Table of Contents
Advertisement
@INITIAL SET UP
2. Move the cursor to ARCHIVE OVERWRITE and turn the
SHUTTLE ring to the right until the sub-item flashes.
<INITIAL SET UP>
@ARCHIVE OVERWRITE
3. Turn the JOG dial until "ON" flashes and turn the SHUTTLE
ring to the right.
• The sub-item stops flashing.
<INITIAL SET UP>
TIME DATE ADJUST
HDD FULL
HDD PB REPEAT
@ARCHIVE OVERWRITE
The Archive Pointer
backup is either temporarily stopped or finished.
Using this, the unit will begin the next backup at the
end point of the previous backup.
4. Turn the SHUTTLE ring to the left or press the SET UP
button.
<INITIAL SET UP>
@ARCHIVE OVERWRITE
Auto-eject setting
This setting is for ejecting the medium of an archive device
automatically. If you set to "ON" and make the back up
timer program, the archive medium is ejected automati-
cally at the end of the programmed time. If you set to "OFF",
the archive medium will not be ejected.
Example: Setting AUTO EJECT to "OFF" (the default is
"ON").
1. Display the <MENU SETTING> menu on the screen and
turn the JOG dial until the cursor is next to INITIAL SET UP
and turn the SHUTTLE ring to the right.
• The <INITIAL SET UP> menu appears.
<INITIAL SET UP>
@TIME DATE ADJUST
2. Turn the JOG dial until the cursor is next to AUTO EJECT
and turn the SHUTTLE ring to the right.
• When the sub-item is flashing, turn the JOG dial until "OFF"
starts flashing.
3. Check "OFF" is flashing and turn the SHUTTLE ring to the
right.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
COMMUNICATION SETTING
REAR TERMINAL
SERVICE
TIME DATE ADJUST
STOP
HDD FULL
HDD PB REPEAT
STOP
OFF
AUTO EJECT
ON
ALL
ARCHIVE DATA
OFF
MOTION DETECTION
LANGUAGE SELECTION
STOP
STOP
ON
Glossary
is recorded when
TIME DATE ADJUST
HDD FULL
STOP
HDD PB REPEAT
STOP
ON
AUTO
EJECT
ON
HDD FULL
STOP
HDD PB REPEAT
STOP
ARCHIVE OVERWRITE
OFF
AUTO EJECT
ON
ARCHIVE DATA
ALL
HDD PB REPEAT
STOP
ARCHIVE OVERWRITE
OFF
@AUTO EJECT
OFF
ARCHIVE DATA
ALL
HDD PB REPEAT
ARCHIVE OVERWRITE
@AUTO EJECT
ARCHIVE DATA
4. Turn the SHUTTLE ring to the left or press the SET UP
button.
Archive medium is also ejected when the ARCHIVE
button is pressed once again, after operation has been
initiated with the ARCHIVE button. Refer to page 62,
"Auto-eject at the completion of backup" for details.
ARCHIVE DATA setting
When backing up records onto backup media, it is possi-
ble to select and back up only the "ALARM" part of the
records by setting ARCHIVE DATA to "ALARM".
Example: Setting backup operation selection to "ALARM"
(the default is "ALL").
1. Press the SET UP button to display the <MENU SETTING>
menu.
2. Move the cursor to INITIAL SET UP and turn the SHUTTLE
ring to the right.
• The <INITIAL SET UP> menu will be displayed.
<INITIAL SET UP>
@TIME DATE ADJUST
HDD FULL
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
ARCHIVE DATA
MOTION DETECTION
LANGUAGE SELECTION
3. Turn the JOG dial move the cursor to ARCHIVE DATA. Turn
the SHUTTLE ring to the right.
• Turn the JOG dial to make the selection options flash.
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
@ARCHIVE DATA
4. Turn the JOG dial to make the "ALARM" option flash.Turn
the SHUTTLE ring to the right.
• The sub-item stops flashing.
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
@ARCHIVE DATA
5. Turn the SHUTTLE ring to the left or press the SET UP
button.
By turning the JOG dial, the sub-
item of ARCHIVE DATA shown on the menu will be
changed as follows:
"ALL": This backs up all the data recorded on the
main HDD after the ARCHIVE POINTER. Alterna-
tively, all data will be backed up.
"ALARM": Of all the data blocks recorded on the
main HDD(1 MB units), this will back up only the
data blocks that contain the alarm record. Some data
either side of the alarm record may be included when
backing up a small alarm record.
STOP
OFF
OFF
ALL
STOP
STOP
OFF
ON
ALL
OFF
STOP
OFF
OFF
ALL
STOP
OFF
ON
ALARM
31
Advertisement
Table of Contents
