 Gas system ...........................09-1...
1.1 General information Your HOBBY camper has been built in accor- dance with the latest technology and recognised safety regulations. Despite all of these safety measures, it is possible that people may be hurt...
1.2 Markings in these operation instructions Markings in these operation instructions The handbook explains the camper as follows Texts and illustrations The texts which accompany illustrations are found directly to the right of the illustrations. De- tails in illustrations (here: entry door) are marked with position numbers Lists - Lists are based on key points and are pre-...
2. Safety 2.1 General information Keys The following keys are provided with the camper: - Two keys which .t into the following locks: - entry door, - service flaps, - toilet flap. - gas-bottle container lid - fresh-water tank lid Warnings and information labels are attached both inside and outside the vehicle.
Fighting a .r e • Evacuate all passengers immediately. • Close the main shut-off valve on the gas bottle as well as the shut-off valves on gas- powered appliances. • Shut off the electrical supply • Sound alarm and call the fire department. • Only fight the fire yourself if this is possible without risk. 2.2 Before the drive As the owner and driver, you are responsible for the condition of your vehicle.
Page 9
• If necessary, secure the roof load and lash it to prevent slippage. • If necessary, secure all bicycles and lash them to prevent slippage, ensuring that they do not cover any lighting equipment. • In winter, the roof must be free of snow and ice before you begin to drive.
2.3 Loading Rules for loading: • Spread the load evenly between the left and right-hand side of the camper. Heavy or bulky objects belong in the lower storage compart- ments and near the axle. • If your camper has a tandem axle: distribute the centre of weight between the two axles. • Never focus the load in the camper to the rear (danger of swinging back and forth).
Page 11
1. Determine the maximum drawbar load of your base vehicle by checking its documentation, the type plate or the drawbar plate. 2. Your HOBBY camper has a maximum per- missible drawbar load of 100 kg. 3. Adjust the drawbar load on the camper to the lower of the two values by loading it careful- ly.
2.4 Handling Performance Driving Take a test drive or a safety training course be- fore the first long drive to better acquaint your- self with the carriage in driving conditions. Rules for driving • Do not underestimate the length of the carriage. • Exercise special caution when driving toward yards and through gates. •...
Page 13
Driving in reverse Your HOBBY camper has a braking system with automatic reverse. This makes driving in reverse possible without activating the overrunning bra- ke. However, in addition to rolling resistance, the residual brake force must first be overcome.
When positioning the camper manu- ally, only use the steering handles at the front and rear ends of the cam- per. Never push on the plastic parts or the walls. 2.5 After the drive Choosing a parking place Rules for choosing a parking place: •...
Page 15
Water installation Water left standing in the fresh water tank or the pipes quickly becomes undrinkable. Therefore, check the water pipes and the fresh water tank before each drive to ensure they are clean. If necessary, use a tank cleaner and rinse with sufficient fresh water.
For the sake of traffic safety, the vehicle under- carriage must be maintained just as conscienti- ously as the base vehicle itself. This maintenance should be carried out by your HOBBY dealer. If spare parts are required, use only the original parts designated by the manufacturer.
Page 18
The camper's turning rod spring axle unit is equipped with compact wheel bearings. The cylinder hub, compact bearings and axle nuts form a closed unit. The compact bearings are free of maintenance due to their special grease. The wheel brake may never be repositioned on the fixing lock or on the yoke end of the bars! Only reposition the wheel brake on...
3.2 Safety coupling The camper is equipped with an anti-rolling cou- pling in accordance with ISO 11555-1. This safety WS 3000 coupling stabilises the camper while driving and ensures better driving performance. Please note the additional operating instructions and the manufacturer's safety instructions. WARNING: The laws of physics cannot be defied with a safety hitch.
Page 20
Activation of the stabilization system • To activate the stabilization system, the operation lever must be moved downward out of the closed position until it locks in The spring corpus will become tense in the process, so that contact pressure is created on the coupling ball via the friction elements.
3.3 Locking brake The components of the brake facilities, particu- larly the overrunning equipment, wheel brakes facilities and towbar were checked in accordance with the appropriate EU Guidelines and may only be used in a licensed combination. If you alter or modify any components of the brake facilities, the operation permission loses its validity.
more than approx. 5 mm. In this case, the wheel brakes must be regulated by an experienced shop or, if necessary, the brake shoes must be renewed. • When driving downhill on a moun- tain pass, check to ensure that the brakes are cooled sufficiently.
