Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech B&B SmartWorx ESWGP506-2SFP-T
Summary of Contents for Advantech B&B SmartWorx ESWGP506-2SFP-T
- Page 1 ESWGP506‐2SFP‐T User Manual...
- Page 2 USA Headquarters Advantech B+B SmartWorx. 707 Dayton Road Ottawa, IL 61350 USA Phone (815) 433-5100 -- General Fax (815) 433-5105 Website: www.advantech-bb.com support@advantech-bb.com European Headquarters Advantech B+B SmartWorx Westlink Commercial Park Oranmore, Co. Galway, Ireland Phone +353 91-792444 -- Fax +353 91-792445...
-
Page 3: Table Of Contents
CONTENTS Figures ................................... 5 Tables ..................................... 7 Radio Frequency Interference Statement ........................8 Warranty ..................................9 Contents of Package ..............................10 Product Description ..............................11 Features ................................... 11 Hardware ..................................12 LED Description ................................ 12 MAX LED .................................. 12 PoE Reset ................................. 13 Front Panel ................................ - Page 4 Specifications ................................56 Certifications ................................57 Compliance and Disposal ............................. 58 Dimensional Drawing ..............................59 Advantech B+B SmartWorx Technical Support ......................60...
-
Page 5: Figures
FIGURES Figure 1. PoE DIP switch – Default setting shown (PoE enabled) ................13 Figure 2. Front Panel ..............................14 Figure 3. Triangle Mark ..............................17 Figure 4. LC Connector to the Transceiver........................17 Figure 5. Power Input Connections ..........................17 Figure 6. - Page 6 Figure 27. Dual Ring Configuration ..........................32 Figure 28. Redundancy Setting/RSTP .......................... 33 Figure 29. Port information ............................33 Figure 30. Port Configuration ............................34 Figure 31. VLAN Settings.............................. 36 Figure 32. Tag/Untag VLANs ............................37 Figure 33. 802.1Q VLAN settings ..........................37 Figure 34.
-
Page 7: Tables
Figure 54.Log Info ................................ 53 Figure 55. Firmware Update ............................54 Figure 56. Backup settings ............................55 Figure 57. Dimensional drawing ..........................59 TABLES Table 1. LED description .............................. 12 Table 2. Pin Assignments ............................. 16 Table 3. Port status ..............................26 Table 4. -
Page 8: Radio Frequency Interference Statement
RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 9: Warranty
Products of other manufacturers sold by Advantech B+B SmartWorx are not subject to any warranty or indemnity offered by Advantech B+B SmartWorx, but may be subject to the warranties of the other manufacturers. Power supplies are limited to a six year warranty. -
Page 10: Contents Of Package
• B+B Ethernet switch with attached DIN rail clip • Printed Quick Start Guide • 4-panel mounting clips with screws • RS-232 Serial Cable You may download the user manual at any time from the Advantech B+B SmartWorx web site: www.advantech-bb.com... -
Page 11: Product Description
PRODUCT DESCRIPTION The ESWGP506-2SFP-T is a plug-and-play, POE+, managed, industrial Ethernet Switches with IP30 protection. It provides four 10/100/1000Mbps copper ports and two SFP ports for 1000Mbps speed. The SFP port (Port #5) supports 10/100/1000 or 1000Mbps copper SFPs and gigabit fiber SFPs, for both Single-mode and Multi-mode fiber. -
Page 12: Hardware
HARDWARE LED DESCRIPTION Device Face Status Description PWR (P1, P2) Green ON Power applied to Port PWR (P1, P2) Green OFF No power to Port Green Flashing System is UP, passing data Green ON/OFF System is DOWN Console NO LED RJ-45 connection for a CLI using a hyperterminal prgm. -
