Related Manuals for Miele 06 868 521
Summary of Contents for Miele 06 868 521
- Page 1 Operating and Installation Instructions Commercial Dishwasher G 7856 en - US To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 06 868 521...
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 4 Guide to the machine ..........8 Description of the machine . -
Page 4: Important Safety Instructions
Do not install or use a damaged dishwasher. A damaged machine is dangerous. Unplug the machine and call your Miele dealer or the Miele Technical Service Department. - Page 5 If the power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. Do not use an extension cord to connect this machine to electricity. Extension cords do not guarantee the required safety of the machine (e.g.
- Page 6 Only use cleaning agents formulated for special processes and approved by Miele for use with this machine. Keep all cleaning agents out of the reach of children. Use of unsuitable cleaning agents could adversely affect the components of the machine.
- Page 7 Accessories Only specific additional equipment, made by Miele or approved by Miele, should be connected to this machine. Consult Miele on the type and application of such equipment. IMPORTANT SAFETY INSTRUCTIONS...
-
Page 8: Guide To The Machine
Guide to the machine a Connection for DOS unit G 60 Dosage pump for liquid detergents - optional (located on the rear side of the machine) b Filter combination c Salt reservoir (water softener) d Compartment for powder detergent e Rinse aid reservoir (with dosage selector) - Page 9 a On/Off button (I-0) b Door button c Display d Delay Start indicator (see "Programming special functions") e Extra drying indicator f Start indicator g Start button h Extra drying button i Display button to toggle between "Actual time" and "Elapsed wash time"...
-
Page 10: Description Of The Machine
Description of the machine This Miele machine is a commercial dishwasher with fresh water wash system and short batch times. It is especially suitable for use where quick turn-around flexible wash programs, and commercial durability are of the utmost importance. -
Page 11: Opening And Closing The Door
To open the door ^ Press the door button, hold the door grip and pull open the door at the same time. The door should only be opened during operation for emergencies, e.g. if items are knocking together or if a program fault is indicated in the display. -
Page 12: Water Softener
Water softener Water Softener To avoid the build-up of calcium deposits on items being cleaned and in the machine the water needs to be softened. To ensure a steady supply of soft water the water softener unit must always be: 1. - Page 13 Table of settings °d (German gr/gal scale) 19 *) °d Setting (German scale) *) factory setting Water softener gr/gal Setting...
-
Page 14: Filling The Salt Reservoir
Filling the salt reservoir Only special, coarse-grained reactivation salt* should be used in this machine. *Available from Miele. Please see back page for contact information. Do not use other types of salt, e.g. table salt, agricultural or gritting salt. These... -
Page 15: Salt Indicator
Water softener Salt indicator When the salt reservoir is empty the "Recharge" indicator, b, lights as a reminder to fill the reservoir. Reactivation takes place automatically during a program. The "Recharging" indicator, a, lights while this is occurring. -
Page 16: Rinse Aid
(liquid or powder detergent) will damage the reservoir! Only use rinse aid approved for this dishwasher. Adding rinse aid If the "Rinse aid" indicator lights, the rinse aid reservoir must be refilled. ^ Open the door fully. -
Page 17: Setting The Dosage
^ Add rinse aid until it is visible on the surface of the filter in the opening. ^ Close the flap until it clicks into place. Make sure it is firmly shut, otherwise water could get into the rinse aid reservoir during the program. -
Page 18: Loading The Machine
Loading the machine Loading the machine Preparation ^ Empty all containers before loading them into the machine. Ensure that no acid or solvent residues, especially hydrochloric acid or chlorides get into the wash cabinet. Notes ^ Load items so that water will come into contact with all surfaces. -
Page 19: Items Not Suitable For Dishwashers
^ Colors painted over a glaze may fade after a number of washes. ^ Clouding may occur on glasses after frequent washing. Our recommendations ^ Wash delicate glassware by hand. ^ Only wash dishwasher safe glassware, dishes and cutlery. -
Page 20: Upper Basket
Loading the machine Upper basket ^ Ideal for small, lightweight, delicate items such as cups, saucers, glasses, dessert bowls, etc. as well as lightweight heat resistant plastic items. Bottom basket ^ Ideal for larger and heavier items such as plates, serving platters, saucepans, bowls, etc. -
Page 21: Adjusting The Upper Basket
Adjusting the upper basket The upper basket can be adjusted above and below the middle position by 1" (2.5 cm). It is set in the middle position on delivery. Depending on the position of the upper basket, a variety of plate dimensions can be accommodated in the baskets. -
Page 22: Adding Cleaning Agent
Adding cleaning agent Only use cleaning agents formulated for this machine. Do not use detergents formulated for domestic dishwashers. Powder cleaning agent is dispensed via the compartment for powder cleaning agents in the door. Liquid cleaning agents are dispensed via the DOS-Module (available as an optional accessory). - Page 23 The DOS module comes with a separate Installation Manual. Adding cleaning agent Maintenance of the dispensing systems The following maintenance should be carried out by a Miele Service Technician to ensure trouble-free operation. Every 12-18 months: ^ Replace the dispensing hoses in the DOS module.
