Advertisement
Quick Links
INSTRUCTIONS-PARTS LIST
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
Series 1200 and Series 2000
Turbine Sprayers
110/120V 50/60 Hz
6.0 psi (0.41 bar)
Model M73378
Complete Series 1200 Turbine, with hose and turbine gun
Model M73380
Basic Series 1200 Turbine, without hose or gun
Model M73428
Complete Series 2000 Turbine, with hose and turbine gun
Model M73432
Basic Series 2000 Turbine, without hose or gun
Series 1200
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
03018A
ECOPYRIGHT 1994, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
308423
Rev. C
03019A
Series 2000
Advertisement
Related Manuals for Graco M73380
Summary of Contents for Graco M73380
- Page 1 Complete Series 2000 Turbine, with hose and turbine gun Model M73432 Basic Series 2000 Turbine, without hose or gun 03019A Series 1200 Series 2000 03018A GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 ECOPYRIGHT 1994, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001...
- Page 2 Table of Contents Symbols Warning Symbol Warnings ........General Information .
- Page 3 D Do not use hoses to pull equipment. D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F). D Wear hearing protection when operating this equipment.
- Page 4 WARNING TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed. D Know the specific hazards of the fluid you are using. D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.
-
Page 5: General Information
The contents of the Series 2000 Turbine Sprayer, spray gun. Model M73428, includes: 1 Series 2000 Turbine Sprayer, M73305 Unpack the Graco Turbine Sprayer from the shipping 1 Turbine Gun, M73200 carton and inspect for any possible shipping damage. 1 25 ft. hose, M71452 If necessary, call the Customer Service toll–free num-... - Page 6 Setup NOTE: Refer to the turbine gun manual, 308–336, for NOTES: information on the operation and setup of the gun. D The circled letters in Fig. 1 indicate hose line con- Connect the Fluid and Air Supply nections. D The Series1200 and Series 2000 turbine units 1.
- Page 7 Setup Prepare the Fluid 1. Always strain the fluid before spraying; this includes color, reducer and hardeners if used. 2. When using a turbine spray system, you need to use a slower drying reducer or thinner to compen- 02845 sate for the faster drying time caused by the warm Fig.
- Page 8 Setup 1. Turn the turbine on a few minutes before you start CAUTION spraying to allow for warm-up time. Turn the turbine off when it is not in use; it does not shut off If the 2 quart remote pressure pot is accidentally automatically.
- Page 9 Shutdown Pressure Relief Procedure b. 2 1/2 Gallon Remote Pot: Pull the pressure relief valve ring (206c) until pressure is com- pletely relieved. 2 Quart Remote Pot: Turn out the pressure WARNING relief knob (113) about one turn. Wait until pressure is completely relieved before remov- PRESSURIZED EQUIPMENT HAZARD ing the cover.
- Page 10 Maintenance Daily CAUTION Check the main turbine filter daily for cleanliness. Do not operate the turbine sprayer without the filter The turbine systems are lifetime lubricated. The only installed. maintenance required is filter cleaning and replace- ment. Main filter screws The turbine main filter and pre-filter must be clean at all times to provide sufficient air flow to cool the motor and atomize the fluid.
-
Page 11: Troubleshooting
Troubleshooting PROBLEM CAUSE SOLUTION Remote Container Pressur- No fluid delivery. Check for leaks at the container gasket, ization 2 quart lid, and 2 1/2 gal pot wing nuts. Check for air flow from male quick–dis- connect at compressor outlet (approx. 1/4 CFM). - Page 12 Repair Top Cover WARNING Screws Turn off turbine and unplug power for the following procedures. Turbine Switch Replacement (Red Rocker Circuit Breaker) 1. To remove the turbine switch, wedge a large flat blade screwdriver between the top of the switch and the turbine face plate.
- Page 13 Repair Motor/Turbine Replacement Toggle Rocker Remove the cabinet wrapper by following the steps in Switch Compressor Switch the Turbine Wrapper Removal procedure. See Fig. 7 Motor for Series 1200 and Series 2000. Black Whit 1. The motor can now be replaced. Use the motor Green assembly kit M73526, which contains: rubber bottom spacer (46), foam fan seal (90), ground...
- Page 14 Parts for Series 1200 03077A 14 308423...
- Page 15 Parts for Series 1200 Part No. Description Part No. Description M70739 HANDLE, with grip M70609 FILTER, main M71603 DECAL, warning (not shown) M71188 VELCRO, strips M70603 SWITCH, toggle M70607 FILTER, pre M70811 SWITCH, plate M70773 WASHER, 1/4 M73030 DECAL, RH (not shown) 113400 SCREW M73031...
- Page 16 Parts for Series 2000 58 59 60 03078A 16 308423...
- Page 17 Parts for Series 2000 Part No. Description Part No. Description M70739 HANDLE, with grip M70607 FILTER, pre M71603 DECAL, warning (not shown) M70773 WASHER, 1/4 M70603 SWITCH, toggle 113400 SCREW M70811 SWITCH, plate M73014 MOUNT, motor, bottom M73032 DECAL, RH (not shown) M73013 MOUNT, motor, top M73033...
- Page 18 Accessories 2-1/2 Gallon Pressure Pot M70604 50 psi (3.5 bar) Maximum Inlet Air Pressure 2-1/2 gallon (9.5 liter) capacity, galvanized steel tank. Includes an air pressure regulator and gauge and a pressure relief valve. Ref. Part No. Description Qty. 104655 PRESSURE GAUGE 151519 HEX NIPPLE, 1/4 in.
- Page 19 Accessories 2 Quart Pressure Pot M70962 110440 M71491 HOSE, fluid; 5 ft. (1.5 m) long; 50 psi (3.5 bar) Maximum Inlet Air Pressure 1/4 in. (6.35 mm) ID 2 quart (1.94 liter) capacity, aluminum cup. M71470 HOSE, air; 4.5 ft. (1.4 m) long Includes an air pressure regulator and gauge, pressure M70854 HOSE CLAMP...
- Page 20 Accessories Lubricant 111–265 Air Control Valve M71681 One 4 oz (113 gram) tube sanitary (non-silicone) Compressor Unloader Valve Kit M70691 lubricant for fluid seals and wear areas. Series 1200 and 2000 Motor Assembly Kit M73526 #4 Ford Viscosity Cup M70702 Series 1200 to Series 2000 Conversion Kit M71513 To measure viscosity of fluid.
- Page 21 Notes 308423 21...
-
Page 22: The Graco Warranty And Disclaimers
Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub- stitution of non–Graco component parts.