[Lamp Relay] - Panasonic PT-DZ21KU Operating Instructions Manual

[PROJECTOR SETUP] menu
[L1] Lamp 1 will light.
[L2] Lamp 2 will light.
[L3] Lamp 3 will light.
[L4] Lamp 4 will light.
[L1/L4] Lamp 1 and Lamp 4 will light.
[L2/L3] Lamp 2 and Lamp 3 will light.
[L1/L2/L3] Lamp 1, Lamp 2 and Lamp 3 will light.
[L1/L2/L4] Lamp 1, Lamp 2 and Lamp 4 will light.
[L1/L3/L4] Lamp 1, Lamp 3 and Lamp 4 will light.
[L2/L3/L4] Lamp 2, Lamp 3 and Lamp 4 will light.
[SINGLE] One lamp will light. (A short usage
(1 lit) time lamp will automatically light.)
[DUAL] Two lamps will light. (A short usage
(2 lit) time lamp will automatically light.)
[TRIPLE] Three lamps will light. (A short usage
(3 lit) time lamp will automatically light.)
[QUAD]
Four lamps will light.
(4 lit)
3) Press the <ENTER> button.
Note
z For a set time after [LAMP SELECT] is switched,
[LAMP SELECT] cannot be switched again,
because the speed of the lamp replacement cycle
will increase. Repeatedly switching [LAMP SELECT]
in a short time will also increase the speed of the
lamp replacement cycle.
z The colors of the items indicate the status.
Green → Current setting
Yellow → Current setting
(When there is a lamp that cannot turn on or failed
to turn on)
Red → Lamp that has failed to turn on
White → Any other status
z When a lamp fails to turn on or has been used in
excess of 2 000 hours
[QUAD] is selected, that lamp is turned off and
another lamp turned on.
When a lamp fails to turn on or has been used in
excess of 2 000 hours
not been used in excess of 2 000 hours
on.
The projector enters standby mode when all lamps
have been used in excess of 2 000 hours
z Ensure that lamp units not to be turned on are also
installed.
z More lamps than the specified number of lamps
light temporarily to prevent decreased illuminance
when a lamp is switched.
*1: 500 hours when the optional accessory replacement lamp
unit (for portrait mode) (Model No.: ET-LAD510P (1 pc),
ET-LAD510PF (4 pcs)) is used.
104 - ENGLISH
*1 and a setting other than
in [QUAD], a lamp that has
*1
*1 is turned
.
*1

[LAMP RELAY]

The lump to be turned on can be automatically
switched by setting a day and time.
The degradation of the lamp due to continuous usage
can be reduced by automatically switching the lamp
to be turned on when using the projector continuously
for a week or more.
1) Press ▲▼ to select [LAMP RELAY].
2) Press ◀▶ to switch [LAMP RELAY].
▶
z The time setting to switch the lamp will change
as follows each time you press the button.
[OFF] [24H]
3) Press ▲▼ to select [TIME].
4) Press the <ENTER> button.
▶
z Enters adjustment mode (the display is
blinking).
5) Press ◀▶ to select [HOUR] or
[MINUTE], and then press ▲▼ to
adjust it.
(1 hour or 1 minute increments)
[00:00] [00:01]
6) Press the <ENTER> button.
▶
z The adjusted time is established.
7) Press ▲▼ to select [DAY OF THE
WEEK].
8) Press ◀▶ to switch [DAY OF THE
WEEK].
▶
z The setting will change as follows each time
you press the button.
[SUNDAY] [MONDAY]
[SATURDAY] [FRIDAY]
Note
z The [LAMP RELAY] function is enabled when
[SINGLE], [DUAL], [TRIPLE], or [QUAD] is selected
in [LAMP SELECT].
z When [SINGLE] or [DUAL] is selected in [LAMP
SELECT], the lamp switches to the specified time.
When [TRIPLE] is selected in [LAMP SELECT], the
lamp switches a total of three times every two hours
from the specified time, and thereafter maintains
the previous status until the specified time.
When [QUAD] is selected in [LAMP SELECT],
three turn on at the specified time and the three
lamps switch every two hours for a total of four
[1WEEK]
[00:59]
[TUESDAY]
[WEDNESDAY]
[THURSDAY]