Table of Contents
Advertisement
COMMUNICATION settings / Connecting to a personal computer
RS-232C settings
This connection can be used for remote control and re-
cording supplementary information when the main unit is
connected to a PC.
Transmission speed
Example: Transmission speed is set for 4800 bps.
1. Press the SET UP button to display the <MENU SETTING>
menu.
2. Turn the JOG dial to move the cursor to C O M M U N I C A -
TION SETTING then turn the SHUTTLE ring to the right.
• The <COMMUNICATION SETTING> menu will appear.
<COMMUNICATION SETTING>
@RS-232C SETTING
3. Check that the cursor is next to RS-232C SETTING and
turn the SHUTTLE ring to the right.
• The <RS-232C SETTING> menu will appear.
<RS-232C SETTING>
@TRANSMISSION RATE
4. Check that the cursor is next to TRANSMISSION RATE
and turn the SHUTTLE ring to the right to flash the sub-item.
<RS-232C SETTING>
@TRANSMISSION RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT LENGTH
DELIMITER
5. Turn the JOG dial to select "4800" and turn the SHUTTLE
ring to the right to finish setting.
<RS-232C SETTING>
@TRANSMISSION RATE
6. Press the SET UP button.
• The <RS-232C SETTING> menu will disappear.
TCP / IP settings
The IP address, subnet mask setting, and MAC address
used to specify the connected recorder can be referred to
here (refer to page 8).
Press the COMMUNICATION button on the unit's
front face to activate the TCP/IP communication
function.
1. Press the SET UP button to display the <MENU SETTING>
menu.
2. Turn the JOG dial to move the cursor to C O M M U N I C A -
TION SETTING then turn the SHUTTLE ring to the right.
• The <COMMUNICATION SETTING> menu will appear.
<COMMUNICATION SETTING>
@RS-232C SETTING
3. Turn the JOG dial to move the cursor to TCP / IP SETTING
then turn the SHUTTLE ring to the right.
• The <TCP / IP SETTING> menu will appear.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
TCP/IP SETTING
1200
DATA BIT LENGTH
8BIT
PARITY BIT
NONE
STOP BIT LENGTH
1BIT
DELIMITER
CR
1200
8BIT
NONE
1BIT
CR
4800
DATA BIT LENGTH
8BIT
PARITY BIT
NONE
STOP BIT LENGTH
1BIT
DELIMITER
CR
TCP/IP SETTING
<TCP/IP SETTING>
@SELF IP ADDRESS
000.000.000.000Ł
SUBNET MASK
000.000.000.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF
4. Check that the cursor is next to SELF IP ADDRESS and
turn the SHUTTLE ring to the right to flash the sub-item .
<TCP/IP SETTING>
@SELF IP ADDRESS
000.000.000.000Ł
SUBNET MASK
000.000.000.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF
5. Turn the JOG dial to input the SELF IP ADDRESS and turn
the SHUTTLE ring to the right to finish setting.
<TCP/IP SETTING>
@SELF IP ADDRESS
192.168.001.100Ł
SUBNET MASK
255.255.255.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF
6. Press the SET UP button or turn the SHUTTLE ring to the
left.
• The <TCP/IP SETTING> menu will disappear.
Connecting with a personal computer
This connection can be used for remote control and re-
cording supplementary information when the main unit is
connected to a PC.
Please use RS-232C Straight cable (9pin) to con-
nect a modem with this unit. The setting of CTS
should be set to "HIGH" or "ON". Please refer to the
instruction manual of a modem for details about con-
nection.
Connection via modem
CAMERA IN
VIDEO OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CAMERA OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Modem
Y/C
GND
GND
ON
OFF
SCSI
ETHERNET
ALARM IN
RESET
RS-232C
TERMINATION
SCSI
RS-232C straight cable (9 pin)
Direct connection
CAMERA IN
VIDEO OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CAMERA OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Y/C
GND
GND
ON
OFF
ETHERNET
ALARM IN
RESET
SCSI
RS-232C
TERMINATION
SCSI
Please use RS-232C crossover cable (9pin) to
connect a modem with a personal computer. RS -
232C Crossover cable differs depending on the per-
sonal computer.
Personal Comput
phone line
Modem
Personal Computer
RS-232C crossover cable
65
Advertisement
Table of Contents
