Listening To The Radio - Sanyo DC-D40 Instruction Manual

LISTENING TO THE RADIO
Automatic or manual tuning
1.
2.
3.
4.
Select "TUNER".
Press the BAND button to select FM or AM,
For automatic tuning, make sure that "AUTO" is displayed, If not,
press the TUNE MODE button to display "AUTO".
Press the v or A TUNING button to tune in a station.
The unit stops automatically at the next receivable station. Press the
button again to continue.
AUTO
AM
594
kHz
- When receiving a station with weak signals, press the TUNE
MODE button to turn off "AUTO" (Manual tuning).
Press the V or A TUNING button continuously until you are
close to the desired frequency, then press it briefly until the desired
frequency is displayed. Each time the button is pressed, the fre-
quency changes in 0.05 MHz steps for FM and 9 kHz steps for AM.
To preset stations
Automatic presetting
1.
Select "TUNER".
2. Press and hold down both V and A PRESH buttons for at least 2
seconds. "APT" blinks on the display.
The automatic tuning mode is set and automatic presetting begins
from the low end of the FM band.
FM
90.75 MHz
CH
02
When 36 stations have been preset or the high end of the AM band is
reached, automatic presetting stops. "APT" disappears and the chan-
nel number 1 station will be heard.
Manual presetting
Up to 36 stations (for example: 26 FM and 10AM stations) can be preset
in any order.
Note:
Each preset can be set for one FM or one AM station. The presets can be
programmed for any combination of FM and AM stations.
1. Tune in the station to be preset as described in "Automatic or manual
tuning".
2. Press the MEMORY button. "MEMO' blinks.
\l/
AUTO MEMO
FM 103.25
Miiz
CH --
3.
4.
Press two number buttons (for example: 09,10,25, etc.) on the remote
control to preset the station. "MEMO" disappears.
- When using the PRESfl buttons, press the V or A button to
select the desired channel number, then press the MEMORY
button.
AUTO
FM 103.25
MHz
CH
09
-
In this example, "FM 103,25 MHz" station is preset on channel
number 9 (CH 09).
Note:
If the next step is not taken within 10 seconds in steps 2-3, "MEMO"
disappears and the preset operation is cancelled. Press the MEMORY
button to continue.
Repeat steps above, to add more preset stations.
When presetting a new station, the previously preset station on the
same channel is cleared.
The preset stations will be retained in the memory even if the unit is
turned off.
If the memory contents are lost due to a power failure or other
condition, preset the stations again,
Note:
If the band does not change when the BAND button is pressed, while
presetting or changing stations, use the PRESET button to find the
desired band.
If the band does not change with the PRESET button, disconnect the
mains lead, then press the RESH button (rear of the unit) for at least 20
seconds, Connect the mains lead and resume operation. In this case,
memory contents must be reset.
Listening to preset stations
1.
Select "TUNER",
2. Press two number buttons on the remote control within 3 seconds, or
the V or A PRESH button to select the desired channel number.
- For receiving an FM stereo broadcast, make sure that "MONO" is not
displayed. If "MONO" appears, press the FM MODE button to turn the
"MONO' indication off.
"STEREO" appears when an FM stereo broadcast is received.
- Ifthe signals from an FM stereo station are weak and reception is poor,
press the FM MODE button to change to monaural reception. ("STE-
REO" is replaced by "MONO" in the display.)
- If a channel numbe-r which has not been p~eset is selected, "--.--"
appears for 2 seconds and the previous station is selected.
r
I
Changing the AM reception frequencies
It
i s not necessary to perform this procedure in the Australia and New
Zealand.
1. Select the AM band.
2, Turn the power off.
3. While pressing the BAND button, press the POWER button.
522-1710 kHz (9 kHz steps) —520 -1710 kHz (10 kHz steps)
I
-9-