H SE / H TE may not or cannot be mounted. Please see your Hobby dealer for further information or to have the complete system mounted. 3.6 Rotating stanchions The rotating stanchions are located in the front and rear under the camper.
The crank for the rotating stanchions is located at the front in the gas-bottle container. It is atta- ched firmly to the bottom of the container. 3.7 Vehicle registration Every vehicle which uses public roads is subject to registration. This includes your new camper. You can register the camper at your local regis- tration office.
Page 25
Name plate Permit number Vehicle ID number (FIN) Permissible maximum weight Permissible axle load, st axle Permissible axle load, 2nd axle The name plate is located in the lo- wer front area on the right-hand side wall. Do not remove or change the name plate.
3.9 Fit for a Speed of 100 km/h 1. Your HOBBY camper is technically equipped for a maximum speed of 100 km/h. Under no circumstances may this speed be exceeded! 2. Note the permissible maximum speeds for trailer carriages in the country in which you are travelling! 3.
5. Additional equipment Additional equipment includes all items not part of the standard equipment preinstalled in the HOBBY factory or by the dealer. This also includes installations by special request. The mass in running order refers to the vehicle as originally equipped by the dealer or factory.
Page 28
If you are not sure whether you have overloaded the vehicle, weigh your vehicle on a public vehicle scale. Overloading can lead to malfunction or even tire blowout! This presents the danger of the vehicle spinning out of control, which endangers you as well as other dri- vers and pedestrians.
4. Wheels, tires Only use those tires designated in the registra- tion documents. Other tire sizes may only be 4.1 Tires used with the permission of the manufacturer (ABE). • Check tires regularly to ensure that the tread is worn down evenly; check tread depth; check for external damages.
If the tire pressure is too low, the tire can overheat. This can result in serious damage. The correct tire pressure is given in the table on wheels/tire pressure found under "Technical Information" or on the labels in the gas-bottle container and on the wheel cover.
4.4 Rims Only use rims that are covered by the vehicle licence. Should you wish to use other rims, please note the following: Rules for the use of other rims: - Size, - mechanisms, - compression depth and - the load/bearing capacity must be sufficient for the permissible total mass.
4.5 Changing the tire Preparing to change the tire • If possible, only change the tire when the base vehicle is coupled to the camper. • Park the trailer carriage on as firm and even a surface as possible. • If you have tire trouble on a public road, turn on your hazard warning signal lights and set up the warning triangle.
Page 33
Warnings for changing the tire: Only use the specifically designated jack for the corresponding frame parts. For example, on the axle pipe corre- sponding to the swinging lever group or on the stringer in the area of the axle fasteners. Damage or even an accident result- ing from the vehicle's toppling over can occur if the jack is applied to...
Page 34
the attachment torque is 0 nm for steel rims and 20 nm for aluminium rims. • Release the handbrake and reactivate the stabilization system. You should have a functional spare tire available at all times. Therefore, have the spare tire replaced without delay.
Page 35
D Hold the bottle down with the filling tube and then press them together. Press the entire bottle contents into the tire. Pull the fill hose and screw the valve insert tightly into the tire valve with the valve-core remover E Open the air hose on the tire valve.
5. Exterior structure 5.1 Ventilation and De-aerating Rules for forced ventilation Proper ventilation and de-aerating of the vehicle is a prerequisite for ideal living comfort. A draft- free forced-ventilation system is located in the floor and a forced de-aerating system is located in the ceiling which should not be interfered with.
Page 38
Special cover plates should be used during winter operation. You can buy these cover plates from your dealer. We recommend that you remove the ventilation bars when outside tem- peratures are very high. This creates a high air circulation on the refrigera tor and increases cooling capacity.
5.2 Entry door External entry door To open • Turn the key to the left until you hear the lock open. • Turn the key back to an upright position and pull it out. • Pull on the door handle. •...
Page 40
Internal entry door To open • Reach into the grip plate , pull the release lever, open the door and let go of the lever. To close • Pull the door shut. • Press the locking button In this manner, a door locked from the outside can be opened from the inside.
