Series Recording; Series Recording Menu Settings (For Both Units); Operation During Series Recording - Mitsubishi DX-TL1600EM Installation And Operation Manual

Series Recording

By connecting multiple units as show in the chart below
and selecting REC•STANDBY in the HDD Repeat Record-
ing setting, this unit can perform Series Recording. In Se-
ries Recording, when the first unit's hard disk has become
full, the second unit automatically begins recording.
System configuration (using two units)
First Unit
INFORMATION
hard disk reaches its maximum storage capacity,
the second unit will begin recording; when the sec-
ond unit's hard disk reaches its maximum storage
capacity, the first unit will begin recording by over-
writing its hard disk. If you do not want the first unit
to begin the over-writing process, then please you
don't connect the connection 1.
INFORMATION
minal, settings can be made so that a second unit
begins recording in the event that something goes
wrong with the recorder and it cannot continue re-
cording.
First Unit
Operation of
unit #1
Operation of
unit #2

Series Recording menu settings (for both units)

1. Press the SET UP button to display the <MENU SETTING>
menu.
2. Turn the JOG dial to move the cursor to the REAR TERMINAL
then turn the SHUTTLE ring to the right.
<REAR TERMINAL>
@MODE OUT
3. Turn the JOG dial to move the cursor to CAPACITY REMAIN
then turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<REAR TERMINAL>
@CAPACITY REMAIN
4. Check that the "HDD" is flashing. Turn the SHUTTLE ring to
the right.
• Choose the HDD so that the second unit begins recording
when the first unit's hard disk approaches its storage limit.
• The flashing will move to capacity setting.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
Second Unit
1
In this example, when the first unit's
Through use of the CALL OUT ter-
Second Unit
Something goes wrong with the recorder
Recording
Recording
REC
CAPACITY REMAIN HDD-10%
MODE OUT REC
HDD-10%
<REAR TERMINAL>
MODE OUT
@CAPACITY REMAIN
5. Turn the JOG dial till desired capacity remain appears and
then turn the SHUTTLE ring to the right.
• The sub-item will stop flashing.
<REAR TERMINAL>
MODE OUT
@CAPACITY REMAIN
6. Turn the JOG dial to move the cursor to MODE OUT and
turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<REAR TERMINAL>
@MODE OUT
CAPACITY REMAIN
7. Turn the JOG dial to flash "REMAIN"and turn the SHUTTLE
ring to the right.
• The sub-item will stop flashing.
<REAR TERMINAL>
@MODE OUT
CAPACITY REMAIN
8. Display the <INITIAL SET UP> menu.
• Press the SET UP button to display the <MENU SETTING>
menu. Move the cursor to INITIAL SET UP and turn the
SHUTTLE ring to the right.
<INITIAL SET UP>
@TIME DATE ADJUST
HDD FULL
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
ARCHIVE DATA
9. Turn the JOG dial to move the cursor to HDD FULL and
turn the SHUTTLE ring to the right.
• The sub-item will start flashing.
<INITIAL SET UP>
TIME DATE ADJUST
@HDD FULL
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
ARCHIVE DATA
10. Turn the JOG dial to display REC•STANDBY and turn the
SHUTTLE ring to the right.
• The sub-item will stop flashing.
<INITIAL SET UP>
TIME DATE ADJUST
@HDD FULL
HDD PB REPEAT
ARCHIVE OVERWRITE
AUTO EJECT
ARCHIVE DATA
11. Turn the SHUTTLE ring to the left or press the SET UP
button.

Operation during Series Recording

When the storage capacity of the first unit's HDD reaches
a pre-specified level, the second unit will begin recording.
Conversely, when the second unit's HDD capacity reaches
a pre-specified level, the first unit will begin recording.
Through this exchange, recording will continue uninter-
rupted.
Operation of
Recording
unit #1
Operation of
unit #2
REC
HDD-10%
REC
HDD-10%
REC
HDD-10%
REMAIN
HDD-10%
STOP
STOP
OFF
ON
ALL
STOP
STOP
OFF
ON
ALL
REC•STANDBY
STOP
OFF
ON
ALL
Overlapping period Overlapping period
Recording
Recording
55