-
Page 24: Use
Turning on ^ Close the door. ^ Open the water supply (if closed). ^ Press the On / Off (I-0) button. If the program selector is turned to "Stop" a dot lights in the display. Starting a program ^ Turn the program selector clockwise or counterclockwise to the required program. -
Page 25: Selecting An Additional Function
Selecting an additional function "Extra drying" can be selected as an additional function. ^ Select the drying function directly after a program has been selected (not with "Rapid", "Rinse" and "Drain"). Drying is phased over 10 minutes. The total running time of the program lengthens accordingly. -
Page 26: Changing A Program
Changing a program If the "Start" button has not yet been pressed, the selected program can be changed. ^ Turn the program selector to the desired program. ^ If required select the additional function "Extra Drying" again. See "Selecting an additional function". ^ Press the "Start"... -
Page 27: Program Guide
Program For temperature sensitive glassware CHINA + and lightly soiled dishware. CRYSTAL Run-time: ~ 12 minutes* 120°F (plus 10 minutes for optional drying) Rapid program for continuously used RAPID dishes.**) 130°F Powder detergent: Place detergent directly on the right hand side of the door interior, NOT in the detergent cup. - Page 28 Program guide Program For normally soiled items. NORMAL Run-time: ~ 24 minutes* 130°F (plus 10 minutes for optional drying) For normally soiled items. Higher wash NORMAL temperature to remove starchy foods. PLUS Run-time: ~ 25 minutes* 140°F (plus 10 minutes for optional drying) For heavily soiled items.
-
Page 29: Programming Special Functions
Every change of the factory setting should be documented in case of possible technical service. Record any changes in the field "Adjusted value___________". 1. Setting the cold water inlet from: "Nominal water intake" to "Nominal water intake + 1 l". The amount of water taken into the machine at each intake can be increased by 1 liter to a maximum of... - Page 30 Programming special functions 3. Selecting an economy interim rinse (only for "Rapid" program) ^ Turn the program selector to "STOP". ^ Turn the machine off. ^ Press and hold the "Display" and "Start" buttons, at the same time turn the machine on with the "On / Off" button.
- Page 31 Setting the dosage Set the dispensing amount according to the detergent manufacturer's recommendations and the applications. The machine needs 7 liters of water in the program cycle "Main wash". Example: The detergent manufacturer recommends 4 ml of detergent per liter water.
- Page 32 Programming special functions 5. Altering the cleaning temperature and/or the temperature holding time in the "Main Wash" and "Final rinse"stage of the program cycle Any changes to the wash temperature and/or the temperature holding time should be recorded in the program chart. The main wash and final rinse temperatures can be changed from 86°F - 158°F (30 °C - 70 °C) and the...
- Page 33 ^ Temperature "Final rinse": Turn the program selector to the "STOP" position (the programming level is displayed in this position only). ^ Press "Extra Drying" again. "E05" (programming level 5) is displayed field. ^ Turn the program selector to the program to be changed.
- Page 34 Programming special functions 6. Delay start and setting the delay start time The start of a wash program can be delayed up to 9 hours and 30 minutes in 30 minute increments. Delay start should only be selected with the "Normal" and "Intensive" programs. The short programs cannot guarantee satisfying cleaning results when the residues are allowed to dry on because...
