Table of Contents
Advertisement
Quick Links
GENUINE SATELLITE RADIO KIT
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the satellite
radio kit. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
• There are several
safety when installing. Always read and follow them in order to prevent injuries,
accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if the
warning is ignored.
CAUTION:
Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
• If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.
• If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.
• Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.
•
To ensure safety and reliability of the work, installation, removal and disposal work
done by an Authorized Mazda Dealership is recommended.
•
Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.
PART NAME:
PART NUMBER:
VEHICLE:
Note
To the dealer
• Please turn over these instructions to the customer after installation.
To the customer
• Keep these instructions after installation. The instructions may be necessary for
installing other optional parts or removal of this accessory.
•
Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.
WARNING
WARNING and
CAUTION sections in this booklet concerning
SATELLITE RADIO KIT
0000 81 M09 (Harness Kit H5)
Mazda CX-7
Mazda CX-7－1
1ED6P11A22600
Advertisement
Table of Contents
Related Manuals for Mazda 0000 81 M09
Summary of Contents for Mazda 0000 81 M09
-
Page 1: Installation Instructions
Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored. • If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. -
Page 2: Antenna Cable
(Harness (H5)) SIRIUS only To AUX or Bluetooth H/F Electro tap Electro tap 【CAN (+) and CAN (-)】 【+B and ACC】 DLP unit Antenna cable Tie redundant part Harness (H5) (Harness (H5)) To Audio unit Mazda CX-7－2... -
Page 3: Connection Diagram
To AUX or Bluetooth H/F 16 pin connector CONNECT (Gray) DLP unit (SIRIUS) Antenna cable CAUTION • When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle. Mazda CX-7－3... - Page 4 16 pin connector 8 pin connector CONNECT (Gray) DLP unit (SIRIUS) Antenna cable CAUTION • When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle. Mazda CX-7－4...
-
Page 5: Table Of Contents
Part Part name Qty. Part Part name Qty. Antenna DLP unit Alcohol wipe NOT SERVICED 0000-81-L17 ORDER Z40 KIT Harness Kit H5 (0000 81 M09) Part Part name Qty. Part Part name Qty. Part Part name Qty. Double-sided Harness (H5) - Page 6 20 {0.78} mm {in} Note • When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory. Mazda CX-7－6...
- Page 7 2. Pull the front side trim in the direction shown by the arrow, then detach clip A. Vehicle front Console panel (driver’s and passenger’s side) removal 1. Remove clips A in order starting from the vehicle rear using a tape-wrapped flathead screwdriver. Clip A Console panel Vehicle front Mazda CX-7－7...
- Page 8 1. Press the stay damper in the direction shown by the arrow and detach it from the glove compartment lid. 2. Bend the stoppers inward to remove. 3. Turn the glove compartment downward and pull the pins. 4. Remove the glove compartment. Stay damper Glove compartment Vehicle front Mazda CX-7－8...
- Page 9 (See hood release lever removal note on page 10.) 5. Remove the screw. 6. Pull the lower panel outward and detach clips A. Clip A 7. Disconnect the connectors, then remove the lower panel. Lower panel Screw Vehicle front Hood release lever Mazda CX-7－9...
- Page 10 2. Remove the decoration panel. Clip A Decoration panel Center panel removal Center panel 1. Remove the screws. Flathead screwdriver Vehicle front 2. Pull the center panel outward and detach clips A. 3. Remove the center panel. Clip A Screws Mazda CX-7－10...
- Page 11 1. Pull the upper column cover upward and detach the upper column cover from the lower column cover. Clip A 2. Pull the meter hood and remove clips A and tabs B. 3. Remove the meter hood. Tab B Vehicle front Upper column cover Mazda CX-7－11...
- Page 12 1. Partially peel back the seaming welt. 2. Pull the B-pillar lower trim outward and detach clips A, C Locator pin B and locator pins B. 3. Remove the B-pillar lower trim. Vehicle front Clip C Clip C detail Mazda CX-7－12...
- Page 13 2. Pull the trunk end trim upward, then disengage tabs A, clips B and pins C. 3. Remove the tabs D. 4. Remove the trunk end trim. Vehicle front Fastener Trunk side trim Tab A Clip B Pin C Mazda CX-7－13...
- Page 14 N･m {kgf･cm, in･lbf} Rear combination light (passenger’s side) removal Nut: 4.1－6.1 {42－62, 37－53} 1. Disconnect the connectors. 2. Remove the nuts using 10 mm socket. Connector 3. Remove the rear combination light. Vehicle front Rear combination light N･m {kgf･cm, in･lbf} Mazda CX-7－14...
- Page 15 Pad protector Pad protectors DLP unit 3. Affix pad protectors to the DLP unit as shown in the figure. Double-sided adhesive tapes 4. Adhere double-sided adhesive tapes to the top of the pad protectors. Pad protectors DLP unit Mazda CX-7－15...
- Page 16 7. Install the DLP unit to the dashboard member and secure Dashboard member with tie wraps (large). DLP unit CAUTION • To ensure proper affixing, be sure to degrease the area where the pad protector is affixed. Tie wraps (large) Vehicle front Mazda CX-7－16...