Never close the upper part of the door if the insect screen is closed. The insect screen must always be open when you lock the door. Locking the upper part of the door • Turn the lever 90° to the right and back into an upright position to connect the upper and lower parts of the door.
All of the fastenings on the service flap must lock into place when closing to ensure that the flap will always be closed tight. If the flap is not closed correctly, it could become perma- nently deformed, especially when the camper stands unused for a longer period of time.
5.6 Roof The following applies for the roof load • Use only standardised and licensed ladders that can be positioned firmly to climb onto the roof. • The roof has not been made for concentrated loads. Place a large-scale cover over the area you wish to step on before standing on the roof.
Fastening for the outer tent Use the specially developed Hobby Vario Clip as a ridgepole bracket to securely attach an outer tent to the camper. The clip can be attached without screws and has been specially adapted to the contour of the moulding. The moulding is lined in the relevant places with a pressure and moisture-resistant plastic honeycomb design.
6 Interior structure 6.1 Opening and closing doors and .aps Stowage and wall cabinets To open • Press the pushbutton on the handle to unlock the .ap. • Pull on the handle until the flap opens. To close • Use the handle to press the flap shut until you can feel it lock.
Page 46
Furniture doors with knob Wardrobe • Turn the knob to open and shut the door. Push-lock drawers Kitchen drawer To open • Press the push-lock until the knob jumps • Pull on the handle until the drawer slides out. To close •...
6.2 Pivoting TV cabinet Media oval (model-specific) The media oval is a room divider, mounted on a pivot, which can be used as both a bar and a TV cupboard for flat screens. To swing the media oval, pull the catch and, after swinging out the media oval, press and snap the catch back into place to secure the...
6.3 Extendable media shelf (model-specific) The extendable media shelf is an extenda- ble, pivot-mounted room divider which can be used both as a bar and as a TV cabinet for flat screens. To pull out the room divider, pull the knob out;...
6.4 Tables Elevating table To lower • Turn the locking bolt 180°. • Press on table top to lower the table. • Turn the locking bolt back and secure the table top. To turn • Loosen the knurled screw • Turn the table in the desired (excentric) direc- tion.
Page 50
Swivelling table To lower • Push the handle upwards. • Swivel the table top downwards in an arc until the handle locks into place. To turn • There are rollers on the table legs, shifted 45°, which enable the table to be turned around its centre point in any desired direction.
6.5 Conversion of seats and beds The seat groups can be converted into comfor- table beds. Conversion • Remove the seat and back cushions • Lower the table. • Replace the seat cushions and pull them to the middle of the table. •...
Bed expansion for vehicles with side sea- ting arrangement • To open, press the push lock • Carefully place the external panel on the floor. • Place the additional panel for the bed in a horizontal position or tilt its longitudinal side slightly upwards.
6.7 Windows Hinged windows To open The window can be adjusted to open at varying degrees: • Turn the latch into the vertical position. • Press the window outward until you hear a click. The window automatically remains in this position. Windows by the children's beds are secured against accidental opening, to effectively prevent children from...
6.8 Roof bonnets Safety instructions • Never open the roof bonnets in a strong wind or when it is raining, hailing, etc., or if the outside tem- perature is below -20° C! • Never use force to open the roof bonnets if they are frozen or cove- red with snow, because you may break the hinges and the opening...
Page 55
Small roof bonnet To open the roof bonnet • This roof bonnet can be opened to three different settings in the opposite direction to traffic. Press the locking knob on the side and use the adjusting lever to move the roof bon- net to the desired position;...
Page 56
To avoid consequential damage, leave the shades and pleatings open when the caravan is not in use. Shade The shade is infinitely variable; simply pull the handle to the desired position or until the lock snaps into the handle of the insect screen. Opening/closing the insect screen Push the handle strip of the insect screen against the handle strip of the pleating until the...
7. Installation of electrical devices 7.1 Safety tips The installation of electrical devices in the HOB- BY camper has been carried out in accordance with the valid regulations and standards. Please note Do not remove safety tips and war- nings on the electrical equipment. The installation spaces for electrical equipment such as distribution fuse boards, electric power supply, etc.,...
7.2 Control panel Water level indicator Functions of the main switch Therme • After initially connecting the camper to the 30 V mains, you must press either the main switch or any other control key in order to Floor heating activate all of the V electrical devices and the 30 V electrical devices that are switched Outer tent light...
