System Output Timeouts (Addr 0710, 0712-0714); Download/Callback Opt. (Addr 1183, 0236-0255); Pager Format Options (Addr 0256 & 0257) - NAPCO Gemini GEM-P816 Programming Instructions Manual

!
Page 16
SYSTE M OUTPU T TI ME OUTS (AD DRESS 0710, 0712, 0713 & 0714)
ADDRESS 0710
PGM2
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
DATA DELAY/
ENTRIES TIMEOUT
blank (•) 0 min.
1 1 min.
2 2 min.
3 3 min.
4 4 min.
5 5 min.
6 6 min.
16 16 min.
255 255 min.
DOWNL OA D/CAL LB ACK OP TI ONS (ADDR ESS 1183 & 0236-0255)
ADDRESS 1183
No. Rings
Before
Pickup
[Default = 015 ]
Callback
0236 0237 0238 0239 0240 0241 0242 0243 0244 0245 0246 0247 0248 0249 0250 0251 0252 0253 0254 0255
Telephone
(Digits 1-20)
[Default = blank (•) for all digits 1-20]
CALLBACK TELEPHONE NUMBER: Enter telephone number to be used when downloading from a computer (see Glossary at
the back for more information).
!
1. Enter digit only.
!
2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).
!
3. Valid entries are: 1-9, B =
U D
!
4. Press or to save.
PAGER FOR MAT OP TION S (ADD RESS 0256 & 0257)
ADDRESS 0256
Leading Digits for
Pager Format
(1st Digit)
ADDRESS 0257
Leading Digits for
Pager Format
(2nd Digit)
[Default = blank (•) blank (•)]
X
GEM-P816 Programming Instructions
ADDRESS 0712
Alarm
Output
Timeout (min.)
[Default = 015]
!
1. Select delay/timeout (0-255 min.) from the table shown.
!
2. Enter in corresponding address locations above.
U D
!
3. Press or to save.
OUTPUT TIMEOUTS: If a timeout of "0 min." is selected, then the output will remain active (ON)
until the system is reset or disarmed. For UL Residential Installations, the minimum timeout is 4
minutes. Not UL listed for Commercial Installations.
NUMBER OF RINGS BEFORE PICKUP: Enter the number of rings before automatic
pickup by the control panel when downloading from a computer (see Glossary at the back
for more information).
!
1. Enter digit only.
!
2. Valid entries are: 03-15. NOTE: Default is 15 Rings.
U
!
3. Press or
ADDRESS 0236-0255 (RIGHT DIGITS 1-20)
* #
button, C = button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location.
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with "00".
However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows
you to program these digits to any number desired. A typical Pager report is "003 22 1234", where 3 is the Event,
22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as "98",
the Pager report will now appear as "983 22 1234". NOTE: See CS Receiver Options to select Pager Format.
!
1. Enter in 1st and 2nd Leading Digits as shown.
!
2. Valid entries are: 0-9. Press
ADDRESS 0713
Pulse Alarm
Output
Timeout (min.)
[Default = 015]
D
to save.
U D
or to save.
WI995C 2/04
ADDRESS 0714
PGM1
Output
Timeout (min.)
[Default = 0 min. = blank (•)]
L
NAPCO Security Systems