Page 13: Poe Reset
POE RESET Figure 1. PoE DIP switch – Default setting shown (PoE enabled) There are two PoE DIP Switches. One is for a Hardware Reset (HW RESET). The other is for an Auto Reset (AUTO RESET). By default, PoE is set to ON, and supplying PoE, Power over Ethernet. Hardware Reset: When the DIP Switch #1 is set to the ON position, the PoE function will be turned off, and the power sourcing for a PD device is unavailable. -
Page 14: Front Panel
FRONT PANEL Figure 2. Front Panel... -
Page 15: Top Of Switch
TOP OF SWITCH Figure 3. Input TB DIN RAIL MOUNTING The DIN Rail mounting clips are connected to the switch when shipped and ready to be mounted on a 35mm size DIN Rail. Figure 4. Din Rail Mounting... -
Page 16: Panel Mounting
PANEL MOUNTING Figure 5. Panel Mounting RJ45 ETHERNET CONNECTION All copper ports on the switch support the Auto Cross feature, which allows the end user to use a straight through or crossover cable. The cabling should be CAT5e or greater for full throughput support. PIN ASSIGNMENTS PIN# Signal Direction PoE &... -
Page 17: Sfp Installation And Connection
SFP INSTALLATION AND CONNECTION To connect the transceiver and fiber cable, follow the steps below. The SFP port is not proprietary. Any MSA-compliant 1000Mbps fiber SFP can be installed in the port. (Note: SFP modules are typically terminated with an LC fiber connector). On port 5, the SFP port can accept both SERDES and SGMII copper SFP while Port 6 only supports SERDES copper SFP. -
Page 18: Software
SOFTWARE INITIAL SETUP / CONFIGURATION The ESWGP506-2SFP-T is a managed switch. There are three ways to configure the switch: through a Telnet mode, a console session, or a web browser. For a Telnet or Console session, connect an RJ-45 cable to the Console port, located on the front of the switch. -
Page 19: Figure 7. Console Mode
Figure 7. Console mode NOTE: 1. The supplied RS-232 cable must be used. Straight through or cross over cable will not work. 2. If the Console screen does not appear select Enter. 1. Using a VT100 Terminal emulation program (typically HyperTerminal in Windows) open the computer COM port connected to the switch (using supplied RS-232 cable). -
Page 20: Figure 8. Login Screen
Figure 8. Login screen The Console mode screen has four configuration options. 1. Overview 2. IP Settings 3. Factory Default 4. Logout Overview The Overview page displays the current switch IP address, MAC address, Firmware version, configured name, location, and description. •... -
Page 21: Figure 10. Ip Address, Subnet Mask, Default Gateway Settings
IP Settings The IP Settings page allows two methods of network address configuration, DHCP or Static. DHCP Setup • Use down arrow key to select IP Settings / select Enter • Select #1: Obtain IP address automatically (DHCP) / select Enter •... -
Page 22: Web Browser Configuration
Figure 12. Log out selection WEB BROWSER CONFIGURATION The Web Server provides a convenient way to configure the managed switch from a web browser. If you wish to use the web server management and monitoring functions from a host PC connected to the same LAN, they must be configured with the appropriate network settings. -
Page 23: Basic Settings
Figure 15. Overview page BASIC SETTINGS The following selections are available under Basic Settings: System Info Password Accessible IP Port Time System Information The System Information page allows the user to assign a unique name for the switch, the location of the switch, description of the switch, and contact name for the network administrator. -
Page 24: Figure 16. Custom Settings Options
Figure 16. Custom settings options Password Settings The Password Settings page allows up to three users to assign unique Users Names and Passwords. The User Index is used to select the individual users. Figure 17. Configuration for User Name, Password, and user index The maximum number of characters is 32 and a blank password can be configured. -