Page 59
• The charge level indicator (only self-sufficient) shows the current charge level of the battery. Blinking red light: The battery is not connected or has been exhaustively discharged; the battery will not be charged. Start to charge the battery by pressing on the activation key on the charge controller.
7.3 Electrical supply Electricity for the camper can be obtained from the following connections: - 30 V mains connection 50 Hz - via the base vehicle if it is connected using the 13-pole plug (limited functions) - via a built-in auxiliary battery (special request) Everything that uses V, such as lighting, water supply, etc., is available.
Page 61
Rules for the mains connection • Use only a 3 x .5 mm cable with a maximum length of 5 m, a CEE plug and connector to connect the camper to an external 30 V mains. When obtaining electricity via a cable drum, this must be completely unwound, as otherwise induction may cause the cable to heat up,...
Page 62
Operation via auxiliary battery (self-sufficient package) • Only accumulator batteries with bound electrolytes (gel batteries) may be installed in those positions specified by the manufacturer. • The installed gel battery may not be opened. • When changing auxiliary batteries, use only batteries of the same make and capacity.
• Always charge the auxiliary battery for at least 0 hours before each journey, directly after each journey and before you take the camper temporarily out of service. • Use every opportunity during your journey to charge the battery. • The battery loses its capacity after having been used for a while and at low temperatures.
Page 64
This can be used, for example, to set up a TV in the outer tent. Depending on how you wire it, the integrated antenna terminal can be used as either an input or an output socket. For further information, please speak to your Hobby dealer (also see 6.2). 07-8...
7.6 Contact plan for the light control system 230V current range Therme Floor heating Plus electrical supply Fuses 5A Input lead Earthing Protective conductor electrical supply Wall light dimmer Ceiling light Children's Children's Water Clothes dimmer bed lights bed lights supply cupb.
7.7 Lighting in the camper Circumferential recessed spotlights by the seating arrangement Corner shelf: Spotlight and integrated lighting columns can be switched separately. Indirect lighting above the stowage cabi- nets: Dimmable wall lights Dimmable ceiling light 07-...
Page 68
Indirect lighting above the window by the main seating arrangement Ceiling light above the middle seating ar- rangement (depending on the model) can be switched manually directly on the lamp. Oval light and kitchen light above the kit- chen worktop: The clothes cupboard light is switched on and off by opening the doors of the cupboard...
Page 69
If the camper socket has been attached to the base vehicle in a manner conforming to stan- dards, Hobby‘s light control system will auto- matically switch off the outer tent socket when an electric connection is set up for the camper using the 3-pole plug.
8. Water 8.1 General information The entire water system in your cam- per consists mainly of materials sui- table for drinking water and, in part, of food-safe materials. Despite this, we recommend that you inspect any water you have filled in very critically before using it.
• Protect the pump from freezing. • Hard blows or hits as well as very dirty water can destroy the pump. • The pump can transmit at most 8.5 l/min. 8.2 Tanks Built-in fresh water tank The tank has a model-specific volume of 25 or 50 litres.
During the trip, the waste water tank can be stored in the gas-bottle container to save space. Empty the waste water tank before beginning your journey and then use the belt in the gas-bottle container to secure it. Empty the waste water tank if there is danger of frost.
Page 74
To remove water • The water will be mixed to the desired temperature according to the position of the pre-mixing unit. Emptying the water system • Use the control panel to switch off the elec- tricity for the water pump by pressing the main switch for a longer period of time (4 sec.).
Page 75
• Empty the therme at the risk of frost. Frozen water can cause the therme to burst! • A depressuriser must be used if the pump is connected to a central water supply, or on stronger pumps. The pressure in the therme may not exceed .2 bar.
8.4 Water flushing toilet Toilets with .xed seat and fr esh water tank To prepare the toilet 1. Open the service flap on the exterior wall of your camper. 2. Swing the fill stanchions of the faeces tank in a 90° arch and remove the water tank exten- sion (located under the handle closest to the drain nozzle).
Page 77
5. Remove the extension and return it to its ori- ginal position on the faeces tank. Depending on the amount of space between the door and the faeces tank, you can also use a peg to fasten the extension to the door. Screw the cap back onto the wa- ter funnel and press it back inside towards the fresh water tank.
