Blastrac BMG-435WD Operating Manual
Concrete floor grinder
Hide thumbs
Also See for BMG-435WD:
- Service manual (33 pages) ,
- Operating instructions manual (20 pages)
Table of Contents
Related Manuals for Blastrac BMG-435WD
Summary of Contents for Blastrac BMG-435WD
- Page 1 OPERATING MANUAL BMG-435WD VERSION 2.2...
-
Page 2: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY in accordance with Appendix II sub A of Directive 2006/42/EC BLASTRAC B.V. Utrechthaven 12 NL - 3433 PN NIEUWEGEIN Tel: 0031 (0)30 601 88 66 Fax: 0031 (0)30 601 83 33 Info@Blastrac.nl The Netherlands Declare under our sole responsibility that the machine as described below Conforms with the Health and Safety requirements of the European Directive of the machine Safety. -
Page 3: Table Of Contents
Table of contents EC Declaration of Conformity 1. Introduction 2. Machine description Application Accessories 3. Safety Safety precautions Safety regulations Safety instructions 4. Initial operation Checkpoints of electrical safety Checkpoints of machine safety Removing the diamond wings Mounting the diamond wings Diamag 5. -
Page 4: Introduction
The machine is simple to dismantle for ease of transportation. Due to the water hose connection, it is possible to grind wet. Application The BMG-435WD can be used on almost any floor to plane, to make ready for coatings, or to remove coatings or glue residues. Steer... -
Page 5: Safety
3. Safety Before operating the machine, the personnel who are going to use it must be familiar with the safety instructions given in this manual. Keep this manual near to the machine, so that it may be consulted. Safety precautions The surface to be treated must be swept clean to remove stones, screws etc. -
Page 6: Safety Instructions
Make sure the dust seal is in good condition, this to reduce the dust. Pull out the main plug when changing the diamond wings The BMG-435WD weights 115 kilogram. Use appropriate appliances as a lift or crane. Lift the machine with a rope on the frame (8) ... -
Page 7: Initial Operation
Because of the specially designed heat resistant magnets and fixation pins, the diamond tools are fixed onto the plate, but can still very simply be replaced by hand. Contact your Blastrac distributor for more information or check WWW.DIAMAG.EU... -
Page 8: Operating
5. Operating During operating the BMG-435WD, the following additional safety instructions must be followed closely. Switch on the machine Turn on the dust collector before switching on the machine and connect the dust hose to the machine. Connect the power supply to the machine (1) ... -
Page 9: Maintenance
Store the cleaned and dry machine in a dry and humid free room. Protect the electrical motor from moisture, heat, dust and shocks. All repair work must to be done by qualified Blastrac personnel, this to guarantee a safe and reliable machine. Any guarantee on the machine is automatically void when: Non original Blastrac parts and or diamond discs have been used ... -
Page 10: Technical Data
Dust hose 51 mm Ø 51 mm Ø 51 mm Ø 51 mm Ø connection Contact Blastrac BV Suitable filter unit We will assist you with a good advice Design and specifications are subject to change without notice by Blastrac BV... -
Page 11: Info@Blastrac.com.es
Headquarter Blastrac Poland Blastrac Italy Blastrac The Netherlands Golina, Dworcowa 47a S.S. 10 Padana Inferiore, 41 Utrechthaven 12 PL – 63-200 Jarocin IT – 29012 Caorso (PC) NL – 3433 PN Nieuwegein Tel – 0048 627 40 41 50 Tel – 0039 0523 81 42 41 Tel –...