Page 25: Figure 18. Index/Ip Address Entries
Figure 18. Index/IP Address entries The web server connection, HTTP (Hypertext Transfer Protocol), is a communications protocol used to transfer or convey information on the Internet using default port 80. Https is a URL that implements a Secure HTTP connection using default port 443. All entered access IP Addresses must be a legal IP address. -
Page 26: Figure 19. Port Configuration Screen
Figure 19. Port Configuration screen Setting Description Default value Media Type The type of media, copper or fiber Copper or Fiber Mode Auto Negotiation or FORCE mode settings Auto-Negotiation Flow Control Managing data transmission of packets Enable MDI/MDIX Medium dependent interface of nodes Auto MDI/MDIX Enable Enable port configuration options... -
Page 27: Figure 20. Ip Settings: Dhcp Or Static
Figure 20. IP Settings: DHCP or Static Setting Description Default value DHCP/Fixed Network configuration Dynamic or Static IP IP Address The unique IP Address of the switch 192.168.118.100 Subnet Mask The range of logical addresses within the address 255.255.255.0 space Default The node that serves as an entrance to another 192.168.118.1... -
Page 28: Advanced Settings
Figure 21. Time Settings Setting Description Default value Local Time/NTP Time setting for switch system Local Time Time Zone Time Zone GMT-6 Daylight Savings Time Disable Date The format must be yyyy-mm-dd 2011-01-01 Time The format must be hh:mm:ss 00:00:00 Table 5. -
Page 29: Figure 22. Static Mode For Poe
The PoE management allows the monitoring and control of the PoE functions. An additional setting on the B+B switches is “Power Limit Mode”. In high temperature environments, the maximum power available to the switch can be set to “Dynamic mode”. In this mode, the switch uses the derating curve values of the external power source to reduce its power consumption requirement. -
Page 30: Port Priority
Static mode example: When the actual power of all connected PDs exceeds the “Power Supply Max(W)” the port with the lowest priority will be shut down. The “Power Supply MAX(W)” has a default of 120 but can be changed to the specific Watts of the power supply used. -
Page 31: Figure 24. Single Ring
Two types of RingOn configurations are available: Single loop and dual loop. Dual loop configuration connects two or more single loops. When configuring dual rings, unique ID's are used for each ring. Single Ring: Among several switches, the two ports of each switch will be connected with another switch. When building the single ring network, the two ports of one switch are first connected with the ports of another switch;... -
Page 32: Figure 26. Dual Ring
Figure 26. Dual Ring The web configuration screen shot illustrates the steps needed to implement a dual ring. Both ID 1 and 2 are enabled. Ports 1 and 2 connect single rings. Ports 3 and 4 connect the single rings together. Both rings are connected together using ID 4 coupling port. -
Page 33: Figure 28. Redundancy Setting/Rstp
Redundancy Setting: In the Advanced Settings category, the end user can select Port Configure and RSTP Information buttons to access sub-menus. Rapid Spanning Tree Protocol (RSTP) The Rapid Spanning Tree Protocol (RSTP) has evolved from the Spanning Tree Protocol (STP) to provide faster spanning tree convergence after a network topology change. -
Page 34: Figure 30. Port Configuration
Port Configuration • Port Number • Priority: (0 - 240) A method of prioritizing how ports are blocked. The value is configured in multiples of 16 with the highest value being blocked. • Path Cost: (1 - 200,000,000) RSTP method of ensuring that optimal paths will be selected after a link failure. - Page 35 VLAN 1 to access and manage the switch. VLAN 1 also allows the switch to operate as a standard switch. Every port must belong to a VLAN and ports may belong to more than one VLAN ID. Advantech B+B SmartWorx managed switches will support up to 26 port based VLAN groups.
