Download Print this page

EPV PowerMax Tension Series User Manual

Electric motorized projection screen

Advertisement

Quick Links

Electric Motorized Projection Screen
PowerMax Tension Series
Important Safety & Warning Precautions
Make sure to read this user's guide and follow the procedures below.
Caution: The screen's Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved
changes or modifications (except for cutting the power cord for hardwire installations) to this unit are
prohibited and will void your warranty. For more information, please contact our Technical Support
Department at (877) 511-1211 Ext. 604.
Please retain this user's guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
Never overload the power cord to prevent an electric shock or fire due to a loose contact or a
short circuit.
There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by
yourself. No one except authorized technicians can open and make repairs to this unit.
Make sure the power source this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Rev.051313-JA
User's Guide
1
www.elitescreens.com/epv

Advertisement

loading
Need help?

Need help?

Do you have a question about the PowerMax Tension Series and is the answer not in the manual?

Questions and answers

Summary of Contents for EPV PowerMax Tension Series

  • Page 1 Electric Motorized Projection Screen PowerMax Tension Series User’s Guide Important Safety & Warning Precautions Make sure to read this user’s guide and follow the procedures below. Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller.
  • Page 2: Pre-Installation

    Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure that the fasteners used are of adequate strength and suitable for the installation location. Rev.051313-JA www.elitescreens.com/epv...
  • Page 3 Accessories for PowerMax Tension Series In-wall RJ45 module 3 way wall switch Bubble leveler Hardware Parts List for PowerMax Tension Series Hardware Parts List a. Mounting Bracket b. M4x50 Screw c. M10 Anchor d. Suspended Ceiling Bracket Connector e. M5x15 Screw& Bolt Flush Mount to the Wall 1.
  • Page 4 1. Mark the location of where the screen is to be installed, drill your holes and insert the M10Anchors (c). 2. Install the Mounting Brackets (a) to the ceiling and secure with the M4x50 Screws (b). Ceiling M10 Anchor Mounting Bracket Fix Plate 1 Mounting Bracket M4x50 Screw Mounting Bracket Fix Plate 2 Rev.051313-JA www.elitescreens.com/epv...
  • Page 5 3. Insert chains (not included) through the loop holes of the Suspended Ceiling Bracket Connector (d). Suspended Ceiling Bracket Connector Loop Holes Screen removal from the Mounting Brackets 1. Pull down on the Mounting Bracket Release Tab and remove the bottom case away from the wall/ceiling followed by the top of the case. Rev.051313-JA www.elitescreens.com/epv...
  • Page 6 Push Tension Knob Control System for PowerMax Tension Series 3 Prong Power Cable 1. 5-12V Trigger: The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down.
  • Page 7 3. After testing the connection, place the in-wall switch module in/on the wall and wire the Ethernet cable into the wall and complete the setup. For more information, technical support or your local Elite Screens contact, please visit www.elitescreens.com Rev.051313-JA www.elitescreens.com/epv...