-
Page 17: Antenna
4. Install the antenna in the position shown in the figure. Roof CAUTION Vehicle front • To ensure proper affixing, be sure to degrease the Antenna area where the double-sided adhesive tape is affixed. 90 {3.54} 15－20 {0.59－0.78} mm {in} Mazda CX-7－17... - Page 18 Butyl tape Antenna cable metal as shown. • To trunk compartment Take care not to trap antenna cable under attachment Antenna cable nuts. Ⓑ 20 {0.78} 60 {2.36} 30 {1.18} Vehicle front Seaming Pad protector 1/2 mm {in} welt Mazda CX-7－18...
-
Page 19: Tie Wrap (Large)
Tie wrap Tie wrap (small) (large) Vehicle front Ⓔ 4. Route the antenna cable through the inside of the front Ⓔ Antenna cable scuff plate inner and secure it with tie wraps (large). Vehicle front Ⓕ Tie wraps (large) Mazda CX-7－19... - Page 20 Note • Bundle the antenna cable into a loop and attach it to Ⓖ the sheet metal on the inside of the trunk side trim, Pad protector and secure with pad protectors. Tie wrap (small) Tie wraps (large) Mazda CX-7－20...
-
Page 21: Double-Sided
Not used 100 {3.93} Note • The leftover pad protector is not used. 4. Adhere the pad protector to the top of the double-sided {1.96} adhesive tape. {0.86} mm {in} Double-sided Pad protector adhesive tapes iPod integration module Mazda CX-7－21... - Page 22 7. Fold back the iPod connection cable and affix it to the Pad protector Dashboard dashboard with a pad protector. CAUTION • To ensure proper affixing, be sure to degrease the area where the pad protector is affixed. Selector lever Vehicle front iPod connection cable Mazda CX-7－22...
- Page 23 (See step 6 on page 16 as to the installation position.) 7. Bundle the harness (H5) and antenna cable using a tie wrap (large) as shown in the figure. Harness (H5) DLP unit Vehicle front Tie wrap (large) ⓐ Mazda CX-7－23...
-
Page 24: Pad Protector
Audio 24 pin connector 13. Secure the harness (H5) +B, ACC wires to the vehicle [Audio 24 pin connector] wiring harness with tie wrap (large). Terminal B: +B (Orange) Kit wire: +B (Yellow) Terminal R: ACC (Blue) Kit wire: ACC (Red) Mazda CX-7－24... -
Page 25: Tie Wrap (Small)
19. Secure the harness (H5) CAN (+, -) wires (for Sirius and for iPod) to the vehicle wiring harness with tie wrap (small). Terminal X: CAN (-) (Dark blue/Red) Kit wire: CAN (-) (Black) Mazda CX-7－25... - Page 26 Tie wrap (large) Antenna cable ⓔ Tie redundant part Vehicle front Remove connector cover when connecting iPod; fit connector cover when iPod is not used Put iPod connection cable in glove box (Cable 300 {11.81} from dashboard member) mm {in} Mazda CX-7－26...
- Page 27 6. Wrap the cut harness tube and the vehicle wiring harness harness) with vinyl tape. 7. Wrap the cut harness tube and the AUX or Bluetooth H/F 50 {1.96} connector harness with vinyl tape. Vinyl tape mm {in} Mazda CX-7－27...
- Page 28 14. Wrap the electro taps and vehicle wiring harness together using urethane. 15. Secure the harness (H5) +B, ACC wires to the vehicle wiring harness with a tie wrap Terminal R: ACC (Blue) Kit wire: ACC (Red) (small). Mazda CX-7－28...
- Page 29 21. Secure the harness (H5) CAN (+, -) wires (for Sirius) to the vehicle wiring harness with tie wrap (small). Terminal V: CAN (+) (Gray/Red) Kit wire: CAN (+) (Red) Terminal X: CAN (-) (Dark blue/Red) Kit wire: CAN (-) (Black) Mazda CX-7－29...
- Page 30 25. Tighten the harness (H5) GND wire using the vehicle bolt. Audio 24-pin connector • Bolt tightening torque: Hazard switch connector 6.9 – 9.8 N･m {71.0 – 99.0 kgf･cm・61.0 – 86.0 in･lbf } Bolt Harness (H5) Audio unit GND wire Screws Screws Vehicle front Mazda CX-7－30...
- Page 31 If the TCS/DSC or DSC OFF indicator lights do not turn off after turning the ignition switch to the ON position, consult your Mazda dealer. • When the battery is disconnected, the windows will not fully open and close automatically.
- Page 32 Note: Sirius broadcasts can only be received in an open area, enclosed spaces such as garages or work buildings block the satellite reception. To troubleshoot problems, go to the following web page and select “Troubleshooting” in the Satellite Radio section: https://portal.mazdausa.com/dealershome/service_parts/accy_website/CX7_ACCY_HOME.htm Date Vehicle. VIN. The term of validity for this sheet: 12 months Mazda CX-7－32...