-
Page 36: Figure 31. Vlan Settings
Figure 31. VLAN Settings 802.1Q VLAN Setup Advantech B+B SmartWorx managed switches also support IEEE 802.1q VLAN. Implemented 802.1q VLANs can extend over multiple switches. Switches can be from different manufactures as long as they support 802.1q A typical 802.1Q VLAN network and the web server configuration page can be found below. Note the difference between VLAN ID (frames that are tagged) and PVID (frame that are untagged). -
Page 37: Figure 32. Tag/Untag Vlans
Figure 32. Tag/Untag VLANs Figure 33. 802.1Q VLAN settings... -
Page 38: Figure 34. Trunking Settings
Trunking Trunking, sometimes called Link Aggregation, is a method of paralleling more multiple ports between two switches. The ability to configure this type of connection will increase the speed beyond the limits of a single port. The multiple links between switches can also act as a redundant path if one port loses communication. -
Page 39: Figure 35. Qos Settings
Figure 35. QoS settings 802.1p Priority The 802.1p header includes a three-bit field for prioritization, which allows packets to be grouped into various traffic classes. 802.1p traffic is simply classified and sent to the destination. • Choose Enable to start priority features based on 802.1p for each port. Figure 36. -
Page 40: Figure 37. Priority Settings
Figure 37. Priority settings DiffServ Priority DiffServ or Differentiated Services is a computer networking architecture that specifies scalable and coarse-grained mechanism for classifying, managing network traffic and providing quality of service (QoS) guarantees on modern IP networks. DiffServ can, for example, be used to provide low-latency, guaranteed service (GS) to critical network traffic such as voice or video while providing simple best- effort traffic guarantees to non-critical services such as web traffic or file transfers. -
Page 41: Figure 39. Dscp Settings
Once DiffServ Priority is selected, open the DSCP Priority Settings, which will allow a value (0-63) to be assigned to different queues. Figure 39. DSCP settings Setting Description Default value QoS enable Enable QoS function Disable Port-based QoS enable Enable Port-based QoS function Enable this group 802.1p QoS enable Enable 802.1p QoS function... -
Page 42: Figure 40. Igmp Settings
IGMP Snooping (Internet Group Management Protocol) IGMP Snooping provides a way to route multicast traffic and reduce unwanted traffic. IP multicasting is commonly used when sending the same information to many receivers. IGMP routes the multicast traffic to the correct devices and will not broadcast the message to unintended devices. IP multicast addresses are in the range of 224.0.0.0 through 239.255.255.255. -
Page 43: Figure 41. Broadcast Storm Protection
GMRP GMRP, GARP Multicast Registration Protocol, is a mechanism that allows bridges and switches to support a constrained multicast flooding of packets similar to IGMP snooping. It allows these devices to register and de-register attribute values, such as VLAN identifiers and multicast group membership. Broadcast Storm Protection Broadcast storm protection prevents network problems due to accidental network redundant loops reproducing broadcasts and multicasts. -
Page 44: Figure 42. Port Rate Settings
Destination Lookup Failure is also called DLF Message, which means that a packet type table does not match the MAC address table, and the message does not belong to broadcast or multi broadcast message. The switch handles such DLF messages the same way it handles the acceptance of broadcast messages. -
Page 45: Figure 43. Port Mirroring Settings
Port Mirroring Port mirroring is used on a network switch to monitor the network traffic of a specific port. The selected port's Ethernet traffic is duplicated and sent out a second specified port. This is commonly used with network monitoring hardware or software. Figure 43. -
Page 46: Figure 44. Static Mac Address Settings
Table configuration: • Select Add new Unicast or Multicast forwarding table • Add Static MAC Address to field • Select the desired port • Select add button Figure 44. Static MAC address settings Note: 1. Defined MAC addresses assigned port can be modified. 2. -
Page 47: Administration
ADMINISTRATION The simple network management protocol (SNMP) is used by network management systems to monitor network attached devices for conditions that warrant administrative attention. The SNMP V1/V2c/V3 are all supported by the switch. SNMP V1, and SNMP V2c use a community string match for authentication, which means that SNMP servers access all objects with read-only or read/write permissions using the community string public/private. -
