Listening To The Radio - Sanyo DC-F430AV Instruction Manual

LISTENING TO THE RADIO
Before use
When the unit is shipped from the factory, its AM frequency band ISset as
"522 -1710 kHz (in 9 kHz steps)".
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to "520 -1710 kHz (in 10 kHz steps)" as follows.
1. Press the TUNEFVBAND button to select "AM.
2. While pressing the MEMORY button on the front panel, press the
STOP button (CD section) on the front panel.
To return the original setting, repeat steps above.
4.
Press the MEMORY button.
In this example,"1 03.25 MHz" FM station is preset on FM channel
number 9.
The number buttons on the remote control can be used to select
the preset station. In this example, press O, then 9 after the step
2 above.
FYI 1113.25 'H'
5. Repeat the steps above to add more preset stations.
To turn the unit on and listen to the last received station, press the
TUNEFUBAND button.
Automatic/Manual tuning
1, Press the TUNER/BAND button to select FM or AM.
"TUNER" is selected automatically. 'TUNER" appears on the
display, then 'TUNER" is replaced by the tuner mode display.
Automatic tuning
2. Press the TUNING MODE button to select "AUTO, then turn the
MULTI JOG control to tune in a station.
- Or press the+ or – TUNING button on the remote control (more
than 0.7 seconds).
The unit will scan up or down the band and receive the next receivable
station. Perform the same operation to continue.
Manual tuning
2. Press the TUNING MODE button to select "MANUAL", then turn the
MULTI JOG control until the desired frequency is displayed.
Or press the+ or – TUNING button on the remote control briefly
(less than 0.7 seconds).
The frequency changes in 0.05 MHz steps for FM and 9 kHz/10 kHz
steps for AM.
Fl"l /03.25
MHZ
H
1234
5678
9 m ?$ 12
,3 1, 45 m
To preset stations
Up to 36 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic Drasettinq (APT)
1
2.
3.
Press the TUNE~/BAND button to select FM or AM.
Press and hold down the MEMORY button for at least 3 seconds. The
PRESET indicator lights and "PROG." blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 36 stations forFM(12 stations for AM) have been preset or the
high end of the band is reached, automatic presetting stops. "PROG."
disappears and the station memorized on channel number 1 will be
heard.
To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will be
cleared and new stations will be programmed.
Manual rwesettina
1.
2.
3.
Tun; in the st;tion to be preset as described in "Automatic/Manual
tuning".
Press the MEMORY button. The PRESET indicator lights.
— —
//33.25 'Hz
•E 1234
=5878
/,, s <0 ,1,2
,3 ,4 15 16
Turn the MULTI JOG control or press the PRESET button on the
remote control to select the channel number to be preset.
'3
IF13.25 '"
- When presetting a new station, the previously preset station on the
same channel number of the same band is cleared.
The preset stations will be retained in the memory even if the unit is
turned off.
If the memory contents are lost due to a power failure or other
condition, preset the stations again.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the TUNING MODE button to select "PRESE~, then turn the
MULTI JOG control to select the desired channel number.
Or press the PRESET button on the remote control (less than 0.7
seconds).
The number buttons on the remote control can also be used.
Press two number buttons within 4 seconds.
Preset scan tunirm
Press the TUN=R/BAND button to select FM or AM.
Press the PRESET button on the remote control (more than 0.7
seconds). The channel number blinks on the display. Each of the
preset stations is tuned in for 5 seconds.
When the desired station has been tuned in, press the PRESET button
again to keep the reception locked at that station.
To receive an FM stereo broadcast, make sure that "MONO" is not
displayed. If "MONO appears, press the FM MODE button to turn the
"MONO indication off.
'(ST" appears when an FM stereo broadcast is received.
If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to monaural reception. ("ST" is
replaced by "MONO in the display.)
When beat interference is heard
A high-pitched noise called "beat" is sometimes heard during reception of
radio broadcasts.
If this occurs,
1. Press the MEMORY button.
2. While "PROG." is blinking, press the !4+ /<+ button on the remote
control to select "be-A, "be-B, "be-C or "be-D. Select the setting that
gives the best results.
LISTENING TO VIDEO SOURCES/DVD
1. Press the VI DEO/DVD button. "VIDEO:DVD appears on the display.
2. Follow the instructions supplied with the video equipmenVDVD player.
•E ,234
_6678
,,, 9 01,12
,3 14 15 18
13