Page 78
0. Push the faeces tank through the door back to its original position. Do not use force the faeces tank back in; this could lead to severe damage. . Use the securing clamp to ensure that the faeces tank is locked into place and close the service flap.
Page 79
4. Ensure that the valve is closed. Open the service flap on the outside of the camper. Pull the holder clamp up and remove the faeces tank. 15. Remove the water tank extension first to pre- vent its being lost when emptying the faeces tank.
Page 80
9. If necessary, prepare the toilet once again for use. Replace the water tank extension in its original position on the faeces tank. Push the faeces tank back into the toilet and close the service flap. Storage If you do not plan to use your Thetford toilet for a longer period of time, it is important that you follow these instructions first: Drain the water from your camper's central water...
9. Gas system 9.1 General safety rules for the use of liquid gas facilities The gas operation pressure is 30 mbar. Inspection of the gas facilities • Hae the gas facilities checked by an expert before the .rst use. • The gas facilities should be inspected by an expert every two years. This inspection should be documented on the inspection cer- tificate in accordance with the German Asso- ciation of Gas and Water Experts, worksheet...
Page 82
• Pressure regulators must have a fixed output pressure of 30 mbar. The requirements of EN 12864, Appendix D, apply accordingly. The regulator must have a rate of flow of 1.2 kg/h. • Connect the regulator knobs very carefully by hand.
9.2 Gas supply The camper is equipped with propane gas facilities. These facilities opeate the following devices: cooker refrigerator heating element warm water boiler, if necessary special equipment, if necessary - baking oven, if necessary Bottle container Der Gasflaschenkasten fasst 2 x 11 kg Pro- pangasflaschen .
Page 84
Changing gas bottles Never smoke or light open fires when changing gas bottles. After changing bottles, check whether gas is escaping from the points of attachment by spra- ying these with a leak indicator. • Open the flap of the gas-bottle container. •...
10. Built-in devices 10.1 General information In this chapter, you will .nd information on the devices that have been built into the camper. This information refers only to the operation of these devices. To some extent, the devices described are special accessories. For further information on the individual built-in devices, please refer to the separate operating instruc- tions that have been included in the blue service...
10.2 Hot-air heating Heating while driving is forbidden. Place of installation In the closet or the corner of the flue Before .rst use • Several air outlet nozzles have been built into the camper. Pipes lead the hot air to the air outlet nozzles.
Page 87
• If the flame extinguishes again, re-ignition takes place during the closing phase of the fusible cut-out of the ignition safety switch (approx. 30 seconds). • If no flame is ignited, the automatic ignitor will continue to work until the operation handle is switched to “0”.
Page 88
Circulation fan The heating system in your camper has been fitted with a recirculation air system which distri- butes the hot air throughout the entire interior by means of several air vents. The air vents can be turned and opened individually, enabling the hot air to escape with the corresponding intensity to where it is required.
10.3 Electric auxiliary heating The electric auxiliary heating (Ultrahe- at) operates only when the camper is connected to the 230V mains supply. The electric auxiliary heating is integrated in the hot-air heating system. This allows for three pos- sible heating methods: - just the gas heater - gas heater + electric heater - just the electric heater...
10.4 Electrical floor heating The heating system is located in the middle walking space of the floor. It is 60 cm wide; the length depends on the type of vehicle. This he- ating system is not meant to heat the room; in- stead, it reduces the loss of heat via the floor.
10.5 Hot-water heating system You are not permitted to operate the hot water heater while driving. The Compact 3010 LPG heater is a hot-water heating system which heats hot water separately (contents: 8.5 l). It is possible to heat up the he- ating system without filling the hot-water heater with fresh water.
Page 92
lights up and those functions that can be set will start to blink. Use the arrows to select the func- tion you wish to set. Settings are saved automa- tically. For further detailed information on operation, handling and maintaining the hot-water heating system, please refer to the separate operating in- structions for “Alde Compact 3010”.
Page 93
Press the -/Off button. The „Off“ sign (main blinkar blinkt switch) will blink on the display. The settings are now complete. The „Off“ sign (main switch) is shown on the display when the control unit is in an idle state. Setting the desired temperature blinkar blinkt...
