Barbecook Brahma 4.2 Installation Instructions Manual page 30

Note: the regulator may differ from the
version shown here.
PRIOR TO FIRST USE / AFTER
PROLONGED PERIOD OF NON-USE
Do not use the barbecue before you have
read, understood and checked all informa-
tion in this manual.
Ensure that:
• The barbecue is correctly installed
• There is no leak in the gas supply
(see 'Leakage test')
• The burners are correctly installed,
the venturi tubes are properly placed
over the openings of the gas valves
(Fig. D), and there are no obstruc-
tions (see safety information and
cleaning of the burners)
• None of the gas supply hoses can
come into contact with a hot surface
• Your barbecue is installed in a safe
place
D
SAFETY INFORMATION
Natural hazards - spiders and insects:
very tiny insects may crawl into the ven-
turi tubes of the gas burners and build a
web or nest (Fig. E)
E
that could block gas flow in whole or in
part. Such a situation is indicated by a
smoky, yellow flame and/or burner that
can only be lighted with difficulty or not
at all. The gas may eventually burn
outside the venturi tube and thus cause
serious damage to your barbecue.
Should this happen, immediately close
the cylinder. Clean the burners as soon
as the barbecue has cooled down.
Remove the burner(s) as shown in Fig.
F. Clean with a pipe cleaner or brush
both venturi tubes. Put the burner
back into place in accordance with the
instructions. (Fig. F) After cleaning, the
venturi tubes must be correctly placed
back over the openings of the gas
valves.
Note: damage arising from a fully or partly
blocked venturi tube in a burner is not cov-
ered by the guarantee and is considered
lack of proper maintenance
30 www.barbecook.com
F
.
LIGHTING THE BURNERS
Prior to lighting the burners, all checks and
procedures detailed in the chapter 'Before
the first use' must have been carried out.
• The lid of the barbecue must always
be open when you light the burner(s)
• Do not bend directly over the barbe-
cue when lighting the burner(s)
• The control knobs of the barbecue
must be 'OFF'. Slowly open the gas
cylinder valve. Before opening the
control knob of one burner, wait ap-
prox. 10 seconds to allow to gas to
stabilize
• Important: first light the middle bur-
ner
• As soon as one burner has been
lighted, you only need to put the
control knob of the other burner(s) in
the position 'HIGH' to light them.
• Never try to light all burners at once
LIGHTING THE BURNERS WITH THE
IGNITER
• Open the lid of the barbecue
• Open the gas cylinder valve.
• Press the igniter until you hear
sparks
• Holding down the igniter, press the
control knob of the middle burner
and turn to 'HIGH'
• If the burner does not light after 3
attempts, disconnect the gas and
wait 5 minutes before trying again.
This will allow the accumulated gas
to escape. Try again, repeating the
above steps.
• If the burner still does not light, read
the chapter 'Troubleshooting Guide'
to determine the cause and the
remedy, or use a match as described
below.
G
LIGHTING THE BURNERS WITH A
MATCH
Left and right at the bottom of the burner
box is a small opening that can be used
to light the burners with a match, if the
electronic igniter does not work. (Fig. G)
• Open the lid of the barbecue
• Place a match in the match holder
provided (Fig. G)
• Hold a burning match through
the hole, approx. 13 mm from the
burner
• Open the gas cylinder valve.
• Push the required control knob
and turn to 'HIGH'. The burner
should light within 5 seconds. If
not, turn the control knob off and
wait 5 minutes to allow the gas to
escape.
• Repeat steps 1 through 5. If the
burner still does not light after 3
attempts, read the chapter 'Trou-
bleshooting Guide'
LIGHTING THE OTHER BURNERS
• As soon as the middle burner has
been lighted, you only need to
put the control knob of the other
burner(s) in the position 'HIGH' to
light them.
LIGHTING THE SIDE BURNER USING
THE IGNITER
Only for Brahma 5.2 –4.0
223.9952.000 – 223.9952.200 -
223.9940.000 - 223.9940.200
First open the lid of the side burner.
To light the side burner, use the igniter
on the control panel and the control knob
on the side table.
• Press the igniter until you hear
sparks.
• Holding down the igniter, press
the control knob of the side burner
and turn to 'HIGH'
• Repeat a number of times if the
burner does not light immediately.
• If the burner does not light after 5
seconds, turn the control knob to