- Page 35 7. Buzzer A buzzer (30 secs) can be set for the following functions: – End of program = Buzzer constantly – Error = Buzzer sounds every other second ^ Turn the program selector to "STOP". ^ Turn the machine off. ^ Press and hold the "Display"...
- Page 36 Programming special functions 8. Re-setting all changes back to the factory default ^ Turn the program selector to "STOP". ^ Turn the machine off. ^ Press and hold the "Display" and "Start" buttons, at the same time turn the machine on with the"On / Off" button.
-
Page 37: Machine Care
Filter combination The machine must not be used without all filters in place. The filters protect the circulation pump from damage caused by foreign objects. The filter combination in the base of the wash cabinet should be inspected regularly and cleaned if necessary. - Page 38 Machine care Cleaning the spray arms From time to time, particles may become trapped in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. Remove the spray arms as follows: ^ Unscrew the upper spray arm. ^ Unscrew the middle spray arm (under the upper basket) clockwise at the knurled nut.
- Page 39 Cleaning the non-return valve and drain pump If water has not been pumped away at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the washer. ^ Remove the filter combination from the wash cabinet.
-
Page 40: Cleaning The Filters In The Water Inlet
Machine care Cleaning the filters in the water inlet Filters are incorporated in the screw connection of the water inlet hose to protect the water inlet valve. If these filters become dirty they need to be cleaned, otherwise insufficient water flows into the wash cabinet. -
Page 41: Correcting Minor Faults
With the aid of the following notes, minor faults can be corrected without contacting the Miele Service Department. Any work on the electrical components of the machine should only be carried out by a qualified and trained person in accordance with local and national safety regulations. - Page 42 ^ Take off the service panel (see "Electrical connection"). ^ Press the reset button on the heater limiter (yellow) located on the left- hand side of the plastic cover. If this switch trips again, please contact the Miele Technical Service Department.
-
Page 43: After Sales Service
In the event of a fault which you cannot correct yourself or if the fault code "F..." shows in the display please contact the Miele Service Department at the phone number on the back of these instructions. ^ Please quote the model and serial number of your machine. -
Page 45: Installation Instructions
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use. -
Page 46: Caring For The Environment
Caring for the environment Disposal of the packing material The protective packing materials are environmentally safe and can be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of the appliance Appliances contain materials which can be recycled. -
Page 47: Installation
Please refer to the installation diagram supplied with the machine. Furniture and fittings installed near the machine must be of a commercial standard, able to withstand the effects of steam and condensed water. Installation options – Free-standing – Undercounter The machine should be positioned under a continuous worktop or sink drainer. -
Page 48: Leveling The Machine
Please refer to installation directions included with the toe kick. Depending on the requirements for installation, the following "kits" can be ordered from the Miele. Cover plate (protects the countertop) The underside of the countertop is protected from steam damage by a... -
Page 49: Electrical Connection
A damaged power cord must only be replaced with a genuine Miele cord by a Miele Service Technician. ^ For technical data see the data plate or wiring diagram supplied. - Page 50 Electrical connection Removing the service panel and the protective plastic cover Isolate the machine from the power supply. ^ Holding the service panel on both sides, pull gently outwards from beneath, a, and remove it, b. ^ Remove the protective plastic cover and unscrew the 2 screws (left and right), c.
-
Page 51: Plumbing
7.25 - 145 psi the "Fill/Drain" indicator may come on and the fault code "F2 E" will show in the display. Please contact the Miele Service Department. ^ The machine is supplied as standard for connection to a cold (coded blue) and a hot (coded red) water supply up to a max. - Page 52 Hose clamps are supplied for securing it in position. ^ A longer drain hose (up to 13 ft. [4 m] long) is available to order from Miele. ^ The drainage system must not exceed 13 ft. (4 meters).
-
Page 53: Technical Data
Height: Width: Depth: Voltage: Rate load: Fuse rating: Connection cable: Water pressure (flow pressure): Cold or hot water connection: Drainage length: Delivery head: Inlet hose: Drain hose: Noise level in dB (A): English ½ " (32 ") " " see data plate see data plate see data plate approx. - Page 56 All rights reserved / 3807 M.-Nr. 06 868 521 / 00...