Page 94
Turn on the hot water by pressing on the +/ON blinkar blinkt button. „ON“ appears on the display next to the temperature. The symbol for hot water is shown when the control unit is back in an idle state. Press the button with the arrow until the symbol blinkar blinkt for hot water blinks.
Page 95
Activate heating with gas by pressing on the blinkar blinkt +/On button. „ON“ appears on the display next to the temperature. The symbol for heating with gas is shown on the display when the control unit is in an idle state again.
Page 96
Select the power setting (1kW, 2kW or 3kW) by blinkar blinkt pressing the +/On or the -/Off button. In the illus- tration, the 3kW power setting has been selected (some heaters are only equipped with 1-2kW). The symbol for electric heating is shown when the control unit is back in an idle state.
10.6 Boiler The boiler holds approx. 14 litres of water. It uses gas to heat the water or, depending on the model, there is also an option to heat it electri- cally using an integrated heating rod. Before each journey, make sure the boiler has been switched off and then attach the chimney cap.
Page 98
Operating on gas • Remove the chimney cap. Boiler • Open the gas bottle and the emergency shut- off valve on the gas pipe. • Use the rotary switch on the control panel to switch on the boiler. The green control light will shine.
10.7 Refrigerator Your camper is installed with a refrigerator made by Dometic or Thetford. If the external temperature is high, full refrige- rating capacity can only be ensured by means of sufficient ventilation. If necessary, to achieve better ventilation, the refrigerator’s ventilation grille can be removed at the campsite.
Page 100
and the gas shutoff spigot marked “refrigera- tor”. • Turn the thermostat up full and keep it pressed down. The refrigerator will either ignite automatically or by using the knob for manual ignition (depending on your model). • When it is ignited, let go of the thermostat. Repeat the previous step if it has not ignited.
Freezer compartment If the outside temperature and the rate of humi- dity are very high, drops of water may form on the metal frame of the separate freezer compart- ment. For this reason, it has been fitted with a frame heater (Dometic only). If the outside tem- perature and the rate of humidity are very high, switch the frame heater on by pressing .
Page 102
Operation • Open the cover • Set the turning knob of the desired burner in the ignition position (large flame) and press. • Ignite the burner with gas lighter fluid, a match and/or lighter. (Spinflo cooker: press the igniter • Hold the turning knob in for an additional 10-15 seconds.
10.9 Fume hood As an option, the kitchen can be fitted with a fume hood. The built-in fan blows kitchen odours directly outside. Press the right button to turn on the fume hood. Hold the fan button firmly to select the speed of the fan from among 15 different speeds.
Page 104
• Never operate the oven when it is empty (i.e., without food that is to be heated). • The grill (special equipment; not part of standard delivery) should never be used for longer than 25 minutes and only operated when the oven door is open.
• Any accessories, add-ons, modi.cations or mounted parts that have not been approved by HOBBY may cause damage to the vehicle and impair its roadworthiness. Even if an expertise, general type approval or design approval has been provided for these parts, this does not ensure the orderly condition of the product.
.xed maintenance intervals apply to the camper and the devices installed in it. Rules for maintenance intervals • Have the first maintenance performed by a HOBBY dealer 12 months after the initial registration. • Havve all further maintenance performed once annually at a HOBBY dealer.
Rules for greasing and oiling • Have the swinging lever bearings greased after every 2,000 to 3,000 kilometers driven. • Grease the bearing spaces on the casing of the overrunning system. • Oil movable parts such as bolts and joints. •...
Page 109
Changing the friction lining The front friction lining can be changed in case of excessive wear. Note the detailed as- sembly instructions in the manufacturer's set of spare parts. The rear friction lining has such a large dimension that it does not have to be replaced.
12.3 Changing the taillight bulbs Carefully remove the protective caps with a screwdriver. Remove the four fastening screws with a crosstip screwdriver. Now you can remove the taillight from the frame. Remove the holder by loosening the screw. The bulbs are now freely accessible. Put the taillight back together by repeating the process in reverse.
Sufficient ventilation and de-aeration of the vehi- 12.4 Ventilation cle interior is essential to maintaining a com- fortable climate. In addition, corrosion damage from sweat residue can be avoided. Sweat residue forms most readily - in tight spaces, - from the breath and perspiration of the passen gers, - by carrying in damp clothing, - when operating the gas cooker.
