Sony SR-R1 Operation Manual page 55

Using the Select FPS function
1
Connect the unit to the PMW-F3.
For details on the connection settings, refer to
the operation manual supplied with the PMW-
F3.
2
Make the system settings.
Select the target frame frequency (24, 25, or
30PsF) and recording format (4:2:2, 4:4:4
SQ, or 4:4:4 HQ).
For details, see "Formats available for Select
FPS shooting" (page 57).
Setting example: When setting the target
frame frequency to 24PsF (23.98PsF) and
recording format to 4:4:4 SQ
Display the SYSTEM Setup menu and then
1 select and confirm FORMAT t2 set
the format to match the system format of the
camera as shown below t3 move the
cursor to and confirm [SET].
1 FORMAT
S Y S T E M S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEYMAP
KEYINHI MAP
REMOTE/LOCAL
SERVO
REC INHI OFF
EDIT
POWER
BATTERY
OTHERS
S R - R 1 S T O P
The formats of the unit and camera are
switched, and "S59P(23PsF)" is displayed on
the display (for about 30 seconds).
dB
SDI SDI SDI SDI SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP EMP EMP EMP EMP
EE
L R L R L R L R L R L R L R
1 2 3 4 5 6 7
STBY OFF
TCG
01 01
H
ENCODE
16.5V REMAIN
SR-SQ
- - -
10bit
2 Set to match
the camera
Signal Format
LINE 1080P
FRAME 23.98
SIGNAL 444SQ
SELECT FPS ON
FPS FORMAT 59/60
[SET]
0 0 : 0 0 : 0 0 : 0 0
T C R
3 SET
SDI SDI SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R L R L R
8 9 10 11 12 13 14 15 16
SR-R1
KEYINHI
RECINHI
51 11
M S F
LOCAL
1920x1080
M 23PsF EE
4:4:4
17:11
The "S" in S59P indicates that SR Motion is
enabled (SELECT FPS is set to "ON"), and
the "59P" indicates that FPS FORMAT is set
to 59.94P. The "(23PsF)" indicates that the
target frame frequency is set to 23.98PsF.
To make the time code continuous
Make the following settings in the TC Setup
menu. (see page 37)
RUN MODE: R RUN (Rec Run)
TCG MODE: PRST (Preset)
3
Set the number of frames to shoot.
You can also set the number of frames to shoot
from the camera. For details, refer to the
operation manual supplied with the PMW-F3.
You can also change the number of frames to
shoot during recording. For details, see "Using
the Ramp function" (page 63).
If you press the SELECT/ENTER dial while
holding down the FUNC button, the
following screen appears, allowing you to
check the number of frames to shoot.
dB
SDI SDI SDI SDI SDI SDI SDI
0
-10
-20
SR Motion Recording
-30
-60
EMP EMP EMP EMP EMP EMP EMP
SYSTEM
EE
L R L R L R L R L R L R L R
SEL-FPS : 59.94P
1 2 3 4 5 6 7
MODE
SIGNAL
STBY OFF
MEMORY
TCG
48
01 01
H [ x 0.500 ]
ENCODE
16.5V REMAIN
SR-SQ
- - -
12bit
Playback speed
If you press the SELECT/ENTER dial or do
not touch it for 3 seconds, the display screen
returns to the state before you made the
setting.
If you display the screen above and then
press the SELECT/ENTER dial while
holding down the FUNC button again, the
following screen appears. If you press the
HOME button while holding down the
FUNC button in this state, the signal format
display at the bottom of the screen changes to
the SR Motion display, allowing you to
check the setting for the number of frames to
shoot.
SDI SDI SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP EMP EMP
: 23.98PsF
L R L R L R L R L R L R L R L R L R
8 9 10 11 12 13 14 15 16
: ON
: 0 FPS
SR-R1
: ---
KEYINHI
RECINHI
51 11
FPS
M S F
LOCAL
1980x1080
M EE
23PsF
4:4:4
17:11
Number of frames (FPS)
SR Motion 55