Page 48: Figure 46. Network Client List
Diagnostics Scan Network and Ping are two diagnostic tools provided within the SNMP software. Scan Network will display a list of active network devices. The Ping function uses the PING command to give users a simple but powerful tool for troubleshooting network problems. Scan Network Scan Network will display IP address, MAC address, and its current status (active or Inactive). -
Page 49: Figure 48. Ping Test Results Example
Figure 48. PING Test results example Setting Description Default value Target IP IP address of device Blank Size Size of test (ping) packet Number The number of packet which will be sent Interval The interval time between ----- transmitted 1000 ping packets Timeout The no response timeout 5000... -
Page 50: Figure 49. Email Alert Settings
Alerts: Email Warning The Email Warning function allows e-mail alerts to be sent to defined users when port link (Up or Down) changes state, Relay Warning is enabled, Broadcast Storm events take place, and every 12 hours. The 12 hour report displays a log file of switch activities Figure 49. -
Page 51: Figure 50. Relay Warning
Relay Warning The managed switch has a relay output that can be used to signal the occurrence of one or more events when configured by the user. Figure 50. Relay Warning Performance Monitor Performance monitoring is available for each port and displayed on the webpage. The data is captured and will display the total number of events that have occurred since last power cycle. -
Page 52: Figure 52. Sort Function
MAC Address Table MAC (Media Access Control) address is a hardware address that network devices are assigned by the manufacturer. The managed switch provides an 8K MAC address table with automatic learning and aging. The MAC address table displays this table only if the network administrator is logged on. In the address table, the MAC addresses can be sorted by specified type. -
Page 53: Figure 53. Mac Address List
Figure 53. MAC address list Log Information The Log Info page will display the Index (event number), Date of event, Time of event, Type, and Event description. A total of 16 messages can be displayed on each page. Each available page is selectable using the Page drop down menu. -
Page 54: Figure 55. Firmware Update
System Update Firmware Update To keep your managed switch up to date with the latest firmware, a field upgrade procedure is available. Perform the following steps to upgrade the firmware: 1. Download the updated firmware (*.img) file and place in a folder. 2. -
Page 55: Figure 56. Backup Settings
Figure 56. Backup settings To restore a saved .cfg file select Browse and select the correct file. Next select the Upload button. When the transfer is complete the switch will restart. 1. Please use the extension file: *.cfg and ensure that the file is not altered. Altered files will fail during the CRC check sum operation during uploading. -
Page 56: Specifications
SPECIFICATIONS Technology Standard IEEE802.3, 802.3u, 802.3x, 802.3z, 802.3ab, 802.3af/at Processing Type Store and forward Broadcast Storm Disabled Flow Control Full Duplex Flow Control, Half Duplex Back Pressure Control Protocols CSMA/CD (Carrier Sense Multiple Access/Collision Detect) Switch Properties MAC Table Size Packet Buffer Size 128K Jumbo Frame Size... -
Page 57: Certifications
CERTIFICATIONS Certifications Safety IEC/UL/EN60950 FCC Part15, CISPR(EN55022) Class A CE EN61000-4-2 (ESD) CE EN61000-4-3 (RS) CE EN61000-4-4 (EFT) CE EN61000-4-5 (Surge) CE EN61000-4-6 (CS) CE EN61000-4-8 CE EN61000-4-11 CE EN61000-6-2 CE EN61000-6-4 Free Fall IEC60068-2-32 Shock IEC60068-2-27 Vibration IEC60068-2-6 UL/CUL Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. -
Page 58: Compliance And Disposal
COMPLIANCE AND DISPOSAL The products described here in comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (2006/95/EC). Will be certified for Information Technology Equipment including Electrical Business Equipment (Pending). European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. -
Page 59: Dimensional Drawing
DIMENSIONAL DRAWING Figure 57. Dimensional drawing... -
Page 60: Advantech B+B Smartworx Technical Support
ADVANTECH B+B SMARTWORX TECHNICAL SUPPORT Phone: 1-800-346-3119 (Monday - Friday, 7 a.m. to 5:30 p.m. CST) Fax: 815-433-5109 Email: support@advantech-bb.com Web: advantech-bb.com...