Page 112
Dry spotlight and lamp frames thor- oughly, since water can build up in these areas very easily. Never use caustic cleaners or clea- ners which contain solvents. Cleaning with a high-pressure cleaner Labels and exterior decorations should not be sprayed directly with a high-pressure cleaner, because they may come off.
Page 113
Rules for damage repair • All damage should be repaired immediately to avoid further damage from corrosion. Con sult your HOBBY dealer. Undercarriage The undercarriage of the camper has been spe- cially coated. If the protective coating is dama- ged, repair it immediately.
Page 114
Do not use strong and aggressive cleaners which contain softeners or solvents! Talcum is available in auto specialty stores. Cleaning the interior Rules for cleaning seat covers, upholstery covers and curtains • Clean seat covers with a soft brush or vacu- um cleaner.
Page 115
Rules for cleaning the toilet area • Clean with neutral liquid soap and a non- scouring cloth. • Do not use a vinegar concentrate to clean the toilet and the water system or to decalcify the water system. Vinegar concentrate can dam- age gaskets or parts of the system.
Page 116
12.6 Winter operation Preparation Due to the overall vehicle conception, (aluminium sandwich construction with insulated windows) your camper is suitable for winter operation. WARNING: We recommend that you optimise your camper in accordance with your personal tastes for winter camping. Your dealer will gladly advise you in these mat- ters.
Winter operation In the course of winter operation, condensati- on forms at low temperatures when the vehicle is occupied. Sufficient ventilation plays a very significant role in ensuring a suitable air quality within the vehicle and preventing damage by condensation. Rules for ventilation •...
Page 118
After the end of the winter season Rules for upkeep • Carry out a thorough undercarriage wash. This removes thawing agents (salts, lye resi- due). • Clean the exterior of the camper and use commercially available car wax to preserve steel parts.
13. Waste disposal and environmental protection 13.1 The environment and mobile travel Environmentally sound use By nature of their activities, camper users bear a considerable responsibility towards the environ- ment. Therefore, you should always use your camper in an environmentally sound manner. Rules for environmentally sound use •...
Page 120
Rules for the disposal of faeces • Only add approved cleaners to the faeces tank. The use of other cleaners can be avoided by the installation of an active charcoal filter system. Apply cleaning fluid very sparing- ly. Excessive application does not guarantee the prevention of odour build-up! Disposal •...
Mass in g.v.w.r. Add. load empty equipment running [kg] [kg] [kg] [kg] order [kg] 400 SF De Luxe 1100 400 KB De Luxe 1100 440 SF De Luxe 1057 1200 455 UF De Luxe 1050 1112 1300 460 UFe De Luxe...
Page 122
Type Weight Basic Mass in g.v.w.r. Add. load empty equipment running [kg] [kg] [kg] [kg] order [kg] 455 UF Excellent 1052 1114 1300 460 UFe Excellent 1068 1130 1300 495 UL Excellent 1168 1230 1400 495 UFe Excellent 1137 1199 1400 500 KMFe Excellent 1183...
14.4 Technical data Trade Tech- g.v.w.r. Permitted Axle Leading Towbar Wheel name nical [kg] axle load equipment brake desi- gnati- 400 SF 30 A • • 1100 1100 DB 13 M KFL 12 B One Piece 20-2425/1 400 KB 30 A •...
Page 125
Trade Tire Fitting Wheel Floor Total Track Length Length Total name size dimensions [bar] length width stance length towbar caravan 400 SF 195/70 R 14 5/112, ET 30 5½ J x 14 3833 2200 1950 3618 4109 4702 5899 400 KB 195/70 R 14 5/112, ET 30 5½...
14.5 Possibilities for increasing loads Basic version Trade Techni- g.v.w.r. Axle load Axle Tires Brakes name [kg] [kg] desi- gnation 400 SF 30 A • • 1100 1100 DB 13 M 195/70 R 14 LI 91 20-2425/1 400 KB 30 A •...
Page 127
Possible increased load Leading Forked g.v.w.r. Axle load Axle Additional Wheels Brakes Leading Forked equipment drawbar [kg] [kg] New ! rear New ! New ! equip- drawbar crossbar ment New ! KFL 12 B One-Piece 1350 1350 185 R 14 C LI 102 KFL 12 B One-Piece 1350...